Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469670 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E384449E10
5.469,0.896 5.677,1.073 0.208,0.177 10 false IG 5.271,0.802 5.427,0.969 0.156,0.167 10 false 1 5.479,1.229 5.646,1.396 0.167,0.167 10 false E 5.219,1.615 5.604,1.792 0.385,0.177 10 false I58 2.635,0.49 3.615,0.76 0.979,0.271 10 false ECU-IGR NO.2 0.542,0.302 1.927,0.646 1.385,0.344 10 false from IGR NO.2 Relay 5.198,1.792 6.729,2.156 1.531,0.365 10 false Clearance Warning ECU Assembly 5.24,1.094 5.479,1.271 0.24,0.177 10 false 31 0.469,0.917 1.813,1.323 1.344,0.406 10 false from Engine Stop and start ECU 3.698,0.125 3.958,0.323 0.26,0.198 10 false *1 3.667,0.823 3.927,1.021 0.26,0.198 10 false *2 0.125,2.146 2.375,2.438 2.25,0.292 10 false *1: w/o Stop and Start System 0.115,2.469 2.365,2.76 2.25,0.292 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY POWER SOURCE)
a.

Disconnect the I58 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Click Location & Routing(I58)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

I58-1 (IG) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
I58-1 (IG) - Body ground Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the I58 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

I58-31 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR