The yaw rate and acceleration sensor has a built-in airbag sensor with ECU assembly.
The No. 2 skid control ECU (brake actuator assembly) receives signals from the ECM, TCM*1, TCM (ECM)*2, 4 wheel drive control ECU, yaw rate and acceleration sensor (airbag sensor with ECU assembly), steering sensor, No. 1 skid control ECU (brake booster with master cylinder assembly) and airbag sensor with ECU assembly via CAN communication.
*1: except 1GR-FE
*2: for 1GR-FE
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | When data from the ECM cannot be received continuously for 2 seconds or more |
·
CAN communication line
·
ECM
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U010187 | Lost Communication with TCM Missing Message | When data from the TCM cannot be received continuously for 2 seconds or more |
·
CAN communication line
·
TCM*1
·
TCM (ECM)*2
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U011487 | Lost Communication with Four-Wheel Drive Clutch Control Module Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V, data from the 4 wheel drive control ECU cannot be received for 1 second or more. |
·
CAN communication line
·
4 wheel drive control ECU
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more. |
·
CAN communication line
·
Yaw rate and acceleration sensor (airbag sensor with ECU assembly)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering sensor cannot be received for 1 second or more. |
·
CAN communication line
·
Steering sensor
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U014087 | Lost Communication with Body Control Module Missing Message | When terminal IG1 voltage is 10 V or more, data from the main body ECU cannot be received for 2 seconds or more. |
·
CAN communication line
·
Main body ECU (multiplex network body ECU)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U015187 | Lost Communication with Restraints Control Module Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 7 km/h (4 mph), data cannot be received from the airbag sensor with ECU assembly for 5 seconds or more. |
·
CAN communication line
·
Airbag sensor with ECU assembly
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U025E87 | Lost Communication with Electronic Brake Booster Control Module "A" Missing Message | When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
No. 1 skid control ECU (brake booster with master cylinder assembly)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U115987 | Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message | When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more. |
·
CAN communication line
·
No. 1 skid control ECU (brake booster with master cylinder assembly)
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| U115C87 | Lost Communication with ECM/PCM "A" (ch5) Missing Message | When data from the ECM cannot be received continuously for 2 seconds or more |
·
CAN communication line
·
ECM
·
No. 2 skid control ECU (brake actuator assembly) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
*1: except 1GR-FE
*2: for 1GR-FE
Perform the Health Check using the GTS.
| Result | Proceed to |
|---|---|
| DTCs for related systems are output together with U010087, U010187, U011487, U012587, U012687, U014087, U015187, U025E87, U115987 or U115C87 | A |
| U010087, U010187, U011487, U012587, U012687, U014087, U015187, U025E87, U115987 or U115C87 is output | B |
| DTCs are not output | C |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING