The display signal from the rear television camera assembly is transmitted to the radio and display receiver assembly.
Disconnect the I13 radio and display receiver assembly connector.
Disconnect the g10 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I13,g10)Location & Routingewd_type=routing;type=c,c;code=I13,g10 Click Connector(g10)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=g10;pinno=6,3,5,2 |
||
| I13-30 (CA+) - g10-6 (CB+) | Always | Below 1 Ω |
| I13-28 (V+) - g10-3 (CV+) | Always | Below 1 Ω |
| I13-27 (CGND) - g10-5 (CGND) | Always | Below 1 Ω |
| I13-29 (V-) - g10-2 (CV-) | Always | Below 1 Ω |
| I13-30 (CA+) or g10-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| I13-28 (V+) or g10-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| I13-27 (CGND) or g10-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| I13-29 (V-) or g10-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| I13-26 (CSLD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radio and display receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I13)Location & Routingewd_type=routing;type=c;code=I13 |
||
| I13-29 (V-) - Body ground | Always | Below 1 Ω |
| I13-27 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I13)Location & Routingewd_type=routing;type=c;code=I13 |
||
| I13-30 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Remove the radio and display receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I13-28 (V+) - I13-29 (V-) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG
Replace the rear television camera assembly with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL
Check if the same malfunction recurs when the rear view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL