Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The airbag sensor with ECU assembly has a built-in acceleration sensor.

This DTC is stored when the No. 2 skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the airbag sensor with ECU assembly.

This DTC may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed exceeding 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness and connector

·

Acceleration sensor (airbag sensor with ECU assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C427101E08
5.188,4.135 7.083,4.656 1.896,0.521 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.177,3.948 5.583,4.156 0.406,0.208 10 false B20 5.781,1.125 6.188,1.333 0.406,0.208 10 false 27 5.781,0.521 6.188,0.729 0.406,0.208 10 false 43 6.052,1.313 6.51,1.521 0.458,0.208 10 false CANH 6.063,0.698 6.521,0.906 0.458,0.208 10 false CANL 0.802,0.708 1.26,0.917 0.458,0.208 10 false CAFL 0.76,1.313 1.219,1.521 0.458,0.208 10 false CAFH 0.917,1.938 1.375,2.146 0.458,0.208 10 false IGR 1.292,1.802 1.75,2.01 0.458,0.208 10 false 36 2.125,2.094 3.208,2.323 1.083,0.229 10 false A/BAG-IGR 3.979,1.927 5.156,2.156 1.177,0.229 10 false from IG Circuit 0.969,3.125 1.427,3.333 0.458,0.208 10 false E2 1.292,3.052 1.479,3.26 0.188,0.208 10 false 32 0.271,4.052 0.729,4.26 0.458,0.208 10 false I24 0.271,4.219 1.948,4.74 1.677,0.521 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor with ECU Assembly) 3.458,3.115 5.198,3.417 1.74,0.302 10 false : CAN Communication Line 1.292,0.49 1.698,0.698 0.406,0.208 10 false 27 1.292,1.125 1.698,1.333 0.406,0.208 10 false 26 1.292,2.417 1.75,2.625 0.458,0.208 10 false 33 0.969,2.531 1.427,2.74 0.458,0.208 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor with ECU assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE



a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



d.

Disconnect the I24 yaw rate and acceleration sensor (airbag sensor with ECU assembly) connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Connect the cable to the negative (-) battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I24)Location & Routing

Click Connector(I24)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Airbag with ECU Sensor Assembly

I24-36 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I24)Location & Routing

Click Connector(I24)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Airbag with ECU Sensor Assembly

I24-33 (E1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω
I24-32 (E2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the I24 yaw rate and acceleration sensor (airbag sensor with ECU assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C14D71C is not output A
C14D71C is output B



A

B