DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Ptrl General / -
Ptrl AF Control / Air fuel ratio control system related data
Ptrl AF Control (D4) / Air fuel ratio control system related data (D4)
Ptrl AF O2 Sensor / Air fuel ratio sensors related data
Ptrl Throttle / Gasoline throttle system related data
Ptrl Intake Control / Intake control system related data
Ptrl Valve Control / Valve control system related data
Ptrl Misfire / "Misfire" related data
Ptrl Starting / "Difficult to start" related data
Ptrl Rough Idle / "Rough idle" related data
Ptrl Evaporative / Evaporative system related data
Ptrl CAT Converter / Catalyst converter related data
Flexible Fuel Vehicle / Flexible fuel vehicle related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transmission system related data
Vehicle Information / Vehicle information
Catalytic Converter / Catalyst converter related data
AF/O2 Sensor Operation (Banked) / Air fuel ratio control system related data
AF/O2 Sensor Operation (Inline) / Air fuel ratio control system related data
According to the display on the GTS, read the Data List.
The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all of the Data List items listed for that group will be displayed.
"Reference Value" is the assessment of one vehicle. Use it only for reference.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0 [km], Max.: 1677215 [km] | - | - |
| Total Distance Traveled - Unit | Total Distance Traveled unit | km or mile | - | - |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed |
·
This is the current vehicle speed.
·
The vehicle speed is detected using the wheel speed sensors.
-
There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the Freeze Frame Data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 600 to 800 rpm: Idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0%, Max.: 100% | - |
·
This is the engine load calculated based on the actual intake manifold pressure.
·
Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the actual intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Vehicle Load | Vehicle load | Min.: 0%, Max.: 25700% | Actual vehicle load |
·
This is the engine intake air charging efficiency.
·
Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow x 100 (%) Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)
|
| MAF Sensor Bank1 | Airflow rate from mass air flow meter sub-assembly (bank 1) | Min.: 0 gm/sec, Max.: 2047.96 gm/sec |
·
1.8 to 3.0 gm/sec: Idling (engine warmed up and shift lever in D)
·
5.0 to 25.0 gm/sec: 2000 rpm (without load)
·
6.5 to 30.0 gm/sec: 3000 rpm (without load) |
This is the intake air amount measured by the mass air flow meter sub-assembly (bank 1). |
| MAF Sensor Bank2 | Airflow rate from mass air flow meter sub-assembly (bank 2) | Min.: 0 gm/sec, Max.: 2047.96 gm/sec |
·
1.8 to 3.0 gm/sec: Idling (engine warmed up and shift lever in D)
·
5.0 to 25.0 gm/sec: 2000 rpm (without load)
·
6.5 to 30.0 gm/sec: 3000 rpm (without load) |
This is the intake air amount measured by the mass air flow meter sub-assembly (bank 2). |
| MAF Sensor Bank1 Supported | Status of the MAF Sensor Bank1 Supported | Supp or Unsupp | Supp | - |
| MAF Sensor Bank2 Supported | Status of the MAF Sensor Bank2 Supported | Supp or Unsupp | Supp | - |
| Atmospheric Pressure | Atmospheric pressure | Min.: 0 kPa (0 psi), Max.: 255 kPa (36.98 psi) | Equivalent to atmospheric pressure |
·
This value is calculated based on the atmospheric pressure sensor.
·
Standard atmospheric pressure: 101 kPa(abs) [14.65 psi(abs)]
·
For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (0.15 psi). This varies depending on the weather. |
| Intake Manifold Absolute Pressure | Intake manifold absolute pressure | Min.: 0 kPa (0 psi), Max.: 2047.96 kPa (296.95 psi) |
·
80 to 110 kPa (11.6 to 15.95 psi): Ignition switch ON
·
20 to 40 kPa (2.9 to 5.8 psi): Idling with warmed up engine |
This is the intake manifold pressure.
|
| Intake Manifold Absolute Pressure Supported | Status of the Intake Manifold Absolute Pressure Supported | Supp or Unsupp | Supp | - |
| Engine Oil Temperature Sensor | Engine oil temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | 80 to 110°C (176 to 230°F): After warming up | This is the engine oil temperature.
|
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Intake Air Temperature B1S1 (Turbo) | The intake air temperature after passing through the intercooler | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to temperature at location of No. 3 turbo pressure sensor | Indicates the intake air temperature after passing through the intercooler.
|
| Intake Air Temperature B1S1 (Turbo) Supported | Status of the Intake Air Temperature B1S1 (Turbo) Supported | Supp or Unsupp | Supp | - |
| Intake Air Temperature B1S2 (Turbo) Supported | Status of the Intake Air Temperature B1S2 (Turbo) Supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B1S1 | Intake air temperature (for bank 1 sensor 1) | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to temperature at location of mass air flow meter sub-assembly (bank 1) | This is the engine intake air temperature (bank 1).
|
| Intake Air Temperature B2S1 | Intake air temperature (for bank 2 sensor 1) | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to temperature at location of mass air flow meter sub-assembly (bank 2) | This is the engine intake air temperature (bank 2).
|
| Intake Air Temperature B1S1 Supported | Status of the Intake Air Temperature B1S1 Supported | Supp or Unsupp | Supp | - |
| Intake Air Temperature B1S2 Supported | Status of the Intake Air Temperature B1S2 Supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B1S3 Supported | Status of the Intake Air Temperature B1S3 Supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B2S1 Supported | Status of the Intake Air Temperature B2S1 Supported | Supp or Unsupp | Supp | - |
| Intake Air Temperature B2S2 Supported | Status of the Intake Air Temperature B2S2 Supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B2S3 Supported | Status of the Intake Air Temperature B2S3 Supported | Supp or Unsupp | Unsupp | - |
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to ambient temperature | This is the ambient temperature.
|
| Engine Run Time | Engine run time | Min.: 0 sec, Max.: 65535 sec | Time after engine start | This is the time elapsed since the engine was started. |
| IG-ON Coolant Temperature | Engine coolant temperature when the ignition switch is turned to ON | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the engine coolant temperature stored when the ignition switch is turned to ON. |
| Initial Engine Coolant Temperature | Engine coolant temperature when the engine is started | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the engine coolant temperature stored when the engine is started. |
| IG-ON Intake Air Temperature | Intake air temperature when the ignition switch is turned to ON | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the intake air temperature stored when the ignition switch is turned to ON. |
| Initial Engine Intake Air Temperature | Intake air temperature when the engine is started | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the intake air temperature stored when the engine is started. |
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.5 V | 11 to 14 V: Ignition switch ON | If 11 V or less, characteristics of some electrical components may change. |
| Battery Sensor Voltage | Battery sensor voltage | Min.: 0 V, Max.: 79.998 V | - | - |
| BATT Voltage | Battery voltage | Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON | If 11 V or less, characteristics of some electrical components may change. |
| IG2 / IGP | Status of IGP terminal | ON or OFF | ON: Ignition switch ON | - |
| IGR | Status of IGR terminal | ON or OFF | ON: Ignition switch ON | - |
| Glow Indicator Supported | Status of the Glow Indicator Supported | Supp or Unsupp | Unsupp | - |
| Engine Oil Pressure | Engine oil pressure | Min.: 0 kPa, Max.: 5119.921 kPa |
·
100 kPa or higher: 1500 rpm (engine oil temperature is 75 to 85°C [167 to 185°F])
·
200 kPa or higher: 2500 rpm (engine oil temperature is 75 to 85°C [167 to 185°F]) |
This is the engine oil pressure. |
Throttle Control (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Accelerator Position | Accelerator pedal position | Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%. |
| Accelerator Position Sensor No.1 Voltage % | Absolute No. 1 accelerator pedal position | Min.: 0%, Max.: 100% |
·
10 to 22%: Accelerator pedal fully released
·
52 to 90%: Accelerator pedal fully depressed |
The No. 1 accelerator pedal position sensor output is converted using 5 V = 100%.
|
| Accelerator Position Sensor No.2 Voltage % | Absolute No. 2 accelerator pedal position | Min.: 0%, Max.: 100% |
·
24 to 40%: Accelerator pedal fully released
·
68 to 95%: Accelerator pedal fully depressed |
The No. 2 accelerator pedal position sensor output is converted using 5 V = 100%. |
| Accelerator Position Sensor No.1 Voltage | No. 1 accelerator pedal position sensor voltage | Min.: 0 V, Max.: 4.98 V |
·
0.5 to 1.1 V: Accelerator pedal fully released
·
2.6 to 4.5 V: Accelerator pedal fully depressed |
This is the voltage output from the No. 1 accelerator pedal position sensor. |
| Accelerator Position Sensor No.2 Voltage | No. 2 accelerator pedal position sensor voltage | Min.: 0 V, Max.: 4.98 V |
·
1.2 to 2.0 V: Accelerator pedal fully released
·
3.4 to 4.75 V: Accelerator pedal fully depressed |
·
This is the voltage output from the No. 2 accelerator pedal position sensor.
·
The No. 2 accelerator pedal position sensor is used to monitor the No. 1 accelerator pedal position sensor. When there is a malfunction in the No. 1 accelerator pedal position sensor, the ECM uses the No. 2 accelerator pedal position sensor to control the engine. |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting released accelerator pedal | ON or OFF | ON: Accelerator pedal fully released | This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position. |
| Accelerator Position Sensor No.1 Fully Closed Learn Value | Accelerator fully released learned value (No. 1) | Min.: 0 deg, Max.: 124.5 deg | - | This is the value of No. 1 accelerator pedal position sensor learned when the accelerator pedal is released. |
| Accelerator Position Sensor No.2 Fully Closed Learn Value | Accelerator fully released learned value (No. 2) | Min.: 0 deg, Max.: 124.5 deg | - | This is the value of No. 2 accelerator pedal position sensor learned when the accelerator pedal is released. |
| Engine Starting Torque Control Count | Engine starting torque control count | Min.: 0, Max.: 255 | - | - |
| Throttle Position Sensor No.1 Voltage % | Absolute No. 1 throttle position sensor | Min.: 0%, Max.: 100% |
·
10 to 22%: Accelerator pedal fully released
·
64 to 96%: Accelerator pedal fully depressed (engine running) |
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Throttle Position Sensor No.2 Voltage % | Absolute No. 2 throttle position sensor | Min.: 0%, Max.: 100% |
·
42 to 62%: Accelerator pedal fully released
·
92 to 100%: Accelerator pedal fully depressed (engine running) |
The No. 2 throttle position sensor output is converted using 5 V = 100%. |
| System Guard | System guard | ON or OFF | ON: Idling or throttle actuator operating |
·
When there is a difference between the target and actual throttle valve opening angles, this item changes to OFF and the electronic throttle control system operation is disabled.
·
OFF: Electronic throttle control is stopped. |
| Open Side Malfunction | Open malfunction | ON or OFF | OFF | This item indicates a malfunction in the electronic throttle when the throttle valve is open. |
| Throttle Request Position | Required throttle position | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.1 V: Idling (A/C off and shift lever in P) | The value of this item is calculated by the ECM and shows the voltage for the target throttle valve position. |
| Throttle Sensor Position | Throttle sensor position | Min.: 0%, Max.: 100% |
·
0%: Accelerator pedal fully released
·
50 to 80%: Accelerator pedal fully depressed (engine running) |
·
This is the throttle valve opening amount used for engine control.
·
The value of this item has no meaning when the ignition switch is ON and the engine is not running.
·
The throttle valve opening amount during idle is indicated by 0%. |
| Throttle Position Sensor No.1 Voltage | No. 1 throttle position sensor output voltage | Min.: 0 V, Max.: 4.98 V |
·
0.6 to 1.1 V: Accelerator pedal fully released
·
3.2 to 4.8 V: Accelerator pedal fully depressed (engine running)
·
0.6 to 1.4 V: Fail-safe operating |
This is the No. 1 throttle position sensor output voltage. |
| Throttle Position Sensor No.2 Voltage | No. 2 throttle position sensor output voltage | Min.: 0 V, Max.: 4.98 V |
·
2.1 to 3.1 V: Accelerator pedal fully released
·
4.6 to 4.98 V: Accelerator pedal fully depressed (engine running)
·
2.1 to 3.1 V: Fail-safe operating |
This is the No. 2 throttle position sensor output voltage. |
| Throttle Position Command | Throttle position command value | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.1 V: Idling with warm engine (A/C off and shift lever in P) | The value displayed for this item is the same as Throttle Request Position. |
| Throttle Position Sensor Open Position No.1 | No. 1 throttle position sensor | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | This is the No. 1 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the ignition switch is ON. |
| Throttle Position Sensor Open Position No.2 | No. 2 throttle position sensor | Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | This is the No. 2 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the ignition switch is ON. |
| Throttle Motor Current | Throttle actuator current | Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling with warmed up engine (A/C off and shift lever in P) | When the value of this item is large but the actual opening angle (Throttle Position Sensor No.1 Voltage) does not reach the target opening angle (Throttle Request Position), there is an "unable to open" malfunction. |
| Throttle Motor Duty Ratio | Throttle actuator | Min.: 0%, Max.: 100% | 0 to 22%: Idling with warmed up engine (A/C off and shift lever in P) | This is the output duty ratio of the throttle actuator drive circuit. |
| Throttle Motor Duty Ratio (Open) | Throttle actuator duty ratio (open) | Min.: 0%, Max.: 255% | 0 to 40%: Idling with warmed up engine (A/C off and shift lever in P) | This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. |
| Throttle Motor Duty Ratio (Close) | Throttle actuator duty ratio (close) | Min.: 0%, Max.: 255% | 0 to 40%: Idling with warmed up engine (A/C off and shift lever in P) | This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
|
| Throttle Position Sensor Fully Closed Learn Value | Throttle valve fully closed position (learned value) | Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Ignition switch ON, accelerator pedal fully released |
·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. The ECM calculates the learned value based on the position of the throttle valve when the accelerator pedal is released and the throttle valve motor is not operating.
·
Learning is performed immediately after the ignition switch is turned to ON. |
| +BM Voltage | +BM voltage | Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON | This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P065714 (open or short circuit) and P06579E (ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off). |
| Actuator Power Supply | Actuator power supply | ON or OFF | ON: Idling or throttle actuator operating | - |
| Throttle Air Flow Learn Value (Area 1) | Throttle air flow learning value of area 1 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Area 2) | Throttle air flow learning value of area 2 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Area 3) | Throttle air flow learning value of area 3 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Calculated Value) | Throttle air flow learning value (calculated value) | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Atmosphere Pressure Offset Value) | Throttle air flow learning value (atmosphere pressure offset value) | Min.: 0, Max.: 2.55 | - | - |
Turbocharger Control 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wastegate Valve Control Duty Ratio Bank2 | Waste gate valve (bank 2) control duty ratio | Min.: -200%, Max.: 199.99% | -100 to 100% | - |
| Wastegate Valve Control Duty Ratio Bank1 | Waste gate valve (bank 1) control duty ratio | Min.: -200%, Max.: 199.99% | -100 to 100% | - |
| Wastegate Valve Sensor Voltage when Fully Closed Bank1 | Sensor voltage (bank 1) when the waste gate valve is fully closed | Min.: 0 V, Max.: 4.999 V | 3.305 to 4.364 V |
·
This is the value when the waste gate valve is fully closed during waste gate valve active detection.
·
The ECM performs waste gate valve active detection when the accelerator pedal is fully released while the vehicle is stopped after warming up the engine.
·
"Waste gate valve active detection" is when the ECM forcibly operates the waste gate valve to the open side for 3 seconds and to the closed side for 3 seconds, for a total of 6 seconds. At this time, the fully open and fully closed output voltage and the voltage change amount are monitored and malfunctions are detected.
·
This value is updated during waste gate valve active detection and is not cleared. |
| Wastegate Valve Sensor Voltage when Fully Closed Bank2 | Sensor voltage (bank 2) when the waste gate valve is fully closed | Min.: 0 V, Max.: 4.999 V | 3.305 to 4.368 V |
·
This is the value when the waste gate valve is fully closed during waste gate valve active detection.
·
The ECM performs waste gate valve active detection when the accelerator pedal is fully released while the vehicle is stopped after warming up the engine.
·
"Waste gate valve active detection" is when the ECM forcibly operates the waste gate valve to the open side for 3 seconds and to the closed side for 3 seconds, for a total of 6 seconds. At this time, the fully open and fully closed output voltage and the voltage change amount are monitored and malfunctions are detected.
·
This value is updated during waste gate valve active detection and is not cleared. |
| Wastegate Valve Sensor Voltage when Fully Open Bank1 | Sensor voltage (bank 1) when the waste gate valve is fully open | Min.: 0 V, Max.: 4.999 V | 0.826 to 1.337 V |
·
This is the value when the waste gate valve is fully closed during waste gate valve active detection.
·
The ECM performs waste gate valve active detection when the accelerator pedal is fully released while the vehicle is stopped after warming up the engine.
·
"Waste gate valve active detection" is when the ECM forcibly operates the waste gate valve to the open side for 3 seconds and to the closed side for 3 seconds, for a total of 6 seconds. At this time, the fully open and fully closed output voltage and the voltage change amount are monitored and malfunctions are detected.
·
This value is updated during waste gate valve active detection and is not cleared. |
| Wastegate Valve Sensor Voltage when Fully Open Bank2 | Sensor voltage (bank 2) when the waste gate valve is fully open | Min.: 0 V, Max.: 4.999 V | 0.826 to 1.339 V |
·
This is the value when the waste gate valve is fully closed during waste gate valve active detection.
·
The ECM performs waste gate valve active detection when the accelerator pedal is fully released while the vehicle is stopped after warming up the engine.
·
"Waste gate valve active detection" is when the ECM forcibly operates the waste gate valve to the open side for 3 seconds and to the closed side for 3 seconds, for a total of 6 seconds. At this time, the fully open and fully closed output voltage and the voltage change amount are monitored and malfunctions are detected.
·
This value is updated during waste gate valve active detection and is not cleared. |
| Wastegate Valve Actuator Current Bank1 | Waste gate valve drive motor (bank 1) current | Min.: -32.768 A, Max.: 32.767 A | -1.3 to 1.3 A | - |
| Wastegate Valve Actuator Current Bank2 | Waste gate valve drive motor (bank 2) current | Min.: -32.768 A, Max.: 32.767 A | -1.3 to 1.3 A | - |
| Wastegate Valve Position Bank1 | Waste gate valve (bank 1) opening amount | Min.: 0 deg, Max.: 499.99 deg | 13.15 to 32.86 deg: fully closed 97.83 to 104.87 deg: fully open |
- |
| Wastegate Valve Position Bank2 | Waste gate valve (bank 2) opening amount | Min.: 0 deg, Max.: 499.99 deg | 13.15 to 32.86 deg: fully closed 97.83 to 104.87 deg: fully open |
- |
| Wastegate Valve Failure Mode Bank1 | Waste gate valve malfunction mode (bank 1) | Normal, Abnormal, Fully Closed, Fully Open, Malfunction or Internal Components Missing | Normal |
·
Abnormal: Waste gate valve may be malfunctioning
·
Fully Closed: Waste gate valve may be stuck at fully closed position
·
Fully Open: Waste gate valve may be stuck at fully open position
·
Malfunction: Waste gate valve operations may be defective
·
Components Missing: Waste gate valve components may be missing |
| Wastegate Valve Failure Mode Bank2 | Waste gate valve malfunction mode (bank 2) | Normal, Abnormal, Fully Closed, Fully Open, Malfunction or Internal Components Missing | Normal |
·
Abnormal: Waste gate valve may be malfunctioning
·
Fully Closed: Waste gate valve may be stuck at fully closed position
·
Fully Open: Waste gate valve may be stuck at fully open position
·
Malfunction: Waste gate valve operations may be defective
·
Components Missing: Waste gate valve components may be missing |
| Turbocharger/Supercharger Inlet Pressure Bank1 | Compressor inlet pressure value (bank 1) | Min.: 0 kPa, Max.: 655.35 kPa | Atmospheric pressure +/-5 kPa: Ignition switch ON |
·
At ignition switch ON, the Turbocharger/Supercharger Inlet Pressure Bank1 approximately equals the atmospheric pressure (standard atmospheric pressure is 101 kPa [14.65 psi]).
·
The compressor inlet pressure value is the output value of the No. 1 turbo pressure sensor.
·
At ignition switch ON, the Turbocharger/Supercharger Inlet Pressure Bank1, Turbocharger/Supercharger Inlet Pressure Bank2 and Boost Pressure Sensor are approximately equal. |
| Turbocharger/Supercharger Inlet Pressure Bank2 | Compressor inlet pressure value (bank 2) | Min.: 0 kPa, Max.: 655.35 kPa | Atmospheric pressure +/-5 kPa: Ignition switch ON |
·
At ignition switch ON, the Turbocharger/Supercharger Inlet Pressure Bank2 approximately equals the atmospheric pressure (standard atmospheric pressure is 101 kPa [14.65 psi]).
·
The compressor inlet pressure value is the output value of the No. 1 turbo pressure sensor.
·
At ignition switch ON, the Turbocharger/Supercharger Inlet Pressure Bank1, Turbocharger/Supercharger Inlet Pressure Bank2 and Boost Pressure Sensor are approximately equal. |
Idle Speed Control (Ptrl Rough Idle)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Low Revolution Control | Low engine speed control operation state | ON or OFF | OFF | This item indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This item changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (if the A/C switch is on, the engine speed thresholds below are increased by 100 to 200 rpm).
·
900 rpm (when the engine coolant temperature is 10°C [50°F])
·
850 rpm (when the engine coolant temperature is 30°C [86°F])
·
750 rpm (when the engine coolant temperature is 60°C [140°F]) Before 5 seconds have elapsed since the engine was started, this item indicates the status of the previous trip. After 5 seconds have elapsed since the engine was started, this item indicates the status of the current trip.
|
| Neutral Control | Neutral control status | ON or OFF | OFF: Idling, shift lever in P | - |
| N Range Status | Shift N position status | ON or OFF | ON: Shift lever in P or N | - |
| Engine Stall Control F/B Flow | ISC torque lower limit value to prevent engine stall | Min.: -1024 Nm, Max.: 1023.96 Nm | - | The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent the engine from stalling. |
| ISC F/B Learn Torque | ISC feedback learning torque | Min.: -1024 Nm, Max.: 1023.96 Nm | - | This item represents compensation value necessary to make the engine run at the target idle speed. This value expresses the difference between the actual torque and estimated torque. For example, when this value is positive, maintaining the idle speed requires more torque than the estimated torque.
|
| ISC Total AUXS Torque | ISC total AUXS torque | Min.: -1024 Nm, Max.: 1023.96 Nm | 8 to 70 Nm: Idling (engine warmed up, A/C off and shift lever in P) | This item represents the total of each estimated load torque when the engine is idling. (The total load torque of engine friction, alternator, air conditioner, A/T, etc.) |
| ISC F/B Torque | ISC feedback torque | Min.: -1024 Nm, Max.: 1023.96 Nm | -10 to 10 Nm: Idling (engine warmed up, A/C off and shift lever in P) | This item expresses the feedback compensation value (torque) necessary to make the engine run at the target idle speed.
|
| Sum of ISC F/B Torque (Recent) | ISC feedback torque (recent) | Min.: -1024 Nm, Max.: 1023.96 Nm | -5 to 5 Nm: Idling (engine warmed up, A/C off and shift lever in P) | This item expresses the feedback compensation value (torque) necessary to make the engine quickly match the target idle speed.
|
| ISC AUXS Torque (Alternator) | ISC AUXS torque (alternator) | Min.: -1024 Nm, Max.: 1023.96 Nm | 0 to 30 Nm: Idling (engine warmed up, A/C off and shift lever in P) | This item expresses the ISC compensation amount (estimated torque) according to the alternator load. |
| ISC AUXS Torque (Air Conditioner) | ISC AUXS torque (air conditioner) | Min.: -1024 Nm, Max.: 1023.96 Nm | 5 to 55.5 Nm: Idling (engine warmed up, A/C on and shift lever in P) | This item expresses the ISC compensation torque (estimated torque) according to the air conditioner compressor load. |
| Throttle Air Flow F/B Value | Throttle air flow feedback value | Min.: -4096000 L/s, Max.: 4095875 L/s | - | This item expresses the throttle air flow feedback value. |
| Throttle Position | Throttle position | Min.: 0 deg, Max.: 499.99 deg | - | - |
Fuel System 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Fuel Pressure (High) | Target fuel pressure (for high pressure side) | Min.: 0 kPa, Max.: 655350 kPa | 2800 to 20000 kPag: 3000 rpm (warmed up engine, A/C off and shift lever in P) | This item indicates the target fuel pressure for the fuel pump assembly (for high pressure side). |
| Target Fuel Pressure (High) Supported | Status of the Target Fuel Pressure (High) Supported | Supp or Unsupp | Supp | - |
| Target Fuel Pressure (Low) / Target Fuel Pressure 2 | Target fuel pressure (for low pressure side) | Min.: 0 kPa, Max.: 655350 kPa | 300 to 644 kPag | This item indicates the target fuel pressure for the fuel pump assembly (for low pressure side). |
| Target Fuel Pressure (Low) / Target Fuel Pressure 2 Supported | Status of the Target Fuel Pressure (Low) Supported | Supp or Unsupp | Supp | - |
| Fuel Pressure (High) | Fuel pressure (for high pressure side) | Min.: 0 kPa, Max.: 655350 kPa | 2800 to 20000 kPag: 3000 rpm (warmed up engine, A/C off and shift lever in P) | This item indicates the fuel pressure (for high pressure side). |
| Fuel Pressure (High) Supported | Status of the Fuel Pressure (High) Supported | Supp or Unsupp | Supp | - |
| Fuel Pressure (Low) / Fuel Pressure 2 | Fuel pressure (for low pressure side) | Min.: 0 kPa, Max.: 655350 kPa | 300 to 644 kPag | This item indicates the fuel pressure (for low pressure side). |
| Fuel Pressure (Low) / Fuel Pressure 2 Supported | Status of the Fuel Pressure (Low) Supported | Supp or Unsupp | Supp | - |
Fuel System 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Pump Target Speed | Fuel pump target speed (for low pressure side) | -32768 to 32767 rpm | - | - |
| Fuel Pump F/B Offset | Feedback compensation level of the fuel pump (low pressure side) | -327.68 to 327.67 L/h | - | - |
| Fuel Pump Control Duty Ratio | Fuel pump duty ratio (for low pressure side) | Min.: 0%, Max.: 399.9% | - | This item indicates the duty ratio of the fuel pump assembly (for low pressure side). |
| Low Pressure Fuel Delivery Internal Temperature | Low pressure fuel delivery internal temperature | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | The fuel temperature is estimated from the engine speed, water temperature, intake air temperature and fuel flow rate. |
| Injector Cylinder #1 (Port) | Injection period of the No. 1 cylinder (port injection) | Min.: 0 μs, Max.: 65535 μs | 700 to 6000 μs: Idling with warmed up engine, port injection control |
·
This is the injection period of the No. 1 cylinder (port injection) (the command value from the ECM).
·
The latest injection timing may be displayed even when fuel injection is not performed. Confirm the injection status by also referring to the Data List item "Injection Mode". |
| Injection Volume Cylinder #1 | Injection volume (cylinder 1) | Min.: 0 ml, Max.: 2 ml | 0.05 to 0.15 ml: Idling with warmed up engine, port injection control | This is the fuel injection volume for 10 injections. |
| Target Fuel Pressure Offset | Target fuel pressure offset | Min.: -25%, Max.: 24.8% | - |
·
Active Test item [Control the Target Fuel Pressure Offset] support data.
·
0 is displayed when the Active Test is not being performed. |
| Injection Volume | Injection volume | Min.: -25%, Max.: 24.8% | - |
·
Active Test item [Control the Injection Volume] or [Control the Injection Volume for A/F Sensor] support data.
·
0 is displayed when the Active Test is not being performed. |
| Engine Fuel Rate | Engine fuel consumption | Min.: 0 gm/sec, Max.: 1310.7 gm/sec | - | - |
| Vehicle Fuel Rate | Vehicle fuel consumption | Min.: 0 gm/sec, Max.: 1310.7 gm/sec | - | - |
| Low Fuel Pressure Sensor | No. 2 fuel pressure sensor (for low pressure side) output | Min.: -3276.8 kPag, Max.: 3276.7 kPag | 300 to 644 kPag | This item indicates the fuel pressure (for low pressure side) from the No. 2 fuel pressure sensor (for low pressure side). |
| High Fuel Pressure Sensor | Fuel pressure sensor (for high pressure side) output | Min.: -64 MPa, Max.: 63.998 MPa | 2.8 to 20 MPa | This item indicates the fuel pressure (for high pressure side) from the fuel pressure sensor (for high pressure side). |
| High Pressure Fuel Pump Duty Ratio (D4) | Fuel pump (bank 1) duty ratio (for high pressure side) | Min.: 0%, Max.: 127.5% | 0 to 50%: Idling (A/C off) | This item indicates the duty ratio of the electromagnetic spill valve (bank 1). |
| High Pressure Fuel Pump Discharge Rate | Fuel volume required by the high pressure fuel pump (bank 1) | Min.: 0 ml, Max.: 2 ml | - | This item indicates the fuel pump assembly (for high pressure side) discharge amount. |
| High Pressure Fuel Pump Internal Temperature | High pressure fuel pump internal temperature | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | Estimate fuel temperature from engine speed, water temperature, intake air temperature and fuel flow rate. |
| Injection Mode | Injection mode | Port / Direct / Either | - | This item indicates the injection mode. |
| Injection Switching Status | Prohibition of changing the D-4S injection method | OK or NG | - | This item indicates whether the Control the Injection Mode Active Test is prohibited. |
| Injection Timing Cylinder #1 (D4) | Injection timing (for direct injection) | Min.: -3276.8 deg(CA), Max.:3276.7 deg(CA) | 240 to 360 deg(CA): Idling (warmed up engine, A/C off and shift lever in P), direct injection control | This item indicates the injection timing of the No. 1 direct fuel injector assembly. |
| Injection Time Cylinder #1 (D4) | Injection time (for direct injection) | Min.: 0 μs, Max.: 65535 μs | 700 to 2300 μs: Idling (warmed up engine, A/C off and shift lever in P), direct injection control |
·
This item indicates the last injection time of the No. 1 direct fuel injector assembly.
·
The latest injection timing may be displayed even when fuel injection is not performed. Confirm the injection status by also referring to the Data List item "Injection Mode". |
| Current Fuel Type | Current fuel type | - | Gasoline/petrol | - |
EVAP System (Ptrl Evaporative)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| EVAP (Purge) VSV | Purge VSV control duty | Min.: 0%, Max.: 100% | - |
·
This is the command signal from the ECM.
·
This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed. *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV.
·
When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV will be 0%. |
| EVAP Purge Flow | Purge flow | Min.: 0%, Max.: 399.9% | - | This is the percentage of total engine airflow contributed by EVAP purge operation. (Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) |
| EVAP Purge Density Learn Value | Purge density learned value | Min.: -200, Max.: 199.993 | - |
·
This is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate.
·
When the value of this item is a large negative value, the purge effect is large.
·
The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced.
·
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
|
| EVAP Purge VSV | VSV status for EVAP control | ON or OFF | - | This item is ON when EVAP (Purge) VSV is approximately 30% or higher, and is OFF when the VSV duty ratio is less than 30%. |
| Purge Cut VSV Duty | Purge VSV duty | Min.: 0%, Max.: 399.9% | - | - |
Air Fuel Ratio Control (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Air-Fuel Ratio | Target air fuel ratio | Min.: 0, Max.: 2 | 0.8 to 1.2: During idling (engine warmed up) |
·
This is the target air fuel ratio used by the ECM.
·
1.0 is the stoichiometric air fuel ratio. Values that are more than 1.0 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1.0 indicate the system attempting to make the air fuel ratio richer. |
| A/F (O2) Lambda Sensor B1S1 | Output air fuel ratio associated with bank 1 sensor 1 | Min.: 0, Max.: 1.99 |
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean |
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
| A/F (O2) Lambda Sensor B2S1 | Output air fuel ratio associated with bank 2 sensor 1 | Min.: 0, Max.: 1.99 |
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean |
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
| A/F (O2) Lambda Sensor B1S2 | Output air fuel ratio associated with bank 1 sensor 2 | Min.: 0, Max.: 1.99 |
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean |
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
| A/F (O2) Lambda Sensor B2S2 | Output air fuel ratio associated with bank 2 sensor 2 | Min.: 0, Max.: 1.99 |
·
Value less than 1 (0.000 to 0.999) = Rich
·
1 = Stoichiometric air fuel ratio
·
Value more than 1 (1.001 to 1.999) = Lean |
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
| A/F (O2) Sensor Current B1S1 | Air fuel ratio sensor (bank 1 sensor 1) output current | Min.: -128 mA, Max.: 127.996 mA | -0.5 to 0.5 mA: Idling (engine warmed up) |
·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor (bank 1 sensor 1) current output is approximately -0.5 to 0.5 mA.
·
When the value is outside the range of 0.47 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor (bank 1 sensor 1) or sensor circuit.
·
Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output current of the sensor. |
| A/F (O2) Sensor Current B2S1 | Air fuel ratio sensor (bank 2 sensor 1) output current | Min.: -128 mA, Max.: 127.996 mA | -0.5 to 0.5 mA: Idling (engine warmed up) |
·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor (bank 2 sensor 1) current output is approximately -0.5 to 0.5 mA.
·
When the value is outside the range of 0.47 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor (bank 2 sensor 1) or sensor circuit.
·
Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output current of the sensor. |
| A/F (O2) Sensor Current B1S2 | Air fuel ratio sensor (bank 1 sensor 2) output current | Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling (engine warmed up) |
·
A/F (O2) Sensor Current B1S2 display is less than 0 mA: Richer than the stoichiometric air-fuel ratio
·
A/F (O2) Sensor Current B1S2 display is more than 0 mA: Leaner than stoichiometric air-fuel ratio
·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor (bank 1 sensor 2) current output is approximately -0.5 to 0.5 mA.
·
When the value is outside the range of 7.5 to 33.13 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor (bank 1 sensor 2) or sensor circuit.
·
Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output current of the sensor. |
| A/F (O2) Sensor Current B2S2 | Air fuel ratio sensor (bank 1 sensor 2) output current | Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling (engine warmed up) |
·
A/F (O2) Sensor Current B2S2 display is less than 0 mA: Richer than the stoichiometric air-fuel ratio
·
A/F (O2) Sensor Current B2S2 display is more than 0 mA: Leaner than stoichiometric air-fuel ratio
·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor (bank 2 sensor 2) current output is approximately -0.5 to 0.5 mA.
·
When the value is outside the range of 7.5 to 33.13 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor (bank 2 sensor 2) or sensor circuit.
·
Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output current of the sensor. |
| A/F (O2) Sensor Heater Duty Ratio B1S1 | Air fuel ratio sensor (bank 1 sensor 1) heater duty ratio | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | When the value is any value except 0%, current is being supplied to the heater. |
| A/F (O2) Sensor Heater Duty Ratio B2S1 | Air fuel ratio sensor (bank 2 sensor 1) heater duty ratio | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | When the value is any value except 0%, current is being supplied to the heater. |
| A/F Sensor Heater Current Value B1S2 | Air fuel ratio sensor (bank 1 sensor 2) heater current | Min.: 0 A, Max.: 65.535 A | - | When the value is any value except 0 A, current is being supplied to the heater. |
| A/F Sensor Heater Current Value B2S2 | Air fuel ratio sensor (bank 2 sensor 2) heater current | Min.: 0 A, Max.: 65.535 A | - | When the value is any value except 0 A, current is being supplied to the heater. |
| A/F Sensor Heater Duty B1S2 | Air fuel ratio sensor (bank 1 sensor 2) heater duty ratio | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | When the value is any value except 0%, current is being supplied to the heater. |
| A/F Sensor Heater Duty B2S2 | Air fuel ratio sensor (bank 2 sensor 2) heater duty ratio | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | When the value is any value except 0%, current is being supplied to the heater. |
| A/F Sensor Impedance B1S1 | Air fuel ratio sensor (bank 1 sensor 1) impedance | Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm: Idling (engine warmed up) | - |
| A/F Sensor Impedance B2S1 | Air fuel ratio sensor (bank 2 sensor 1) impedance | Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm: Idling (engine warmed up) | - |
| A/F Sensor Impedance B1S2 | Air fuel ratio sensor (bank 1 sensor 2) impedance | Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm: Idling (engine warmed up) | - |
| A/F Sensor Impedance B2S2 | Air fuel ratio sensor (bank 2 sensor 2) impedance | Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm: Idling (engine warmed up) | - |
| A/F (O2) Sensor +Terminal Voltage Bank 1 | Air fuel ratio sensor (bank 1 sensor 1) positive terminal voltage | Min.: 0 V, Max.: 79.998 V | - | - |
| A/F (O2) Sensor +Terminal Voltage Bank 2 | Air fuel ratio sensor (bank 2 sensor 1) positive terminal voltage | Min.: 0 V, Max.: 79.998 V | - | - |
| A/F (O2) Sensor -Terminal Voltage Bank 1 | Air fuel ratio sensor (bank 1 sensor 1) negative terminal voltage | Min.: 0 V, Max.: 79.998 V | - | - |
| A/F (O2) Sensor -Terminal Voltage Bank 2 | Air fuel ratio sensor (bank 2 sensor 1) negative terminal voltage | Min.: 0 V, Max.: 79.998 V | - | - |
| A/F (O2) Sensor Heater Control Duty Ratio Bank1 | Air fuel ratio sensor (bank 1 sensor 1) heater control duty ratio | Min.: -327.68%, Max.: 327.67% | - |
·
Indicates the air fuel ratio sensor heater duty ratio requested by the ECM.
·
When normal, shows the same value as the A/F (O2) Sensor Heater Output Duty Ratio Bank1.
·
When the value of "A/F Sensor Heater Control Duty Ratio Bank1" is other than 0% and the value of "A/F Sensor Heater Output Duty Ratio Bank1" is 0%, the heater operation has stopped due to a malfunction in the air fuel ratio sensor. |
| A/F (O2) Sensor Heater Control Duty Ratio Bank2 | Air fuel ratio sensor (bank 2 sensor 1) heater control duty ratio | Min.: -327.68%, Max.: 327.67% | - |
·
Indicates the air fuel ratio sensor heater duty ratio requested by the ECM.
·
When normal, shows the same value as the A/F (O2) Sensor Heater Output Duty Ratio Bank2.
·
When the value of "A/F Sensor Heater Control Duty Ratio Bank2" is other than 0% and the value of "A/F Sensor Heater Output Duty Ratio Bank2" is 0%, the heater operation has stopped due to a malfunction in the air fuel ratio sensor. |
| A/F (O2) Sensor Heater Output Duty Ratio Bank1 | Air fuel ratio sensor (bank 1 sensor 1) heater output duty ratio | Min.: 0%, Max.: 399.99% | - |
·
Indicates the air fuel ratio sensor heater duty ratio that is actually being output.
·
When normal, shows the same value as the A/F (O2) Sensor Heater Output Duty Ratio Bank1.
·
When the value of "A/F Sensor Heater Control Duty Ratio Bank1" is other than 0% and the value of "A/F Sensor Heater Output Duty Ratio Bank1" is 0%, the heater operation has stopped due to a malfunction in the air fuel ratio sensor. |
| A/F (O2) Sensor Heater Output Duty Ratio Bank2 | Air fuel ratio sensor (bank 2 sensor 1) heater output duty ratio | Min.: 0%, Max.: 399.99% | - |
·
Indicates the air fuel ratio sensor heater duty ratio that is actually being output.
·
When normal, shows the same value as the A/F (O2) Sensor Heater Output Duty Ratio Bank2.
·
When the value of "A/F Sensor Heater Control Duty Ratio Bank2" is other than 0% and the value of "A/F Sensor Heater Output Duty Ratio Bank2" is 0%, the heater operation has stopped due to a malfunction in the air fuel ratio sensor. |
| A/F (O2) Sensor Heater ON Current Value Bank1 | Air fuel ratio sensor (bank 1 sensor 1) heater on current value | Min.: 0 A, Max.: 65.535 A | -0.5 to 0.5 mA: Idling (engine warmed up) | - |
| A/F (O2) Sensor Heater ON Current Value Bank2 | Air fuel ratio sensor (bank 2 sensor 1) heater on current value | Min.: 0 A, Max.: 65.535 A | -0.5 to 0.5 mA: Idling (engine warmed up) | - |
| A/F (O2) Sensor Heater Current-Carrying Status Bank1 (at Heater OFF) | Air fuel ratio sensor (bank 1 sensor 1) carrying status (at heater off) | ON or OFF | OFF: Ignition switch ON | - |
| A/F (O2) Sensor Heater Current-Carrying Status Bank2 (at Heater OFF) | Air fuel ratio sensor (bank 2 sensor 1) carrying status (at heater off) | ON or OFF | OFF: Ignition switch ON | - |
| A/F (O2) Sensor Heater Overcurrent Bank1 | Air fuel ratio sensor (bank 1 sensor 1) heater overcurrent | OFF or ON | OFF | - |
| A/F (O2) Sensor Heater Overcurrent Bank2 | Air fuel ratio sensor (bank 2 sensor 1) heater overcurrent | OFF or ON | OFF | - |
| A/F (O2) Sensor Heater Control Run Time Bank1 | Air fuel ratio sensor (bank 1 sensor 1) heater control run time | Min.: 0 ms, Max.: 65535 ms | - | - |
| A/F (O2) Sensor Heater Control Run Time Bank2 | Air fuel ratio sensor (bank 2 sensor 1) heater control run time | Min.: 0 ms, Max.: 65535 ms | - | - |
| Short FT B1S1 | Short-term fuel trim (bank 1 sensor 1) | Min.: -100%, Max.: 99.21% | -20 to 20% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor (bank 1 sensor 1) for feedback. |
| Short FT B2S1 | Short-term fuel trim (bank 2 sensor 1) | Min.: -100%, Max.: 99.21% | -20 to 20% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor (bank 2 sensor 1) for feedback. |
| Short FT B1S2 | Short-term fuel trim (bank 1 sensor 2) | Min.: -100%, Max.: 99.21% | -10 to 10% (Coolant Temperature 80°C (176°F) or higher) | Maintains the air-fuel ratio at the stoichiometric air-fuel ratio by making minor adjustments to the target air-fuel ratio for the air-fuel ratio calibration during normal driving.
|
| Short FT B2S2 | Short-term fuel trim (bank 2 sensor 2) | Min.: -100%, Max.: 99.21% | -10 to 10% (Coolant Temperature 80°C (176°F) or higher) | Maintains the air-fuel ratio at the stoichiometric air-fuel ratio by making minor adjustments to the target air-fuel ratio for the air-fuel ratio calibration during normal driving.
|
| Long FT B1S1 | Long-term fuel trim (bank 1 sensor 1) | Min.: -100%, Max.: 99.21% | -20 to 20% |
·
The ECM will learn the Long FT B1S1 values based on Short FT B1S1. The goal is to keep Short FT B1S1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.
·
This item is used to determine whether the system related to air fuel ratio control is malfunctioning.
·
The condition of the system is determined based on the sum of Short FT B1S1 and Long FT B1S1 (excluding times when the system is in transition).
-
20% or higher: The air fuel ratio may be lean.
-
-20 to 20%: The air fuel ratio can be determined to be normal.
-
-20% or less: The air fuel ratio may be rich.
-
Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT B1S1" indicates the learned value for the current operating range. [A/F Learn Value Idle Bank 1], [A/F Learn Value Low Bank 1], [A/F Learn Value Mid No.1 Bank 1], [A/F Learn Value Mid No.2 Bank 1], [A/F Learn Value High Bank 1], [A/F Learn Value Idle (Port) Bank 1], [A/F Learn Value Low (Port) Bank 1], [A/F Learn Value Mid No.1 (Port) Bank 1], [A/F Learn Value Mid No.2 (Port) Bank 1] and [A/F Learn Value High (Port) Bank 1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT B1S1" indicates the current engine operating range. |
| Long FT B2S1 | Long-term fuel trim (bank 2 sensor 1) | Min.: -100%, Max.: 99.21% | -20 to 20% |
·
The ECM will learn the Long FT B2S1 values based on Short FT B2S1. The goal is to keep Short FT B2S1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.
·
This item is used to determine whether the system related to air fuel ratio control is malfunctioning.
·
The condition of the system is determined based on the sum of Short FT B2S1 and Long FT B2S1 (excluding times when the system is in transition).
-
20% or higher: The air fuel ratio may be lean.
-
-20 to 20%: The air fuel ratio can be determined to be normal.
-
-20% or less: The air fuel ratio may be rich.
-
Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT B2S1" indicates the learned value for the current operating range. [A/F Learn Value Idle Bank 2], [A/F Learn Value Low Bank 2], [A/F Learn Value Mid No.1 Bank 2], [A/F Learn Value Mid No.2 Bank 2], [A/F Learn Value High Bank 2], [A/F Learn Value Idle (Port) Bank 2], [A/F Learn Value Low (Port) Bank 2], [A/F Learn Value Mid No.1 (Port) Bank 2], [A/F Learn Value Mid No.2 (Port) Bank 2] and [A/F Learn Value High (Port) Bank 2] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT B2S1" indicates the current engine operating range. |
| Long FT B1S2 | Long-term fuel trim (bank 1 sensor 2) | Min.: -100%, Max.: 99.21% | -2 to 1% | Learns and records the air-fuel ratio feedback value for "Short FT B1S2".
|
| Long FT B2S2 | Long-term fuel trim (bank 2 sensor 2) | Min.: -100%, Max.: 99.21% | -2 to 1% | Learns and records the air-fuel ratio feedback value for "Short FT B2S2".
|
| Total FT Bank 1 | Total fuel trim (bank 1) | Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling with warm engine | Total FT Bank 1 = Short FT B1S1 + Long FT B1S1 |
| Total FT Bank 2 | Total fuel trim (bank 2) | Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling with warm engine | Total FT Bank 2 = Short FT B2S1 + Long FT B2S1 |
| Fuel System Status Bank 1 | Fuel system status (bank 1) | Unused, OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Feedback for fuel control.
·
OLDrive: Open loop due to driving conditions (fuel enrichment).
·
OLFault: Open loop due to a detected system fault.
·
CLFault: Closed loop but the air fuel ratio sensor (sensor 1), which is used for fuel control, is malfunctioning. |
| Fuel System Status Bank 2 | Fuel system status (bank 2) | Unused, OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
·
CL (Closed Loop): Feedback for fuel control.
·
OLDrive: Open loop due to driving conditions (fuel enrichment).
·
OLFault: Open loop due to a detected system fault.
·
CLFault: Closed loop but the air fuel ratio sensor (sensor 2), which is used for fuel control, is malfunctioning. |
| A/F Learn Value Idle (Port) Bank 1 | Air fuel ratio learn value of idle area (port) for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Idle (Port) Bank 2 | Air fuel ratio learn value of idle area (port) for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low (Port) Bank 1 | Air fuel ratio learn value of low load area (port) for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts) |
| A/F Learn Value Low (Port) Bank 2 | Air fuel ratio learn value of low load area (port) for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts) |
| A/F Learn Value Mid No.1 (Port) Bank 1 | Air fuel ratio learn value of middle1 load area (port) for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.1 (Port) Bank 2 | Air fuel ratio learn value of middle1 load area (port) for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.2 (Port) Bank 1 | Air fuel ratio learn value of middle2 load area (port) for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.2 (Port) Bank 2 | Air fuel ratio learn value of middle2 load area (port) for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High (Port) Bank 1 | Air fuel ratio learn value of high load area (port) for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High (Port) Bank 2 | Air fuel ratio learn value of high load area (port) for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Idle Bank 1 | Air fuel ratio learn value of idle area for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Idle Bank 2 | Air fuel ratio learn value of idle area for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low Bank 1 | Air fuel ratio learn value of low load area for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Low Bank 2 | Air fuel ratio learn value of low load area for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.1 Bank 1 | Air fuel ratio learn value of middle1 load area for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.1 Bank 2 | Air fuel ratio learn value of middle1 load area for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.2 Bank 1 | Air fuel ratio learn value of middle2 load area for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.2 Bank 2 | Air fuel ratio learn value of middle2 load area for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High Bank 1 | Air fuel ratio learn value of high load area for bank 1 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High Bank 2 | Air fuel ratio learn value of high load area for bank 2 | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
Ignition System (Ignition)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Timing Cylinder #1 | Ignition timing advance for No. 1 cylinder | Min.: -64 deg, Max.: 63.5 deg | 8 to 25 deg: Idling (engine warmed up, A/C off and shift lever in N) | - |
| Knock F/B Value | Knocking feedback value | Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | -17 to 0 deg(CA): Driving at 70 km/h (43 mph) | This is the ignition timing retard compensation amount determined by the presence or absence of knocking. Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock F/B Value*3 + each compensation amount Example: 21 deg(CA) = 10 deg(CA) + 14 deg(CA) - 3 deg(CA) *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock F/B Value as close to -3 deg(CA) as possible. When Knock F/B Value is less than -4 deg(CA), Knock Correct Learn Value is slowly decreased. When Knock F/B Value is higher than -2 deg(CA), Knock Correct Learn Value is slowly increased. *3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.
|
| Knock Correct Learn Value | Knocking correction learned value | Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | - |
·
Refer to "Knock F/B Value".
·
When there is knocking or a lack of power, compare the values of following items to another vehicle of the same model.
-
Engine Speed
-
Calculate Load
-
Ignition Timing Cylinder #1
-
Knock F/B Value
-
Knock Correct Learn Value
·
Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced.
·
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
|
| Idle Spark Advance Control Cylinder #1 | Individual cylinder timing advance compensation amount (No. 1) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #2 | Individual cylinder timing advance compensation amount (No. 2) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #3 | Individual cylinder timing advance compensation amount (No. 3) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #4 | Individual cylinder timing advance compensation amount (No. 4) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #5 | Individual cylinder timing advance compensation amount (No. 5) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #6 | Individual cylinder timing advance compensation amount (No. 6) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - |
·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
Turbocharger Control 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Intercooler Water Pump Speed | The rotational speed of the electric water pump assembly | Min.: -25600 rpm, Max.: 25599 rpm | 2000 to 7000 rpm: During electric water pump assembly operation | - |
| Intercooler Water Pump | The drive request duty ratio of the electric water pump assembly | Min.: 0%, Max.: 399.99% | 40 to 85%: During electric water pump assembly operation | - |
Mass Air Flow Meter (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mass Air Flow Circuit | Status of the mass air flow meter sub-assembly circuit | Normal or Abnormal | Normal | - |
VVT Control (Ptrl Valve Control)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| VVT Advance Fail | VVT control failure status | ON or OFF | OFF: Idling | ON: There is an intake VVT timing advance malfunction. |
| Exhaust VVT Retarded Fail | Exhaust VVT control failure status | ON or OFF | OFF: Idling | ON: There is an exhaust VVT timing retarded malfunction. |
| Intake VVT Hold Learn Value Bank 1 | Intake VVT hold correct learned value for bank 1 | Min.: 0%, Max.: 399.9% | - | - |
| Intake VVT Hold Learn Value Bank 2 | Intake VVT hold correct learned value for bank 2 | Min.: 0%, Max.: 399.9% | - | - |
| Intake VVT Change Angle Bank 1 | Intake VVT displacement angle for bank 1 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | This is the intake VVT displacement angle. |
| Intake VVT Change Angle Bank 2 | Intake VVT displacement angle for bank 2 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | This is the intake VVT displacement angle. |
| Intake VVT OCV Control Duty Ratio Bank 1 | Intake cam timing oil control solenoid operation duty ratio for bank 1 | Min.: 0%, Max.: 399.9% | - | - |
| Intake VVT OCV Control Duty Ratio Bank 2 | Intake cam timing oil control solenoid operation duty ratio for bank 2 | Min.: 0%, Max.: 399.9% | - | - |
| Exhaust VVT Hold Learn Value Bank 1 | Exhaust VVT hold correct learned value for bank 1 | Min.: 0%, Max.: 399.9% | - | - |
| Exhaust VVT Hold Learn Value Bank 2 | Exhaust VVT hold correct learned value for bank 2 | Min.: 0%, Max.: 399.9% | - | - |
| Exhaust VVT Change Angle Bank 1 | Exhaust VVT displacement angle for bank 1 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | This is the exhaust VVT displacement angle. |
| Exhaust VVT Change Angle Bank 2 | Exhaust VVT displacement angle for bank 2 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | This is the exhaust VVT displacement angle. |
| Exhaust VVT OCV Control Duty Ratio Bank 1 | Exhaust cam timing oil control solenoid operation duty ratio for bank 1 | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | - |
| Exhaust VVT OCV Control Duty Ratio Bank 2 | Exhaust cam timing oil control solenoid operation duty ratio for bank 2 | Min.: 0%, Max.: 399.9% | 0 to 100%: Idling (engine warmed up) | - |
| Intake VVT Target Angle Bank 1 | Intake VVT target angle for bank 1 | Min.: 0 DegFR, Max.: 639.9 DegFR | 20 to 30 DegFR: Idling (engine warmed up) | - |
| Intake VVT Target Angle Bank 2 | Intake VVT target angle for bank 2 | Min.: 0 DegFR, Max.: 639.9 DegFR | 20 to 30 DegFR: Idling (engine warmed up) | - |
| Exhaust VVT Target Angle Bank 1 | Exhaust VVT target angle for bank 1 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | - |
| Exhaust VVT Target Angle Bank 2 | Exhaust VVT target angle for bank 2 | Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 10 DegFR: Idling (engine warmed up) | - |
| Intake VVT Timing Most Over-Retarded Learn Value Bank 1 | Intake VVT maximum retarded angle learned value for bank 1 | Min.: 0 deg(CA), Max.: 639.99 deg(CA) | 19.5 to 42.5 deg(CA): Idling (engine warmed up) | - |
| Intake VVT Timing Most Over-Retarded Learn Value Bank 2 | Intake VVT maximum retarded angle learned value for bank 2 | Min.: 0 deg(CA), Max.: 639.99 deg(CA) | 19.5 to 42.5 deg(CA): Idling (engine warmed up) | - |
| Exhaust VVT Timing Most Over-Advanced Learn Value Bank 1 | Exhaust VVT maximum advanced angle learned value for bank 1 | Min.: 0 deg(CA), Max.: 639.99 deg(CA) | 103 to 139 deg(CA): Idling (engine warmed up) | - |
| Exhaust VVT Timing Most Over-Advanced Learn Value Bank 2 | Exhaust VVT maximum advanced angle learned value for bank 2 | Min.: 0 deg(CA), Max.: 639.99 deg(CA) | 103 to 139 deg(CA): Idling (engine warmed up) | - |
Turbocharger Control 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Boost Pressure | The target boost pressure | Min.: 0 kPa [0 psi], Max.:2047.96 kPa [296.95 psi] | Atmospheric pressure to 300 kPa [43.5 psi] |
·
Check by comparing with the boost pressure sensor.
·
The boost pressure sensor remaining 20 kPa [2.9 psi] below the target boost pressure for 5 seconds or more when the accelerator pedal is fully depressed may lead to a sensation of lack of power.
·
When driving with the accelerator pedal fully depressed at an engine speed of 3000 rpm or higher, the boost pressure sensor approximately equals the target boost pressure.
·
The target boost pressure is the value calculated by the ECM. |
| Target Boost Pressure Supported | Status of the Target Boost Pressure Supported | Supp or Unsupp | Supp | - |
| Target Boost Pressure2 Supported | Status of the Target Boost Pressure2 Supported | Supp or Unsupp | Unsupp | - |
| Boost Pressure Sensor | Compressor outlet pressure value | Min.: 0 kPa [0 psi], Max.:2047.96 kPa [296.95 psi] | 90 to 100 kPa [13.5 to 14.5 psi] (Depends on atmospheric pressure): Idling |
·
At ignition switch ON or during idling, the boost pressure sensor approximately equals the atmospheric pressure (standard atmospheric pressure is 101 kPa [14.65 psi]).
·
When diagnosing a lack of power, check by comparing to the target boost pressure.
·
The boost pressure sensor remaining 20 kPa [2.9 psi] below the target boost pressure for 5 seconds or more when the accelerator pedal is fully depressed may lead to a sensation of lack of power.
·
The boost pressure sensor indicates the output value of the No. 2 turbo pressure sensor.
·
At ignition switch ON, the Turbocharger/Supercharger Inlet Pressure Bank1, Turbocharger/Supercharger Inlet Pressure Bank2 and Boost Pressure Sensor are approximately equal. |
| Boost Pressure Sensor Supported | Status of the Boost Pressure Sensor Supported | Supp or Unsupp | Supp | - |
| Boost Pressure Sensor2 Supported | Status of the Boost Pressure Sensor2 Supported | Supp or Unsupp | Unsupp | - |
Catalyst (Ptrl CAT Converter)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Catalyst Temperature B1S1 | Front catalyst temperature for bank 1 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - |
·
This is the temperature of the front catalyst estimated by the ECM.
·
This item is included in the conditions used to detect catalyst deterioration (DTC P042000), etc., and should therefore be used as a reference when recreating malfunction conditions. |
| Catalyst Temperature B2S1 | Front catalyst temperature for bank 2 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - |
·
This is the temperature of the front catalyst estimated by the ECM.
·
This item is included in the conditions used to detect catalyst deterioration (DTC P043000), etc., and should therefore be used as a reference when recreating malfunction conditions. |
| Catalyst Temperature B1S2 | Rear catalyst temperature for bank 1 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | This is the temperature of the rear catalyst estimated by the ECM. |
| Catalyst Temperature B2S2 | Rear catalyst temperature for bank 2 | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | This is the temperature of the rear catalyst estimated by the ECM. |
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter signal | ON or OFF |
·
ON: Starter operating
·
OFF: Starter not operating |
- |
| Neutral Position SW | Park/Neutral position switch status | ON or OFF | - | - |
| Shift SW Status (Neutral) Supported | Status of Shift SW Status (Neutral) supported | Unsupp or Supp | Unsupp | - |
| Stop Light SW | Stop light switch status | ON or OFF |
·
ON: Brake pedal depressed
·
OFF: Brake pedal released |
- |
| Immobiliser Communication | Immobiliser communication | ON or OFF | ON: Normal | - |
| Closed Throttle Position SW | Closed throttle position switch status | ON or OFF |
·
ON: Accelerator pedal fully released
·
OFF: Accelerator pedal depressed |
- |
Check Mode (Check Mode)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Misfire Test Result | Check mode result for misfire monitor | Compl or Incmpl | - | - |
| A/F (O2) Sensor B1S2 Test Results | Check mode result for air fuel ratio sensor (bank 1 sensor 2) | Compl or Incmpl | - | - |
| A/F (O2) Sensor B2S2 Test Results | Check mode result for air fuel ratio sensor (bank 2 sensor 2) | Compl or Incmpl | - | - |
| A/F (O2) Sensor B2S1 Test Results | Check mode result for air fuel ratio sensor (bank 2 sensor 1) | Compl or Incmpl | - | - |
| A/F (O2) Sensor B1S1 Test Results | Check mode result for air fuel ratio sensor (bank 1 sensor 1) | Compl or Incmpl | - | - |
Test Result (Monitor Status)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - |
·
* |
| Complete Parts Monitor Result | Comprehensive component monitor | Compl or Incmpl | - |
·
* |
| Ignition Monitor | Ignition monitor | Spark Ignition or Compression Ignition | Spark Ignition | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - |
·
* |
| Fuel System Monitor Result | Fuel system monitor | Compl or Incmpl | - |
·
* |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - |
·
* |
| Misfire Monitor Result | Misfire monitor | Compl or Incmpl | - |
·
* |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - |
·
* |
| EGR/VVT Monitor Result | EGR/VVT monitor | Compl or Incmpl | - |
·
* |
| A/F (O2) Sensor Heater Monitor | A/F (O2) sensor heater monitor | Not Avl or Avail | - |
·
* |
| A/F (O2) Sensor Heater Monitor Result | A/F (O2) sensor heater monitor | Compl or Incmpl | - |
·
* |
| A/F (O2) Sensor Monitor | A/F (O2) sensor monitor | Not Avl or Avail | - |
·
* |
| A/F (O2) Sensor Monitor Result | A/F (O2) sensor monitor | Compl or Incmpl | - |
·
* |
| Secondary Air Injection System Monitor | Secondary air injection system monitor | Not Avl or Avail | - |
·
* |
| Secondary Air Injection System Monitor Result | Secondary air injection system monitor | Compl or Incmpl | - |
·
* |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - |
·
* |
| EVAP Monitor Result | EVAP monitor | Compl or Incmpl | - |
·
* |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - |
·
* |
| Heated Catalyst Monitor Result | Heated catalyst monitor | Compl or Incmpl | - |
·
* |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - |
·
* |
| Catalyst Monitor Result | Catalyst monitor | Compl or Incmpl | - |
·
* |
*:
Avail: The monitor is available on this vehicle.
Not Avl: The monitor is not available on this vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or cable is disconnected from the negative (-) battery terminal.
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TC Terminal | TC terminal status | ON or OFF | - | Active Test item [Activate the TC Terminal] support data. |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven with MIL on | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | - | This is the distance driven since the MIL was illuminated. |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 min, Max.: 65535 min | Running time after MIL turned on | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 min, Max.: 65535 min | Time after DTCs cleared | This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted. |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | Distance driven after DTCs cleared | This is the distance driven since DTCs were cleared (or since the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0, Max.: 255 | - | This is the number of warmup cycles after the DTCs were cleared. |
| Distance Traveled from Last Battery Cable Disconnect | Distance driven after battery cable disconnected | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | Total distance vehicle driven after battery cable disconnected | - |
| IG OFF Elapsed Time | Time after ignition switch off | Min.: 0 min, Max.: 655350 min | Cumulative time after ignition switch off | - |
| Soak IC Current Timer Value | Initial soak timer start time | Min.: 0 sec, Max.: 614390.625 sec | - | - |
| OBD Requirements | OBD requirement | - | EOBD (Euro OBD) | - |
| Number of Emission DTC | Emissions-related DTCs | Min.: 0, Max.: 127 | - | This is the number of emissions-related DTCs stored. |
Misfire (Ptrl Misfire)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Trigger Count | Ignition counter | Min.: 0, Max.: 65535 | 0 to 600 |
·
This is the cumulative number of ignitions.
·
This counter is increased by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions.
·
The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by the value of this item.
·
The misfire rate for each cylinder = Misfire Count Cylinder #1 to #6 / Ignition Trigger Count
|
| Misfire Count Cylinder #1 | Misfire count of No. 1 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 1 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #2 | Misfire count of No. 2 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 2 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #3 | Misfire count of No. 3 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 3 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #4 | Misfire count of No. 4 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 4 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #5 | Misfire count of No. 5 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 5 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #6 | Misfire count of No. 6 cylinder | Min.: 0, Max.: 255 | 0 |
·
This is the misfire count for No. 6 cylinder.
·
This counter is increased by one for each misfire and is cleared every 200 revolutions.
·
Check this item to help determine the malfunctioning cylinder. |
| All Cylinders Misfire Count | Misfire count of all cylinders | Min.: 0, Max.: 255 | 0 |
·
This is the total misfire count for all cylinders.
·
This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions. |
| Misfire RPM | Engine speed for first misfire range | Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: 0 misfires |
·
This is the average engine speed recorded when misfiring occurs.
·
The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of Engine Speed and Calculate Load stored in the Freeze Frame Data. When reproducing malfunction conditions, use this value as a reference. |
| Misfire Load | Engine load for first misfire range | Min.: 0%., Max.: 510% | 0%: 0 misfires |
·
This is the average engine load recorded when misfiring occurs.
·
The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of Engine Speed and Calculate Load stored in the Freeze Frame Data. When reproducing malfunction conditions, use this value as a reference. |
| Misfire Margin | Misfire monitoring | Min.: -128%, Max.: 127% | 0 to 127%: Idling with warm engine |
·
This is the misfire detection margin.
·
Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100%
·
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. This item is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring.
·
A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring.
·
Example: When the engine is determined to be misfiring, Misfire Margin = -128 to 0%. |
| Catalyst OT Misfire Fuel Cut | Fuel cut to prevent catalyst from overheating during misfire | Not Avl or Avail | Avail |
·
When a high frequency of misfires is concentrated in a certain cylinder, this function stops fuel injection for that cylinder.
·
For vehicles which support this function, stop this fuel cut using the Active Test and confirm the misfire counts to determine the malfunctioning cylinder.
·
Avail: "Fuel cut to prevent catalyst from overheating during misfire" available
·
Not Avl: "Fuel cut to prevent catalyst from overheating during misfire" not available |
| Catalyst OT Misfire Fuel Cut History | History of fuel cut to prevent catalyst from overheating during misfire | ON or OFF | OFF | This can be used to tell whether there was a large amount of misfires occurred at a certain cylinder. |
| Catalyst OT Misfire Fuel Cut Cylinder #1 | Fuel cut operation of No. 1 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #2 | Fuel cut operation of No. 2 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #3 | Fuel cut operation of No. 3 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #4 | Fuel cut operation of No. 4 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #5 | Fuel cut operation of No. 5 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #6 | Fuel cut operation of No. 6 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed (Starter Off) | Engine speed when starter off | Min.: 0 rpm, Max.: 51199 rpm | - | This is the engine speed immediately after the engine is started. |
| Starter Count | Number of times starter turned on after ignition switch turned to ON | Min.: 0, Max.: 255 | - |
·
Indicates the number of times starter turned ON in the current driving cycle.
·
Number of times starter turned ON before engine started displayed in the 1 position.
·
Number of times starter turned ON after engine started displayed in the 10 position. Example: If "21" is displayed on the GTS, the starter was turned ON 1 time before engine start and turned ON 2 times after engine start. (The maximum value for each counter is 9 times before engine start and 11 times after engine start) |
| Run Distance of Previous Trip | Distance driven during previous trip | Min.: 0 km (0 mile), Max.: 655.35 km (407.23 mile) | - | - |
| Engine Starting Time | Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm) | Min.: 0 ms, Max.: 655350 ms | - |
·
This is the time elapsed from when the starter turns on until the engine speed reaches 400 rpm.
·
This value is cleared 5 seconds after the engine is started and 0 ms will be displayed. |
| Engine Start Hesitation | History of hesitation during engine start | ON or OFF | - | This item changes to ON when the engine speed does not reach 500 rpm during cranking. |
| Low Revolution for Engine Start | History of low engine speed after engine start | ON or OFF | - | This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine. |
| Fuel Cut Elapsed Time | Time elapsed after engine runs at high speed | Min.: 0 sec, Max.: 68746 sec | - | This item shows the time elapsed since fuel cut occurred due to the engine speed dropping from a high speed (more than the engine speed at which fuel cut occurs + 500 rpm). |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Previous Trip Intake Temp | Intake air temperature during previous trip | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Engine Oil Temperature | Estimated engine oil temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Ambient Temp for A/C | Ambient temperature for A/C | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Previous Trip Ambient Temp | Ambient temperature during previous trip | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Rough Idle (Ptrl Rough Idle)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Compression Leakage Count | Compression leakage count | Min.: 0, Max.: 255 | 0 | When the counter displays 5 or higher during an engine stall, startability malfunction or rough idle, it may be the result of pressure loss caused by deposits jamming the valve, etc. |
| Rough Idle Status | Rough idle status | Normal, Misfire, Continuous poor combustion, Intermittent poor combustion, Low frequency poor combustion | Normal | The following list of statuses indicates the degree and frequency of rough idling from highest to lowest. Use this as a reference when trying to reproduce the rough idling.
1.
Misfire
2.
Continuous poor combustion
3.
Intermittent poor combustion
4.
Low frequency poor combustion |
| Plural Cylinders Rough Idle | Status of multiple cylinders rough idle | ON or OFF | OFF | Indicates multiple cylinders are the cause of rough idling when ON. |
| Rough Idle Cylinder #1 | Status of the rough idle #1 | ON or OFF | OFF |
·
Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.
