83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY
Check the fuel sender gauge assembly output voltage.
| *a | Component without harness connected (Fuel Sender Gauge Assembly) |
| *b | Voltage applied between terminals |
Apply 5 V between terminals 1 (FV) and 2 (FE).
Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.
Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).
If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.
| *a | Component without harness connected (Fuel Sender Gauge Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(V8)Location & Routingewd_type=routing;type=c;code=V8 Click Connector(V8)Body>Differential Wire / Frame Wire>Fuel Suction with Pump & Gage Tube Assemblyewd_type=component;type=c;code=V8;pinno=2,3 |
||
| V8-2(FE) - V8-3(FR) | Float position is F (upper) | Approximately 4.255 to 4.605 V* |
| V8-2(FE) - V8-3(FR) | Float position is E (lower) | Approximately 0.345 to 0.695V* |
*: The output voltage changes depending on the voltage applied to the terminals.
Output voltage (F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)
Output voltage (E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)
If the result is not as specified, replace the fuel sender gauge assembly.
83320B 2.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY
Check the No. 2 fuel sender gauge assembly output voltage.
| *a | Component without harness connected (No. 2 Fuel Sender Gauge Assembly) |
| *b | Voltage applied between terminals |
Apply 5 V between terminals 1 (FV2) and 2 (FE2).
Be careful when connecting the leads, as the No. 2 fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.
Do not apply more than 6 V to terminals 1 (FV2) and 2 (FE2).
If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.
| *a | Component without harness connected (No. 2 Fuel Sender Gauge Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(V10)Location & Routingewd_type=routing;type=c;code=V10 Click Connector(V10)Body>Differential Wire / Frame Wire>Fuel Pump (Fuel Tank Sub-Assembly)ewd_type=component;type=c;code=V10;pinno=2,3 |
||
| V10-2(FE2) - V10-3(FR2) | Float position is F (upper) | Approximately 4.255 to 4.605 V* |
| V10-2(FE2) - V10-3(FR2) | Float position is E (lower) | Approximately 0.345 to 0.695V* |
*: The output voltage changes depending on the voltage applied to the terminals.
Output voltage (F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)
Output voltage (E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)
If the result is not as specified, replace the No. 2 fuel sender gauge assembly.