CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector (to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 1 skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
|||
| B19-1 (MRI1) - Body ground | Brake booster with accumulator pump assembly power supply input | Always | 11 to 14 V |
| B19-2 (MGND) - Body ground | Brake booster with accumulator pump assembly ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| B19-3 (SKS1) | Brake pedal stroke sensor 1 signal input | - | - |
| B19-4 | - | - | - |
| B19-5 (EXI4) | Turn assist function switch (transfer position switch) signal input | - | - |
| B19-6 | - | - | - |
| B19-7 | - | - | - |
| B19-8 | - | - | - |
| B19-9 | - | - | - |
| B19-10 | - | - | - |
| B19-11 | - | - | - |
| B19-12 (LBL) | Brake fluid level warning switch (Brake booster with master cylinder assembly) input | - | - |
| B19-13 | - | - | - |
| B19-14 (+BI1) - Body ground | +BI1 power source input | Always | 11 to 14 V*1 10.5 to 16 V*2 |
| B19-15 (BS) - Body ground | Solenoid power supply input | Always | 11 to 14 V |
| B19-16 (VSK1) | Brake pedal stroke sensor 1 power supply output | - | - |
| B19-17 | - | - | - |
| B19-18 (SKG1) | Brake pedal stroke sensor 1 ground | - | - |
| B19-19 | - | - | - |
| B19-20 | - | - | - |
| B19-21 | - | - | - |
| B19-22 | - | - | - |
| B19-23 | - | - | - |
| B19-24 | - | - | - |
| B19-25 (CSW2) | No. 2 skid control ECU (brake actuator assembly) operation signal output | - | - |
| B19-26 | - | - | - |
| B19-27 | - | - | - |
| B19-28 (GND1) - Body ground | No. 1 skid control ECU (Brake booster with master cylinder assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| B19-29 (M+) | Brake booster with accumulator pump assembly power supply (+) | - | - |
| B19-30 (M-) | Brake booster with accumulator pump assembly power supply (-) | - | - |
| B19-31 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V*1 10.5 to 16 V*2 |
| B19-32 | - | - | - |
| B19-33 | - | - | - |
| B19-34 (HDCS) | Downhill assist control/crawl control switch (integration control and panel sub-assembly) ON | - | - |
| B19-35 (CA2H) | CAN communication line 2 (H) | - | - |
| B19-36 (CA2L) | CAN communication line 2 (L) | - | - |
| B19-37 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| B19-38 (CA1H) | CAN communication line 1 (H) | - | - |
| B19-39 (CA1L) | CAN communication line 1 (L) | - | - |
| B19-40 (CTY) - Body ground | Front door courtesy light switch assembly input (for driver side) | Driver door closed → open | 11 to 14 V → Below 1.5 V |
| B19-41 | - | - | - |
| B19-42 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
CHECK BRAKE ACTUATOR ASSEMBLY
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector (to No. 2 Skid Control ECU (brake actuator assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 2 skid control ECU (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
|||
| B20-1 (GND1) - Body ground | No. 2 skid control ECU (brake actuator assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| B20-2 | - | - | - |
| B20-3 | - | - | - |
| B20-4 (RL-) | Rear speed sensor LH (-) signal input | - | - |
| B20-5 (RL+) | Rear speed sensor LH (+) power supply output | - | - |
| B20-6 (FR-) | Front speed sensor RH (-) signal input | - | - |
| B20-7 (FR+) | Front speed sensor RH (+) power supply output | - | - |
| B20-8 | - | - | - |
| B20-9 (CSW) - Body ground | VSC OFF switch input | VSC OFF switch is pushed → released | Below 1 Ω → 10 kΩ or higher |
| B20-10 (SKS2) | Brake pedal stroke sensor 2 signal input | - | - |
| B20-11 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| B20-12 | - | - | - |
| B20-13 | - | - | - |
| B20-14 (+BS) - Body ground | ABS solenoid relay power supply input | Always | 11 to 14 V |
| B20-15 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
| B20-16 (CA2H) | CAN communication line 2 (H) | - | - |
| B20-17 (CA2L) | CAN communication line 2 (L) | - | - |
| B20-18 (SP1) | Speed sensor signal output | - | - |
| B20-19 (RR-) | Rear speed sensor RH (-) signal input | - | - |
| B20-20 (RR+) | Rear speed sensor RH (+) power supply output | - | - |
| B20-21 (FL-) | Front speed sensor LH (-) signal input | - | - |
| B20-22 (FL+) | Front speed sensor LH (+) power supply output | - | - |
| B20-23 | - | - | - |
| B20-24 | - | - | - |
| B20-25 (VSK2) | Brake pedal stroke sensor 2 power supply output | - | - |
| B20-26 (SKG2) | Brake pedal stroke sensor 2 ground | - | - |
| B20-27 (CANH) | CAN communication line (H) | - | - |
| B20-28 | - | - | - |
| B20-29 (CTY) - Body ground | No. 2 Skid control ECU (brake actuator assembly) operation signal input | Ignition switch ON | 11 to 14 V |
| B20-30 (GND2) - Body ground | ABS motor ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| B20-31 | - | - | - |
| B20-32 (STPO) - Body ground | Stop light control relay (stop light switch assembly) output | Always | 11 to 14 V |
| B20-33 | - | - | - |
| B20-34 | - | - | - |
| B20-35 (BH) - Body ground | Brake hold switch (electric parking brake switch assembly) input | Brake hold switch (electric parking brake switch assembly) is pushed → released | Below 1 Ω → 10 kΩ or higher |
| B20-36 | - | - | - |
| B20-37 (STP2) - Body ground | Stop light control relay (stop light switch assembly) input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| B20-38 | - | - | - |
| B20-39 | - | - | - |
| B20-40 | - | - | - |
| B20-41 | - | - | - |
| B20-42 | - | - | - |
| B20-43 (CANL) | CAN communication line (L) | - | - |
| B20-44 | - | - | - |
| B20-45 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V*1 10.5 to 16 V*2 |
| B20-46 (BM) - Body ground | ABS motor relay power supply input | Always | 11 to 14 V |
TERMINALS OF ECU (STEERING SENSOR)
| *a | Component without harness connected (Steering Sensor) | - | - |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 | - (Not used) |
| 2 (2S) | Wiper motor operation signal |
| 3 (CANH) | CAN communication line H |
| 4 (BAT) | ECU power supply input |
| 5 | - (Not used) |
| 6 (ESS) | Body ground |
| 7 (HEAD) | Headlight operation signal |
| 8 (CANL) | CAN communication line L |
| 9 (IG1) | IG1 power source input |
| 10 | - (Not used) |
TERMINAL INSPECTION (STEERING SENSOR)
Disconnect the I51 connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector (to Steering Sensor) |
- | - |
Voltage cannot be measured with the connector connected to the steering sensor as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I51-4 (BAT) - Body ground | ECU power supply output | Always | 11 to 14 V |
| I51-6 (ESS) - Body ground | Body ground | 1 minute or more after disconnecting the cable from the negative (-) battery terminal | Below 1 Ω |
| I51-9 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |