The No. 1 skid control ECU (brake booster with master cylinder assembly) receives signals from the ECM, TCM*1, TCM (ECM)*2 and No. 2 skid control ECU (brake actuator assembly) via CAN communication.
*1: except 1GR-FE
*2: for 1GR-FE
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| U010000 | Lost Communication with ECM/PCM "A" | When the voltage at terminal IG1 is 9.5 V or more, communication between the ECM and No. 1 skid control ECU (brake booster with master cylinder assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
ECM
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| U010100 | Lost Communication with TCM | When the voltage at terminal IG1 is 9.5 V or more, communication between the TCM and No. 1 skid control ECU (brake booster with master cylinder assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
TCM*1
·
TCM (ECM)*2
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| U012987 | Lost Communication with Brake System Control Module "A" Missing Message | When the voltage at terminal IG1 is 9.5 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
No. 2 skid control ECU (brake actuator assembly)
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| U110600 | Lost Communication with Electric Parking Brake Module | With terminal IG1 voltage at 9.5 V or more, data cannot be received from the No. 2 skid control ECU (brake actuator assembly) for 1 second or more. |
·
CAN communication line
·
No. 2 skid control ECU (brake actuator assembly)
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| U115C00 | Lost Communication with ECM/PCM "A" (ch5) | When the voltage at terminal IG1 is 9.5 V or more, communication between the ECM and No. 1 skid control ECU (brake booster with master cylinder assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
ECM
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| U117D87 | Lost Communication with Brake System Control Module (ch4) Missing Message | When the voltage at terminal IG1 is 9.5 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
No. 2 skid control ECU (brake actuator assembly)
·
No. 1 skid control ECU (brake booster with master cylinder assembly) |
Brake Booster | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
*1: except 1GR-FE
*2: for 1GR-FE
Perform the Health Check using the GTS.
| Result | Proceed to |
|---|---|
| DTCs for related systems are output together with U010000, U010100, U012987, U110600, U115C00 or U117D87 | A |
| U010000, U010100, U012987, U110600, U115C00 or U117D87 is output | B |
| DTCs are not output | C |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING