If the telephone transceiver assembly detects an error in communication between the telephone transceiver assembly and the airbag ECU assembly as a result of the telephone transceiver assembly self check, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C464 | Airbag Signal Signal Plausibility Failure | Telephone transceiver assembly detects an error in signals from airbag ECU assembly when ignition switch is ON. |
·
Airbag system
·
Harness or connector
·
Airbag ECU assembly
·
Telephone transceiver assembly |
Telematics | B |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds.
Procedure1
Check the DTC of "AIRBAG SYSTEM".
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
Post-procedure1
None
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
| *a | Component with harness connected (Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly but do not disconnect the connectors.
Procedure1
Check the input waveform.
Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telephone transceiver assembly while the airbag ECU assembly connectors are connected.)
| Item | Condition |
|---|---|
| Tester connection | I55-13 (GSW) - Body ground |
| Tool setting | 5.0 V/DIV., 20 ms/DIV. |
| Vehicle condition | Ignition switch ON |
The waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telephone transceiver assembly with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the I55 telephone transceiver assembly connector.
Disconnect the I24 airbag ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I55,I24)Location & Routingewd_type=routing;type=c,c;code=I55,I24 |
||
| I55-13 (GSW) - I24-23 (GSW3) | Always | Below 1 Ω |
| I55-13 (GSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG