Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0467925 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14B387  Lost Communication with Rear Panel LIN Missing Message  


DESCRIPTION

The cooler control switch assembly communicates with the air conditioning amplifier assembly via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B14B387 Lost Communication with Rear Panel LIN Missing Message Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Error or open in communication line between air conditioning amplifier assembly and cooler control switch assembly


Detection Time:

Continuously for 10 seconds or more


·

Harness or connector

·

Cooler control switch assembly

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Malfunction Status Error in communication line between air conditioning amplifier assembly and cooler control switch assembly ○ -
Open in communication line between air conditioning amplifier assembly and cooler control switch assembly - ○
Detection Time Continuously for 10 seconds or more Continuously for 10 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.


WIRING DIAGRAM

E459610E01
3.563,1.719 3.906,1.917 0.344,0.198 10 false IG 4.281,2.125 4.719,2.323 0.438,0.198 10 false RLIN 3.552,2.552 4.031,2.76 0.479,0.208 10 false E 3.281,1.583 3.594,1.781 0.313,0.198 10 false 10 4.677,1.958 4.99,2.156 0.313,0.198 10 false 5 3.333,2.427 3.646,2.625 0.313,0.198 10 false 6 3.021,3.01 3.458,3.208 0.438,0.198 10 false Q52 3.021,3.177 5.073,3.375 2.052,0.198 10 false Cooler Control Switch Assembly 5.146,0.26 5.583,0.458 0.438,0.198 10 false I31 5.302,3.083 6.885,3.469 1.583,0.385 10 false Air Conditioning Amplifier Assembly 5.531,2.135 5.969,2.333 0.438,0.198 10 false RLIN 5.167,1.875 5.438,2.063 0.271,0.188 10 false 20 0.677,3.396 2.333,3.604 1.656,0.208 10 false : LIN Communication Line 5.521,1.354 5.979,1.552 0.458,0.198 10 false GND2 5.198,1.094 5.469,1.281 0.271,0.188 10 false 4 5.188,0.031 5.458,0.219 0.271,0.188 10 false 1 5.208,0.51 5.479,0.698 0.271,0.188 10 false 6 5.521,0.313 5.979,0.51 0.458,0.198 10 false +B2 5.531,0.729 5.99,0.927 0.458,0.198 10 false IG+ 3.771,0.885 4.906,1.115 1.135,0.229 10 false A/C NO.1 2.229,0.25 3.635,0.479 1.406,0.229 10 false from Battery 2.313,1.865 3.448,2.094 1.135,0.229 10 false ECU-IGR NO.2 0.438,1.708 1.844,1.938 1.406,0.229 10 false from IGR-NO.2 Relay 5.156,0.729 5.594,0.927 0.438,0.198 10 false I33 5.135,1.344 5.573,1.542 0.438,0.198 10 false I31 5.177,2.115 5.615,2.313 0.438,0.198 10 false I31 3,1.583 3.313,1.781 0.313,0.198 10 false *1 3.031,2.156 3.344,2.354 0.313,0.198 10 false *2 1.688,0.719 3.094,0.948 1.406,0.229 10 false from IGP NO. 2 Relay 0.427,2.031 1.792,2.385 1.365,0.354 10 false from Engine Stop and Start ECU 0.552,2.802 2.604,3.042 2.052,0.24 10 false *1: w/ Stop and Start System 0.542,3.104 2.594,3.344 2.052,0.24 10 false *2: w/o Stop and Start System 3.656,0.417 4.792,0.646 1.135,0.229 10 false ECU-B NO.3

CAUTION / NOTICE / HINT

NOTICE:

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE CONDITION
Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q52)Location & Routing

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Q52-10 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q52)Location & Routing

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Q52-6 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the I31 air conditioning amplifier assembly connector.


b.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I31,Q52)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

I31-20 (RLIN) - Q52-5 (RLIN) Always Below 1 Ω
I31-20 (RLIN) or Q52-5 (RLIN) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT)
a.

Using an oscilloscope, check the waveform.

E459619C02
2.208,0.188 2.708,0.438 0.5,0.25 2.823,1.177 2.969,1.792 2.969,1.792 3.219,1.792 true 2.385,0.229 2.844,0.427 0.458,0.198 10 false I31 3.292,1.708 3.75,1.906 0.458,0.198 10 false RLIN 2.271,3.313 2.729,3.51 0.458,0.198 10 false GND 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)
- -


Tester Connection Tool Setting Switch Condition

Click Location & Routing(I31)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

I31-20 (RLIN) - Body ground 2 V/DIV., 20 ms/DIV. Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q52)Location & Routing

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Q52-10 (IG) - Body ground Ignition switch ON 10.5 to 16 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

7.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q52)Location & Routing

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Q52-6 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the I31 air conditioning amplifier assembly connector.


b.

Disconnect the Q52 cooler control switch assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I31,Q52)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

I31-20 (RLIN) - Q52-5 (RLIN) Always Below 1 Ω
I31-20 (RLIN) or Q52-5 (RLIN) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT)
a.

Using an oscilloscope, check the waveform.

E459619C02
2.208,0.188 2.708,0.438 0.5,0.25 2.823,1.177 2.969,1.792 2.969,1.792 3.219,1.792 true 2.385,0.229 2.844,0.427 0.458,0.198 10 false I31 3.292,1.708 3.75,1.906 0.458,0.198 10 false RLIN 2.271,3.313 2.729,3.51 0.458,0.198 10 false GND 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)
- -


Tester Connection Tool Setting Switch Condition

Click Location & Routing(I31)Location & Routing

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

I31-20 (RLIN) - Body ground 2 V/DIV., 20 ms/DIV. Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG