Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL INJECTOR (for Direct Injection)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470022 FUEL INJECTOR(for Direct Injection) G

V35A-FTS FUEL  FUEL INJECTOR(for Direct Injection)  INSPECTION  


PROCEDURE

Hide 23250E 1.INSPECT DIRECT FUEL INJECTOR ASSEMBLY

NOTICE:

This inspection is for checking the direct fuel injector assembly for an open or short. Because the direct fuel injector assembly of this vehicle is a high-pressure type, fuel injection volume cannot be checked.


a.
A333795C05
0.792,0.042 1.115,0.229 0.323,0.188 1.542,0.031 1.865,0.219 0.323,0.188 2.188,0.031 2.51,0.219 0.323,0.188 0.781,0.271 1.104,0.458 0.323,0.188 1.531,0.24 1.854,0.427 0.323,0.188 2.188,0.26 2.51,0.448 0.323,0.188 0.115,0.094 0.354,0.281 0.24,0.188 10 false *a 0.854,0.052 1.073,0.229 0.219,0.177 10 false D1 1.604,0.052 1.823,0.229 0.219,0.177 10 false E1 2.25,0.052 2.469,0.229 0.219,0.177 10 false D2 0.865,0.281 1.083,0.458 0.219,0.177 10 false E2 1.604,0.26 1.823,0.438 0.219,0.177 10 false D3 2.25,0.271 2.469,0.448 0.219,0.177 10 false E3
*a Component without harness connected
(Direct Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D1,E1,D2,E2,D3,E3)Location & Routing

Click Connector(D1)Engine Compartment>No. 5 Engine Wire>No. 1 Fuel Injector Assembly (for Direct Injection)

Click Connector(E1)Engine Compartment>No. 6 Engine Wire>No. 2 Fuel Injector Assembly (for Direct Injection)

Click Connector(D2)Engine Compartment>No. 5 Engine Wire>No. 3 Fuel Injector Assembly (for Direct Injection)

Click Connector(E2)Engine Compartment>No. 6 Engine Wire>No. 4 Fuel Injector Assembly (for Direct Injection)

Click Connector(D3)Engine Compartment>No. 5 Engine Wire>No. 5 Fuel Injector Assembly (for Direct Injection)

Click Connector(E3)Engine Compartment>No. 6 Engine Wire>No. 6 Fuel Injector Assembly (for Direct Injection)

D1-1 - D1-2 20°C (68°F) 1.34 to 1.64 Ω
E1-1 - E1-2 20°C (68°F) 1.34 to 1.64 Ω
D2-1 - D2-2 20°C (68°F) 1.34 to 1.64 Ω
E2-1 - E2-2 20°C (68°F) 1.34 to 1.64 Ω
D3-1 - D3-2 20°C (68°F) 1.34 to 1.64 Ω
E3-1 - E3-2 20°C (68°F) 1.34 to 1.64 Ω


If the result is not as specified, replace the direct fuel injector assembly.