·
This item indicates cylinders which are likely to be the cause of rough idle. |
| Rough Idle Cylinder #2 | Status of the rough idle #2 | ON or OFF | OFF | Same as Rough Idle Cylinder #1. |
| Rough Idle Cylinder #3 | Status of the rough idle #3 | ON or OFF | OFF | Same as Rough Idle Cylinder #1. |
| Rough Idle Cylinder #4 | Status of the rough idle #4 | ON or OFF | OFF | Same as Rough Idle Cylinder #1. |
| Rough Idle Cylinder #5 | Status of the rough idle #5 | ON or OFF | OFF | Same as Rough Idle Cylinder #1. |
| Rough Idle Cylinder #6 | Status of the rough idle #6 | ON or OFF | OFF | Same as Rough Idle Cylinder #1. |
Various Vehicle Conditions 5 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine ECU Internal Temperature | ECM internal temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Total Distance Indicated after Long Term Leaving with IG OFF (1st) | Cumulative distance before 1st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Indicated after Long Term Leaving with IG OFF (2nd) | Cumulative distance before 2st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Indicated after Long Term Leaving with IG OFF (3rd) | Cumulative distance before 3st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 km, Max: 131070 km | - | - |
| Time of Long Term Leaving with IG OFF (1st) | Number of days of 1st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 day, Max.: 255 day | - | - |
| Time of Long Term Leaving with IG OFF (2nd) | Number of days of 2st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 day, Max.: 255 day | - | - |
| Time of Long Term Leaving with IG OFF (3rd) | Number of days of 3st long term ignition switch off period of time (1440 hours (60 days)) | Min.: 0 day, Max.: 255 day | - | - |
| IG ON Time Up to 1 trip before | Time ignition switch was ON 1 trip before | Min.: 0 min, Max.: 510 min | - | - |
| IG ON Time Up to 2 trip before | Time ignition switch was ON 2 trip before | Min.: 0 min, Max.: 510 min | - | - |
| IG ON Time Up to 3 trip before | Time ignition switch was ON 3 trip before | Min.: 0 min, Max.: 510 min | - | - |
| IG ON Time Up to 4 trip before | Time ignition switch was ON 4 trip before | Min.: 0 min, Max.: 510 min | - | - |
| IG ON Time Up to 5 trip before | Time ignition switch was ON 5 trip before | Min.: 0 min, Max.: 510 min | - | - |
| Auxiliary Battery Average Current during IG OFF 1 Trip before | Average battery current when ignition switch off 1 trip before | Min.: -32.768 A, Max: 32.767 A | - | - |
| Auxiliary Battery Average Current during IG OFF 2 Trip before | Average battery current when ignition switch off 2 trip before | Min.: -32.768 A, Max: 32.767 A | - | - |
| Auxiliary Battery Average Current during IG OFF 3 Trip before | Average battery current when ignition switch off 3 trip before | Min.: -32.768 A, Max: 32.767 A | - | - |
| Auxiliary Battery Average Current during IG OFF 4 Trip before | Average battery current when ignition switch off 4 trip before | Min.: -32.768 A, Max: 32.767 A | - | - |
| Auxiliary Battery Average Current during IG OFF 5 Trip before | Average battery current when ignition switch off 5 trip before | Min.: -32.768 A, Max: 32.767 A | - | - |
| Engine Run Time before 1 trip | Total time ignition switch was turned on during previous trip (1) | Min.: 0 min, Max.: 510 min | - | - |
| Engine Run Time before 2 trip | Total time ignition switch was turned on during previous trip (2) | Min.: 0 min, Max.: 510 min | - | - |
| Engine Run Time before 3 trip | Total time ignition switch was turned on during previous trip (3) | Min.: 0 min, Max.: 510 min | - | - |
| Engine Run Time before 4 trip | Total time ignition switch was turned on during previous trip (4) | Min.: 0 min, Max.: 510 min | - | - |
| Engine Run Time before 5 trip | Total time ignition switch was turned on during previous trip (5) | Min.: 0 min, Max.: 510 min | - | - |
| Total Distance Up to 1 Trip before | Cumulative distance traveled 1 trip before | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Up to 2 Trip before | Cumulative distance traveled 2 trip before | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Up to 3 Trip before | Cumulative distance traveled 3 trip before | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Up to 4 Trip before | Cumulative distance traveled 4 trip before | Min.: 0 km, Max: 131070 km | - | - |
| Total Distance Up to 5 Trip before | Cumulative distance traveled 5 trip before | Min.: 0 km, Max: 131070 km | - | - |
| Battery Current | Battery current | Min.: -125 A, Max.: 124.9 A | Changes according to alternator output (While driving after engine warmed up) | If the result is not as specified, a malfunction of the LIN communication line is suspected. |
| Battery Temperature | Battery temperature | Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | Changes according to actual temperature (While driving after engine warmed up) | If the result is not as specified, a malfunction of the LIN communication line is suspected. |
| Alternator Output Duty Ratio | Generator output duty ratio | Min.: 0%, Max.: 399.9% | - | - |
| Status of Alternator Temperature High | Alternator high temperature status | ON or OFF | - | - |
| Alternator Voltage - Non Active Test | Request voltage when regulator not under forced activation | Min.: 0 V, Max.: 79.998 V | Battery electrolyte temperature varies (12.7 to 15.3 V) while driving: After engine start | - |
| Voltage of Alternator | Alternator voltage | Min.: 0 V, Max.: 79.99 V | - | - |
| Auxiliary Battery Charging Integrated Current | Cumulative battery charging integrated current value since vehicle was built | Min.: 0 Ah, Max.: 429496729.5 Ah | - | - |
| Auxiliary Battery Discharging Integrated Current | Cumulative battery discharging integrated current value since vehicle was built | Min.: 0 Ah, Max.: 429496729.5 Ah | - | - |
| Auxiliary Battery Integrated Thermal Load | Cumulative battery thermal load since vehicle was built | Min.: 0, Max.: 4294967295 | - | - |
| Auxiliary Battery Capacity after IG ON | Battery level just after ignition switch turned to ON | Min.: -128 Ah, Max.: 127 Ah | - | - |
| Auxiliary Battery Capacity after IG OFF | Battery level just after ignition switch turned off | Min.: -128 Ah, Max.: 127 Ah | - | - |
| Integrated Engine Run Time | Cumulative time ignition switch has been ON since vehicle was built | Min.: 0 hour, Max.: 65535 hour | - | - |
| Number of Long Term Leaving with IG OFF | Number of times ignition switch not changed from off for long period of time (1440 hours (60 days)) | Min.: 0, Max.: 255 | - | - |
| Previous Trip Alternator Max Output Time | Accumulated time of maximum power generation by alternator during previous trip | Min.: 0 sec, Max.: 65535 sec | - | - |
| Initial Engine Battery Minimum Voltage | Minimum battery voltage at engine start | Min.: 0 V, Max.: 25.5 V | - | - |
| Previous Trip Charge Control Time | Previous trip charge control time | Min.: 0 sec, Max.: 65535 sec | - | - |
| Previous Trip Average Battery Temperature | Previous trip Average battery temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
| Battery Charging Rate Accuracy | Battery charging rate accuracy | Low/Middle/High/Disable | - | - |
| Auxiliary Battery Charging Rate Feedback Value | Collection value for SOC based on battery full charging | Max.: 6553.5% | - | - |
| Auxiliary Battery Charging Rate Controlling Value | SOC value recognized by charging control system | Max.: 6553.5% | - | Changes in accordance with the Data List "Auxiliary Battery Charging Rate Feedback Value". |
| Battery Status of Full Charge | Battery status of full charge | Min.: 0 Ah, Max.: 127.5 Ah | - | - |
| IG OFF Time before 1 trip | Number of days ignition switch was off 1 trip before | Min.: 0 day, Max.: 255 day | - | - |
| IG OFF Time before 2 trip | Number of days ignition switch was off 2 trip before | Min.: 0 day, Max.: 255 day | - | - |
| IG OFF Time before 3 trip | Number of days ignition switch was off 3 trip before | Min.: 0 day, Max.: 255 day | - | - |
| IG OFF Time before 4 trip | Number of days ignition switch was off 4 trip before | Min.: 0 day, Max.: 255 day | - | - |
| IG OFF Time before 5 trip | Number of days ignition switch was off 5 trip before | Min.: 0 day, Max.: 255 day | - | - |
| Electronic Control Coupling Fan Speed | Coupling fan speed | Min.: 0 rpm, Max.: 16383.75 rpm | - | - |
| Brake Override System | Brake override system status | ON or OFF | ON: Brake override system operating | - |
| Immobiliser Fuel Cut Status | Status of immobiliser fuel cut | ON or OFF | OFF | - |
| Immobiliser Fuel Cut History | Immobiliser fuel cut history | ON or OFF | OFF | - |
| Fuel Cut Condition | Fuel cut condition | ON or OFF | ON: Fuel cut operating | - |
| Idle Fuel Cut | Idle fuel cut condition | ON or OFF | ON: Fuel cut operating | - |
| TAU Fuel Cut | Low load fuel cut condition | ON or OFF | ON: Fuel cut operating | - |
| Electric Component Actuation Restriction Count | Electric component actuation restriction count | Min.: 0, Max.: 255 | - | - |
| Power Steering Pressure | Power steering oil pressure | Min.: 0 MPa, Max.: 25.599 MPa | - | - |
Compression (Compression)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed Cylinder #1 | Engine speed for No. 1 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 1 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #2 | Engine speed for No. 2 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 2 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #3 | Engine Speed Cylinder for No.3 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 3 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #4 | Engine speed for No. 4 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 4 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #5 | Engine speed for No. 5 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 5 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #6 | Engine speed for No. 6 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - |
·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)
·
This is the engine speed of No. 6 cylinder measured during fuel-cut with the engine cranking.
·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Average Engine Speed of All Cylinder | Average engine speed for all cylinders | Min.: 0 rpm, Max.: 51199 rpm | - | Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.) |
Various Vehicle Conditions 6 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Received MIL from ECT | MIL status from ECT | ON or OFF | - | - |
| Output Axis Speed | Output shaft speed | Min.: 0 rpm, Max.: 12750 rpm | - | - |
| NT Sensor Speed | Input turbine speed | Min.: 0 rpm, Max.: 12750 rpm | - | - |
| Shift SW Status (N,P Range) | Shift lever status (P or N position) | ON or OFF |
·
OFF: shift lever in N or P
·
ON: shift lever not in N or P |
- |
| Shift SW Status (N,P Range) Supported | Status of the Shift SW Status (N,P Range) Supported | Supp or Unsupp | Supp | - |
| Sport Shift Up SW | Sport shift up switch status | ON or OFF |
·
ON: "+" shift paddle operated (up shift)
·
OFF: "+" shift paddle not operated (up shift) |
- |
| Sport Shift Down SW | Sport shift down switch status | ON or OFF |
·
ON: "-" shift paddle operated (down shift)
·
OFF: "-" shift paddle not operated (down shift) |
- |
| Shift SW Status (S Range) | Transmission control switch status | ON or OFF |
·
ON: Shift lever in M
·
OFF: Shift lever not in M |
- |
| Snow Mode SW | 2nd switch status | ON or OFF | - | - |
| A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F), Max.: 150°C (302°F) |
·
Approximately 80°C (176°F): After stall speed test
·
Equal to ambient temperature: When engine is cold |
- |
| Drive Mode Status | Drive mode status | Normal, Power, Sport, Sport+, Comfort or ECO | - | - |
| Endless Rotary Switch (Phase A) | Mode select rotary switch status | ON or OFF | - | - |
| Endless Rotary Switch (Phase B) | Mode select rotary switch status | ON or OFF | - | - |
| Multi Terrain Select Mode Switching Switch | Multi terrain select mode switch status | ON or OFF | - | - |
| Drive Mode Select Switching Switch | Drive mode select switch status | ON or OFF | - | - |
| Lock Up Status | Lock up | ON or OFF |
·
ON: Lock-up operating
·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gear shift command | 1st, 2nd, 3rd, 4th, 5th, 6th, 7th, 8th, 9th or 10th | Same as actual gear | - |
| Off-road Guidance Status | Off road mode status | Normal, Grass & Snow, Mud & Sand, Loose Rock, Mogul or Rock & Dirt | - | - |
| Snow or 2nd Start Mode Status | 2nd start mode status | ON or OFF | - | - |
| Stop and Start System Engine Status | Stop and start system engine status | IG, Run, Stopreq, Stop, Restart | - | - |
| Battery Type | Battery Type | Specified or Other | - | - |
| Body Control with Torque Demand | Body Control with Torque Demand status | ON or OFF | Under the Body Control with Torque Demand: ON | - |
Turbocharger Control 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Bypass Valve Control | Operation status of the air by-pass valve assembly (bank 1). | ON or OFF | OFF (Close): Idling and waste gate valve active detection not operating | Does not operate during racing due to control based on engine load. |
| Air Bypass Valve Control Bank2 | Operation status of the air by-pass valve assembly (bank 2). | ON or OFF | OFF (Close): Idling and waste gate valve active detection not operating | Does not operate during racing due to control based on engine load. |
Low-speed Pre-ignition (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Consecutive Prevention Cylinder #1 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #1 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #1 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #1 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #2 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #2 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #2 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #2 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #3 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #3 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #3 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #3 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #4 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #4 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #4 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #4 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #5 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #5 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #5 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #5 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #6 History 1 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #6 History 2 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #6 History 3 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Consecutive Prevention Cylinder #6 History 4 | The distance traveled where low-speed pre-ignition occurred for each cylinder (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Fuel Cut History 1 | Fuel-cut history when low-speed pre-ignition occurred (Latest) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Fuel Cut History 2 | Fuel-cut history when low-speed pre-ignition occurred (Past 1) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Fuel Cut History 3 | Fuel-cut history when low-speed pre-ignition occurred (Past 2) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Fuel Cut History 4 | Fuel-cut history when low-speed pre-ignition occurred (Past 3) | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | - | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
| Distance for Control | Distance traveled after history initialization | Min.: 0 km (0 mile), Max.: 1310719 km (814481 mile) | Current distance traveled or distance traveled after history initialization. | If the history was initialized using the GTS "Heavy Knock History", this indicates the pre-ignition history at distances traveled after initialization. |
Grille Shutter (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Grille Shutter Position | Grille shutter position | Min.: 0%, Max.: 255% | 0%: Open | - |
| Grille Shutter Control Mode | Grille shutter control mode status | Normal or Maintenance |
·
Normal: Normal mode
·
Maintenance: Maintenance mode |
- |
| Grille Shutter Stuck Status | Grille shutter stuck status | OFF or ON | OFF | When the value is "ON", the swing grille actuator assembly is stuck. |
| Grille Shutter Slipping Status | Grille shutter slipping status | OFF or ON | OFF | When the value is "ON", the swing grille actuator assembly is free spinning. |
Specification Information (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Number of Specification Information Switching | Number of specification information switching | Min.: 0, Max.: 255 | - | - |
| Suspension Control Module Specification Information Switching | Whether or not the suspension system specification information switching is supported | Unsupp or Supp | Supp | - |
| Suspension Control Module Specification Information | Suspension system specification information | Existence, Nonexistence or Incomplete | Existence: AVS equipped Nonexistence: AVS not equipped Incomplete: Specification information is unlearned |
If Incomplete is displayed, perform Switch Specification Information using Utility. |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Injection Volume | Control the injection volume | Between -12.5% and 24.8% |
·
All fuel injector assemblies are tested at the same time.
·
Injection volume can be changed in fine gradations within the control range.
·
This Active Test enables the checking and graphing of the air fuel ratio sensor (sensor 1 and sensor 2) current outputs.
·
To perform this Active Test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B2S1, A/F (O2) Sensor Current B1S2 and A/F (O2) Sensor Current B2S2.
·
During the Active Test, air fuel ratio feedback control and feedback learning are stopped. |
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% |
·
All fuel injector assemblies are tested at the same time.
·
This Active Test enables the checking and graphing of the air fuel ratio sensor (sensor 1 and sensor 2) current outputs.
·
To perform this Active Test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B2S1, A/F (O2) Sensor Current B1S2 and A/F (O2) Sensor Current B2S2.
·
During the Active Test, air fuel ratio feedback control and feedback learning are stopped. |
| Activate the EVAP Purge VSV | Activate purge VSV control | ON/OFF | The purge VSV is opened with approximately 50% duty ratio. |
| Activate the Air Bypass Valve | Activate air by-pass valve assembly (bank 1) | ON/OFF | Perform this test when vehicle is stopped. |
| Activate the Air Bypass Valve Bank2 | Activate air by-pass valve assembly (bank 2) | ON/OFF | Perform this test when vehicle is stopped. |
| Activate the Circuit Relay (Brushless) | Activate fuel pump assembly (for low pressure side) | ON/OFF | Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Engine is stopped.
·
Shift lever in P. |
| Control the Fuel Pump Duty Ratio (Brushless) | Change the fuel pump speed (for low pressure side) | Low/High | Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Engine is stopped.
·
Shift lever in P. |
| Fuel Pump Single Phase Energization | Energizes a single phase of fuel pump control ECU | U Phase/V Phase/W Phase | Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Shift lever in P.
·
Connector from fuel pump control ECU to fuel pump assembly (for low pressure side) is disconnected. |
| Activate the TC Terminal | Turn on and off TC and TE1 (CG) connection | ON/OFF |
·
Confirm that the vehicle is stopped.
·
ON: TC and TE1 (CG) are connected.
·
OFF: TC and TE1 (CG) are disconnected. |
| Prohibit the Idle Fuel Cut | Prohibit idling fuel cut control | Start/Stop | Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Shift lever in P. |
| Prohibit the Catalyst OT Misfire Prevent Fuel Cut | Prohibit catalyst overheat protection fuel cut | Start/Stop Start: Fuel cut prohibited |
Perform this test when the engine speed is 3000 rpm or less. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator |
·
Close/Open
·
Start/Stop Open: Throttle valve opens slowly |
Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Engine is stopped.
·
Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more).
·
Shift lever in P. |
| Control the ETCS Open/Close Fast Speed | Throttle actuator |
·
Close/Open
·
Start/Stop Open: Throttle valve opens quickly |
·
Same as above.
·
See waveform *5. |
| Control the Intake VVT OCV Duty Ratio Bank 1 | Control cam timing oil control solenoid assembly (for intake camshaft of bank 1) | -100 to 100% (This value added to present cam timing oil control solenoid control duty) 100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the cam timing oil control solenoid assembly is set to 100%.
·
Perform this test when the following conditions are met:
-
Engine is running.
-
Shift lever in P.
·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Intake VVT OCV Duty Ratio Bank 2 | Control cam timing oil control solenoid assembly (for intake camshaft of bank 2) | -100 to 100% (This value added to present cam timing oil control solenoid control duty) 100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the cam timing oil control solenoid assembly is set to 100%.
·
Perform this test when the following conditions are met:
-
Engine is running.
-
Shift lever in P.
·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Exhaust VVT OCV Duty Ratio Bank 1 | Control cam timing oil control solenoid assembly (for exhaust camshaft of bank 1) | -100 to 100% (This value added to present cam timing oil control solenoid control duty) 100%: Maximum retard -100%: Maximum advance |
·
Engine stalls or idles roughly when the cam timing oil control solenoid assembly is set to 100%.
·
Perform this test when the following conditions are met:
-
Engine is running.
-
Shift lever in P.
·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Exhaust VVT OCV Duty Ratio Bank 2 | Control cam timing oil control solenoid assembly (for exhaust camshaft of bank 2) | -100 to 100% (This value added to present cam timing oil control solenoid control duty) 100%: Maximum retard -100%: Maximum advance |
·
Engine stalls or idles roughly when the cam timing oil control solenoid assembly is set to 100%.
·
Perform this test when the following conditions are met:
-
Engine is running.
-
Shift lever in P.
·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Target Fuel Pressure Offset | Control the target fuel pressure (for high pressure side) | -12.5 to 24.8% | Perform this test when the following conditions are met:
·
Engine is running.
·
Engine speed is 3000 rpm or less. |
| Control the Voltage of Alternator | Control the alternator | 12.5 to 14.7 V | Perform this test when vehicle is stopped. |
| Control the Injection Mode | Perform 2 pattern in order to operate fuel injection |
·
Port/Direct
·
Start/Stop |
Perform this test when the following conditions are met:
·
Vehicle stopped and engine idling.
·
Data List item "Injection Switching Status" is "OK". |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #6) injector fuel cut |
·
#1/#2/#3/#4/#5/#6
·
Start/Stop |
Perform this test when the following conditions are met:
·
Vehicle is stopped.
·
Engine is idling.
·
Shift lever in P. *1 |
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | Start/Stop | Perform this test when the following conditions are met:
·
Vehicle is stopped.
·
Engine is idling.
·
Shift lever in P. |
| Check the Cylinder Compression | Check the cylinder compression pressure | Start/Stop | Fuel injection and ignition stop of all cylinders. *2 |
| D-4S (Injection Volume) | Perform 2 pattern in order to operate injection volume |
·
Port/Direct
·
-12.5 to 24.8% |
Perform this test when the following conditions are met:
·
Vehicle is stopped.
·
Engine speed is 3000 rpm or less.
·
Data List item "Injection Switching Status" is "OK". |
| D-4S (A/F Control) | Perform 2 pattern in order to operate air fuel ratio control |
·
Port/Direct
·
-12.5% or 25% |
Perform this test when the following conditions are met:
·
Vehicle is stopped.
·
Engine speed is 3000 rpm or less.
·
Data List item "Injection Switching Status" is "OK". |
| D-4S (Fuel Cut) | Perform 2 pattern in order to operate fuel cut |
·
Port/Direct
·
#1/#2/#3/#4/#5/#6
·
Start/Stop |
Perform this test when the following conditions are met:
·
Vehicle is stopped.
·
Engine speed is 3000 rpm or less.
·
Data List item "Injection Switching Status" is "OK". |
| Control the Intercooler Water Pump | Control the electric water pump assembly | 0 to 100% | Perform this test when vehicle is stopped. |
| Control the Electronic Control Coupling Fan | Control the electric control coupling fan | 0 to 255% | Perform this test when engine coolant temperature is less than 100°C (212°F). |
| Control the Wastegate Valve Duty Ratio Bank1 | Control the waste gate valve (bank 1) | -30 to 30% | Perform this test when vehicle is stopped. |
| Control the Wastegate Valve Duty Ratio Bank2 | Control the waste gate valve (bank 2) | -30 to 30% | Perform this test when vehicle is stopped. |
| Control the Grille Shutter | Control the swing grille actuator assembly | 0% (open) to 100% (close) | Perform this test when the following conditions are met:
·
Ignition switch is ON.
·
Battery voltage is 10.5 to 16 V. |
If the display of the Data List item "Catalyst OT Misfire Fuel Cut" item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
If the display of the Data List item "Catalyst OT Misfire Fuel Cut" item is Avail, perform this Active Test as described below.
Clear the DTCs.
Turn the ignition switch to ON.
Enter the Control the Select Cylinder Fuel Cut.
Select the cylinder for fuel cut (No. 1 to No. 6 cylinder) and turn the Active Test ON.
Start the engine.
*2:
While performing this Active Test, the fuel injection and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.
To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded during the Active Test.
While the engine is not running, press the button to change Check the Cylinder Compression to "Start".
After performing the above procedure, the Active Test will start. Fuel injection for all cylinders is prohibited and engine speed measurement enters standby mode.
Crank the engine for about 10 seconds.
Continue to crank the engine until the values change from the default value (51199 rpm).
Monitor the engine speed (Engine Speed Cylinder #1 to #6) displayed on the GTS.
In order to protect the starter assembly, do not crank the engine continuously for 20 seconds or more.
If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to "Start" and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to "Start" and crank the engine.
Make sure the battery is fully charged before performing this Active Test.
At first, the GTS will display extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.
Stop cranking the engine, and then change "Check the Cylinder Compression" to "Stop" after the engine stops.
If the Active Test is changed to "Stop" while the engine is being cranked, the engine will start.
When performing the Active Test, Vehicle Control History code X0810 (Engine Difficult to Start (Engine Starting Time Long)) may be stored.
After performing the Active Test, make sure to check and clear DTCs.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.