Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469674 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E334124E44
0.865,5.302 2.99,5.51 2.125,0.208 10 false : CAN Communication Line 6.115,1.135 6.625,1.333 0.51,0.198 10 false to CAN 3.344,2.167 4.531,2.75 1.188,0.583 10 false Blind Spot Monitor Sensor LH (B) 3.469,4.75 4.646,5.292 1.177,0.542 10 false Blind Spot Monitor Sensor RH (A) 0.208,0.708 1.146,1.26 0.938,0.552 10 false from IGR-NO.2 Relay 3.594,0.708 4.188,0.99 0.594,0.281 10 false BLB 3.594,1.51 4.188,1.792 0.594,0.281 10 false BLGD 3.427,0.594 4.021,0.875 0.594,0.281 10 false 5 3.365,1.417 3.958,1.698 0.594,0.281 10 false 10 3.333,2 3.927,2.281 0.594,0.281 10 false T10 3.458,4.573 4.052,4.854 0.594,0.281 10 false Q21 3.604,3.292 4.198,3.573 0.594,0.281 10 false BRB 3.615,4.104 4.208,4.385 0.594,0.281 10 false BRGD 3.438,3.135 4.031,3.417 0.594,0.281 10 false 5 3.375,3.99 3.969,4.271 0.594,0.281 10 false 10 1.667,0.885 3.063,1.219 1.396,0.333 10 false ECU-IGR NO.2 6.094,1.313 7.073,2 0.979,0.688 10 false Communication System

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH [B] POWER SOURCE)
a.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
T10-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH [B] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH [B] - BODY GROUND)
a.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] POWER SOURCE)
a.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
Q21-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - BODY GROUND)
a.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR