If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.
| DTC Code | Component | Fail-Safe Operation | Fail-Safe Deactivation Condition |
|---|---|---|---|
| P001100 P001200 P002100 P002200 |
VVT system |
·
Intake VVT maximum retarded contact.
·
Boost prohibited.
·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001500 P002500 |
VVT system |
·
Exhaust VVT maximum advance contact.
·
Boost prohibited.
·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001600 P001800 |
VVT system |
·
Intake VVT maximum retarded contact.
·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001700 P001900 |
VVT system |
·
Exhaust VVT maximum advance contact.
·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P006D62 P00F762 |
·
No. 1 turbo pressure sensor
·
Atmospheric pressure sensor (ECM) |
Output power is limited. | Ignition switch off |
| P00CF62 P023511 P023515 |
No. 2 turbo pressure sensor | Boost prohibited. | Pass condition detected |
| P003012 P003013 P005012 P005013 P101A9E P103A9E |
Air fuel ratio sensor (sensor 1) heater | The ECM turns off the air fuel ratio sensor (sensor 1) heater. | Ignition switch off |
| P003312 P003314 P00C012 P00C014 |
Air by-pass valve assembly | Output power is limited. | Pass condition detected |
| P003612 P003613 P005612 P005613 P102A9E P105A9E |
Air fuel ratio sensor (sensor 2) heater | The ECM turns off the air fuel ratio sensor (sensor 2) heater. | Ignition switch off |
| P007A11 P007A15 |
Intake air temperature sensor (No. 3 turbo pressure sensor) |
·
The ECM estimates the intake air temperature to be 45°C (113°F).
·
Output power is limited. |
Pass condition detected |
| P008700 P008800 P123513 |
Fuel pump assembly (for high pressure side) |
·
Output power is limited.
·
Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi) |
Ignition switch off |
| P00AA11 P00AA15 P011011 P011015 |
Intake air temperature sensor (mass air flow meter sub-assembly) |
·
Boost prohibited.
·
The ECM estimates the intake air temperature to be 20°C (68°F). |
Pass condition detected and then ignition switch turned off |
| P010012 P010014 P010A12 P010A14 |
Mass air flow meter sub-assembly | Boost prohibited. | Pass condition detected and then ignition switch turned off |
| P011511 P011515 |
Engine coolant temperature sensor | The ECM estimates the engine coolant temperature to be 80°C (176°F). | Pass condition detected |
| P012011 P012015 P01201C P022011 P022015 P060444 P060647 P060747 P060787 P060D49 P060E49 P065714 P06579E P16B09F P210018 P210019 P211172 P211173 P211900 P211904 P211977 P21199B P21352B |
Electronic throttle control system |
·
Boost prohibited.
·
The ECM cuts off throttle actuator current for both bank 1 and bank 2, and the throttle valve is returned to a 8.5° throttle position by the return spring.
·
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to be driven at a low speed*1. |
Pass condition detected and then ignition switch turned off |
| P019011 P019015 |
Fuel pressure sensor (for high pressure) |
·
Output power is limited.
·
Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi) |
Ignition switch off |
| P020113 P020213 P020313 P020413 P020513 P020613 P062D13 |
ECM (injector driver) | Fuel cut is performed and then the output is limited when the engine speed is 1000 rpm or more. | Pass condition detected and then ignition switch turned off |
| P02351C | Turbocharger system | Boost prohibited. | Ignition switch off |
| P024300 P024318 P024319 P024700 P024718 P024719 P25B372 P25B473 P25B572 P25B673 P2AB711 P2AB715 P2ABA11 P2ABA15 |
Waste gate valve actuator assembly | Boost prohibited. | Pass condition detected and then ignition switch turned off |
| P026A00 | Intercooler system | Output power is limited. | Pass condition detected |
| P030000 P030027 P030085 P030100 P030200 P030300 P030400 P030500 P030600 *2 |
·
Port fuel injector assembly
·
Direct fuel injector assembly
·
Electronic throttle control system |
When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.
Under a low load and at a low engine speed: - Fuel cut is performed on the malfunctioning cylinder.
2.
Under a high load and at a high engine speed: - Throttle valve opening angle control is performed. - Fuel cut is performed on all cylinders or the malfunctioning cylinder. |
Pass condition detected and then ignition switch turned off |
| P032511 P032515 P033011 P033015 |
Knock control sensor | The ECM sets the ignition timing to maximum retard. | Ignition switch off |
| P048012 P048014 P04807F P052631 |
Electronic coupling fan control system |
·
Air conditioner off.
·
Electric control coupling fan is at maximum drive. |
Pass condition detected |
| P05042B | Stop light switch assembly | The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. | Ignition switch off |
| P056014 | ECM +B circuit | Generator command is maintained. | Pass condition detected and then ignition switch turned off |
| P059A71 P059A79 P05A212 P15AD87 |
Swing grille actuator assembly | The grille shutter system control is suspended. | Normal system condition detected, ignition switch turned off then to ON and normal grille shutter closing and opening operation performed |
| P107A11 P107A15 |
No. 2 fuel pressure sensor (for low pressure side) | Fuel pump assembly (for low pressure side) control is maintained. | Ignition switch off |
| P137800 | Pre-ignition | Output is limited in low-speed boost region. | Clear DTC after recovering to normal condition |
| P212012 P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
Accelerator pedal sensor assembly | The accelerator pedal position sensor has 2 sensor circuits: Main and Sub. If either circuit malfunctions, the ECM limits the engine output. If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. |
Pass condition detected and then ignition switch turned off |
| P21CF13 P21D013 P21D113 P21D213 P21D313 P21D413 |
Port fuel injector assembly | The ECM performs fuel-cut when the engine speed is 2000 rpm or more. | Pass condition detected and then ignition switch turned off |
| P222611 P222615 |
Atmospheric pressure sensor (ECM) | Boost prohibited. | Ignition switch off |
| P223711 P223712 P223713 P223716 P223717 P22371B P224011 P224012 P224013 P224016 P224017 P22401B P225111 P225112 P225411 P225412 |
Air fuel ratio sensor (sensor 1) | Air fuel ratio sensor (sensor 1) air fuel ratio feedback control is stopped. | Pass condition detected and then ignition switch turned off |
| P22AB11 P22AB12 P22AB13 P22AB16 P22AB17 P22B211 P22B212 P22B811 P22B812 P22B813 P22B816 P22B817 P22BF11 P22BF12 |
Air fuel ratio sensor (sensor 2) |
·
Control based on air fuel ratio sensor (sensor 2) air fuel ratio feedback is stopped.
·
The ECM turns off the air fuel ratio sensor (sensor 2) heater. |
Pass condition detected and then ignition switch turned off |
| P23AA72 P2C2972 |
Air by-pass valve assembly | Output power is limited. | Pass condition detected and then ignition switch turned off |
*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.