FREEZE FRAME DATA
Using the GTS, check the vehicle condition (ECU, sensor) when a DTC is output.
CHECK FREEZE FRAME DATA WHEN DTC WAS STORED
Freeze Frame Data is stored when a DTC is output.
Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Check the Freeze Frame Data when a DTC is output.
Select a DTC to display the Freeze Frame Data.
Check the Freeze Frame Data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0 Max.: 16777215 |
- | - |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake status | OFF / ON | OFF: Parking brake released ON: Parking brake applied |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Reservoir Warning SW | Brake fluid level warning switch | OFF / ON | OFF: Reservoir level normal ON: Reservoir level low |
- |
| ECB Motor Relay | Motor relay operation request | OFF / ON | OFF: Relay off ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SGH) | Switching solenoid valve (SGH) | OFF / ON | OFF: Solenoid off ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SSA) | Switching solenoid valve (SSA) | OFF / ON | OFF: Solenoid off ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 OFF ON: IGP_PT1 ON |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 OFF ON: IGP_PT2 ON |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in wire harness between No. 1 skid control ECU (brake booster with master cylinder assembly) and stop light switch assembly status | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Stroke Open | Brake pedal stroke sensor 1 open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Accumulator Open | Accumulator pressure sensor open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure Sensor Open | Reaction force pressure sensor open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Servo Pressure Sensor Open | Servo pressure sensor open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa Max.: 24.48 MPa |
Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm Max.: 255 mm |
Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa Max.: 24.48 MPa |
0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal Brake pedal released: 0.00 to 1.53 MPa |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa Max.: 24.48 MPa |
0.00 to 21.60 MPa | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Voltage of Stroke Sensor | Voltage of brake pedal stroke sensor 1 | Min.: 0.000 V Max.: 5.000 V |
- | - |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s Max.: 2540 mm/s |
Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| Reaction Force Oil Pressure Change Speed | Reaction force pressure rate of change | Min.: -30 MPa/s Max.: 225 MPa/s |
- | - |
| Target Oil Pressure | Wheel target hydraulic pressure | Min.: 0.00 MPa Max.: 20.00 MPa |
- | Changes according to the target wheel cylinder hydraulic pressure |
| VCSK Voltage Value | VCSK voltage value | Min.: 0.000 V Max.: 5.500 V |
4.800 to 5.200 V | - |
| SLA Solenoid Current | Linear solenoid addition valve (SLA) current | Min.: 0.000 A Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SLR Solenoid Current | Linear solenoid reduction valve (SLR) current | Min.: 0.000 A Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SGH Solenoid Current | Switching solenoid valve (SGH) current | Min.: 0.000 A Max.: 3.000 A |
0.000 to 1.500 A | - |
| SSA Solenoid Current | Switching solenoid valve (SSA) current | Min.: 0.000 A Max.: 3.000 A |
0.000 to 1.500 A | - |
| IGP Voltage | IG1 voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| IGR Voltage | IG2 voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| BI Voltage | +BI voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| BS Voltage | BS voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
*1: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE
*2: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0 Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa Max.: 23.99 MPa |
Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| Master Cylinder Sensor Temperature | Master cylinder pressure sensor temperature | Min.: -80°C (-112°F) Max.: 175°C (347°F) |
Current master cylinder pressure sensor temperature | - |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2 Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2 Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering sensor | Min.: -3276.8° Max.: 3276.7° |
Turning left: 0.0 to 3276.7° Turning right: -3276.8 to 0.0° |
- |
| Zero Point of Steering Angle | Memorized zero point value of steering sensor | Min.: -3276.8° Max.: 3276.7° |
- | - |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V Max.: 25.5 V |
Ignition switch ON: 0.0 to 4.7 V | Changes in proportion to battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to battery voltage
|
| Engine Revolutions | Engine speed | Min.: 0 rpm Max.: 65535 rpm |
Actual engine speed | - |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0% Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Power Train Driving force | Powertrain driving force | Min.: -327680 N Max.: 327670 N |
- | - |
| Gear Position | Gear position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC expert mode (VSC expert mode MID ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode VSC expert mode (VSC expert mode MID ON): VSC expert mode VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode / Pressure hold mode / Pressure release mode / EPB lock mode | Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated) Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold operated indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed | Vehicle speed (Vehicle speed signal output to combination meter assembly) |
Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle acceleration/deceleration | Min.: -25.105 m/s2 Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2 During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s Max.: 1275 s |
- | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s Max.: 1275 s |
- | - |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Downhill Assist Control/Crawl Control SW | Downhill assist control/crawl control switch (integration control and panel sub-assembly) ON status (HDCS terminal input) |
OFF / ON | OFF: Downhill assist control/crawl control switch (integration control and panel sub-assembly) OFF ON: Downhill assist control/crawl control switch (integration control and panel sub-assembly) ON |
w/ Downhill Assist Control System/Crawl Control System |
| Stop Light SW | Stop light switch assembly status (STP or STP2 terminal input) |
OFF / ON | OFF: Brake pedal released ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake status | OFF / ON | OFF: Parking brake released ON: Parking brake applied |
- |
| Rear Diff Lock Switch | Rear differential lock status | OFF / ON | OFF: Rear differential lock free ON: Rear differential lock ON |
- |
| Automatic Disconnect Diff SW | Center differential lock status | OFF / ON | OFF: Center differential lock free ON: Center differential lock ON |
- |
| L4 Switch | Transfer position switch status | OFF / ON | OFF: except L4 ON: L4 |
- |
| Reverse Position Switch | Reverse position switch status | OFF / ON | OFF: Shift lever position is not in R ON: Shift lever position is in R |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (BH terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (stop light switch assembly) status (STP terminal input) |
OFF / ON | OFF: Stop light control relay (stop light switch assembly) off and brake pedal released ON: Stop light control relay (stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode ON: Inspection mode |
- |
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control Under Controlling: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control ON: During control |
- |
| Stop Light Relay State for ECU Control | Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) | OFF / ON | OFF: Stop light control relay (stop light switch assembly) off (Stop light off) ON: Stop light control relay (stop light switch assembly) on (Stop light on) |
- |
| Engine Stop by Stop and Start System | Engine stopped by stop and start system status (value detected by ECU) | OFF / ON | OFF: Engine not stopped by stop and start control ON: Engine stopped by stop and start control |
w/ Stop and Start System |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating ON: ABS motor relay operating |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF ON: VSC OFF switch ON |
|
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 OFF ON: IGP_PT1 ON |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| FR Speed Open | Momentary interruption of front speed sensor RH pulse input to ECU | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| FL Speed Open | Momentary interruption of front speed sensor LH pulse input to ECU | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| RR Speed Open | Momentary interruption of rear speed sensor RH pulse input to ECU | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| RL Speed Open | Momentary interruption of rear speed sensor LH pulse input to ECU | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| EFI Communication Open | ECM communication open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor (airbag sensor with ECU assembly) open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Deceleration Open | Acceleration sensor (airbag sensor with ECU assembly) open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor (airbag sensor with ECU assembly) voltage open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| EFI Communication Invalid | ECM communication invalid detection | Normal / Under intermittent | Normal: Normal Under intermittent: ECM communication invalid state detection |
- |
| Master Cylinder Pressure Sensor Power Supply Open | Master cylinder pressure sensor power supply voltage status | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Solenoid Power Supply Open | Solenoid power supply voltage status | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Motor Power Supply Open | Motor power supply voltage status | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in wire harness between No. 2 skid control ECU (brake actuator assembly) and stop light switch assembly status | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| A/C ECU Communication Open | Air conditioning Amplifier assembly open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Stop and Start ECU Communication Open | Engine stop and start ECU open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
w/ Stop and Start System |
| Air Bag ECU Communication Open | Airbag sensor with ECU assembly open detection open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Stroke2 Open | Brake pedal stroke sensor 2 open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Body ECU Communication Open | Main body ECU (multiplex network body ECU) communication open detection | Normal / Under intermittent | Normal: Normal Under intermittent: Momentary interruption |
- |
| Brake Hold Ready | Brake hold control permission status | Not in stand-by mode / Stand-by mode | Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated) Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated) |
- |
| Stroke Sensor2 | Brake pedal stroke sensor 2 | Min.: 0.0 V Max.: 5.0 V |
Brake pedal released: 3.6 to 4.4 V | Reading decreases when brake pedal is depressed |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm Max.: 255 mm |
Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Voltage of Stroke Sensor2 | Voltage of brake pedal stroke sensor 2 | Min.: 0.000 V Max.: 5.000 V |
- | - |
| FR Regenerative Request | FR regenerative request torque | Min.: 0 Nm Max.: 1048560 Nm |
- | Although the item is displayed on the GTS, it is not applicable to the vehicle. |
| FR Regenerative Operation | FR regenerative operation torque | Min.: 0 Nm Max.: 1048560 Nm |
- | Although the item is displayed on the GTS, it is not applicable to the vehicle. |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s Max.: 2540 mm/s |
Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| VCSK Voltage Value | VSK2 voltage value | Min.: 0.000 V Max.: 5.500 V |
4.800 to 5.200 V | - |
| IGR Voltage | IG1 voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| +BS Voltage | +BS voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| +BM Voltage | BM voltage value | Min.: 0.0 V Max.: 25.5 V |
- | Changes in proportion to battery voltage |
| Voltage Difference between Motor Input-Output Terminal | Voltage difference between motor Input-output terminal | Min.: -640.00 V Max.: 639.98 V |
- | - |
*1: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE
*2: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the Freeze Frame Data.
Clear the DTCs and Freeze Frame Data.
Press the clear button.