Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469672 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly, radio and display receiver assembly*1 or multi-display assembly*2 are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly*1

·

Multi-display assembly*2


Rear Camera A

*1: except 12.3 Inch Display

*2: for 12.3 Inch Display

WIRING DIAGRAM

except 12.3 Inch Display:
E378706E57
1.615,0.688 2.104,0.906 0.49,0.219 10 false CA+ 1.479,1.177 1.969,1.396 0.49,0.219 10 false CGND 1.99,0.583 2.479,0.802 0.49,0.219 10 false 30 1.99,1.052 2.479,1.271 0.49,0.219 10 false 27 5.094,1.063 5.583,1.281 0.49,0.219 10 false 5 5.094,0.583 5.583,0.802 0.49,0.219 10 false 6 4.969,1.719 5.458,1.938 0.49,0.219 10 false g9 4.969,1.885 7.156,2.198 2.188,0.313 10 false Rear Television Camera Assembly 0.75,1.708 1.24,1.927 0.49,0.219 10 false I13 0.74,1.885 2.479,2.302 1.74,0.417 10 false Radio and Display Receiver Assembly 5.281,0.708 5.771,0.927 0.49,0.219 10 false CB+ 5.281,1.188 5.771,1.406 0.49,0.219 10 false CGND

for 12.3 Inch Display:
E432780E23
1.667,0.479 2,0.646 0.333,0.167 10 false CA+ 1.563,1.271 2,1.448 0.438,0.177 10 false CGND 2.042,0.365 2.313,0.542 0.271,0.177 10 false 10 2.052,1.146 2.219,1.323 0.167,0.177 10 false 21 5.333,1.167 5.823,1.385 0.49,0.219 10 false 5 5.333,0.385 5.813,0.583 0.479,0.198 10 false 6 5.208,1.75 5.698,1.969 0.49,0.219 10 false g9 5.198,1.917 6.719,2.385 1.521,0.469 10 false Rear Television Camera Assembly 0.896,1.625 1.229,1.802 0.333,0.177 10 false I18 0.896,1.792 2.5,2.073 1.604,0.281 10 false Multi-display Assembly 5.583,0.469 6.073,0.688 0.49,0.219 10 false CB+ 5.583,1.271 6.073,1.49 0.49,0.219 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:
·

When the "!" mark is displayed on the display after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
except 12.3 Inch Display A
for 12.3 Inch Display B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the I13 radio and display receiver assembly connector.


b.

Disconnect the g9 rear television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13,g9)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

I13-30 (CA+) - g9-6 (CB+) Always Below 1 Ω
I13-27 (CGND) - g9-5 (CGND) Always Below 1 Ω
I13-30 (CA+) or g9-6 (CB+) - Body ground Always 10 kΩ or higher
I13-27 (CGND) or g9-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

Pre-procedure1

a.

Remove the radio and display receiver assembly with its connectors still connected.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


E404546C22
5.552,1.146 6.177,1.396 0.625,0.25 3.156,0.427 3.427,0.427 3.427,0.427 3.792,1.625 true 4.198,1.625 4.469,0.344 4.469,0.344 4.708,0.344 true 5.75,1.188 6.208,1.385 0.458,0.198 10 false I13 4.802,0.281 5.396,0.49 0.594,0.208 10 false CGND 2.875,0.354 3.469,0.563 0.594,0.208 10 false CA+ 1.063,0.646 1.438,0.99 0.375,0.344 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -



b.

Disconnect the g9 television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-27 (CGND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I13)Location & Routing

Click Connector(I13)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

I13-30 (CA+) - I13-27 (CGND) Ignition switch ACC 5.5 to 7.05 V
I13-30 (CA+) - I13-27 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

e.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the I18 multi-display assembly connector.


b.

Disconnect the g9 rear television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I18,g9)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

Click Connector(g9)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Television Camera Assembly

I18-10 (CA+) - g9-6 (CB+) Always Below 1 Ω
I18-21 (CGND) - g9-5 (CGND) Always Below 1 Ω
I18-10 (CA+) or g9-6 (CB+) - Body ground Always 10 kΩ or higher
I18-21 (CGND) or g9-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

5.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MULTI-DISPLAY ASSEMBLY

Pre-procedure1

a.
E367725C17
1.542,0.271 1.917,0.542 0.375,0.271 0.802,0.729 1.354,1.156 true 0.865,1.75 1.448,1.302 true 1.604,0.302 1.979,0.5 0.375,0.198 10 false I18 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.49,0.635 0.917,0.833 0.427,0.198 10 false CA+ 0.427,1.698 0.948,1.906 0.521,0.208 10 false CGND
*a Component with harness connected
(Multi-display Assembly)


Disconnect the g9 rear television camera assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I18)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I18-21 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I18)Location & Routing

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I18-10 (CA+) - I18-21 (CGND) Ignition switch ACC 5.5 to 7.05 V
I18-10 (CA+) - I18-21 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG