Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C110000  Brake Pedal Position Sensor "A" Supply Voltage Malfunction  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C110000 Brake Pedal Position Sensor "A" Supply Voltage Malfunction When the voltage at terminal +BI1 is 7.3 V or more, the value of brake pedal stroke sensor 1 is invalid for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427351E09
4.885,0.667 5.354,0.906 0.469,0.24 10 false VSK1 4.885,1.292 5.344,1.521 0.458,0.229 10 false SKS1 4.875,1.917 5.375,2.208 0.5,0.292 10 false SKG1 4.625,0.458 4.938,0.656 0.313,0.198 10 false 16 4.688,1.073 5,1.271 0.313,0.198 10 false 3 4.625,1.688 4.938,1.885 0.313,0.198 10 false 18 4.49,2.24 4.969,2.427 0.479,0.188 10 false B19 4.479,2.406 6.917,2.771 2.438,0.365 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.74,0.448 3.052,0.646 0.313,0.198 10 false 4 2.74,4.531 3.052,4.729 0.313,0.198 10 false 3 2.74,3.906 3.052,4.104 0.313,0.198 10 false 1 2.74,3.292 3.052,3.49 0.313,0.198 10 false 2 2.74,1.073 3.052,1.271 0.313,0.198 10 false 6 2.74,1.688 3.052,1.885 0.313,0.198 10 false 5 0.344,5.052 0.927,5.24 0.583,0.188 10 false B15 0.333,5.219 2.792,5.583 2.458,0.365 10 false Brake Pedal Stroke Sensor Assembly 2.24,0.677 2.708,0.917 0.469,0.24 10 false VCSK 2.25,1.292 2.708,1.521 0.458,0.229 10 false SKS1 2.313,1.906 2.813,2.198 0.5,0.292 10 false SKG 2.271,3.521 2.75,3.781 0.479,0.26 10 false VSK2 2.26,4.135 2.729,4.406 0.469,0.271 10 false SKS2 2.25,4.76 2.771,5.042 0.521,0.281 10 false SKG2 4.469,5.24 6.948,5.646 2.479,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.479,5.063 5.052,5.25 0.573,0.188 10 false B20 4.865,3.521 5.344,3.781 0.479,0.26 10 false VSK2 4.854,4.135 5.323,4.406 0.469,0.271 10 false SKS2 4.854,4.76 5.375,5.042 0.521,0.281 10 false SKG2 4.604,3.292 4.917,3.49 0.313,0.198 10 false 25 4.594,3.906 4.906,4.104 0.313,0.198 10 false 10 4.604,4.531 4.917,4.729 0.313,0.198 10 false 26 6.458,1.198 6.771,1.396 0.313,0.198 10 false IC 6.438,4.052 6.75,4.25 0.313,0.198 10 false IC 0.5,1.094 0.875,1.698 0.375,0.604 10 false HALL IC1 0.469,3.969 0.844,4.573 0.375,0.604 10 false HALL IC2

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the B15 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B19,B15)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(B15)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Brake Pedal Stroke Sensor Assembly

B19-3 (SKS1) - B15-6 (SKS1) Always Below 1 Ω
B19-3 (SKS1) or B15-6 (SKS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR