Home › Engine / Hybrid System › V35A-FTS (STARTING) › STARTER (w/ Stop And Start System)
RM38G0E _51 Engine / Hybrid System _101526 V35A-FTS STARTING _0470473 STARTER(w/ Stop And Start System) G

V35A-FTS STARTING  STARTER(w/ Stop And Start System)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

When replacing the starter assembly, it is necessary to replace the ST NO. 1 relay and ST NO. 2 relay as well.


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:
·

Do not use a thin cable to perform the inspection.

·

If a thin cable is used, the large electric current passing through the cable could cause it to overheat and catch fire, possibly resulting in injuries.



NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a no-load performance test.

i.
A489719C01
2.073,1.573 2.26,1.427 2.26,1.427 2.396,1.427 true 0.729,3.125 0.729,2.708 true 2.406,1.333 2.719,1.49 0.313,0.156 10 false *a 0.635,3.156 1.094,3.354 0.458,0.198 10 false SL1
*a Starter Body
V100135

Moves Outward


Connect the positive (+) lead to terminal SL1.


ii.

Connect the negative (-) lead to the starter body and check that the clutch pinion gear moves outward.

NOTICE:

If the positive (+) and negative (-) leads are connected incorrectly, the IC inside of the starter inrush current reduction relay will be damaged. Be sure to connect them correctly.


If the result is not as specified, replace the starter assembly.


iii.
A489720C01
2.063,1.573 2.281,1.375 2.281,1.375 2.438,1.375 true 0.729,3.042 0.729,2.698 true 2.49,1.281 2.802,1.438 0.313,0.156 10 false *a 0.656,3.063 1.115,3.229 0.458,0.167 10 false SL1
*a Starter Body
V100136

Moves Inward


With the clutch pinion gear in the outward position, disconnect the negative (-) lead and check that the clutch pinion gear returns inward.

If the result is not as specified, replace the starter assembly.


iv.
A489721C01
2.083,1.281 2.323,1.052 2.323,1.052 2.521,1.052 true 0.948,3.073 0.948,2.698 true 2.552,0.969 2.865,1.125 0.313,0.156 10 false *a 0.854,3.094 1.313,3.292 0.458,0.198 10 false SL2
*a Starter Body


Connect the positive (+) lead to terminal SL2 of the connector and the negative (-) lead to the starter body. Check that a clicking sound is heard from the magnet switch.

If the result is not as specified, replace the starter assembly.


v.

Hold the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



vi.

Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.

A489722C01
3.729,1.135 3.823,0.948 3.823,0.948 3.948,0.948 true 1.74,1.948 1.938,1.948 1.938,1.948 2.208,1.438 true 3.438,2.208 3.438,2.521 true 3.99,0.875 4.302,1.031 0.313,0.156 10 false *a 1.563,1.875 1.875,2.031 0.313,0.156 10 false *b 0.927,0.667 1.24,0.823 0.313,0.156 10 false *c 3.344,2.552 3.688,2.719 0.344,0.167 10 false SL2
*a Starter Body *b Terminal 30
*c AC/DC 400 A Probe - -



vii.

Connect terminal SL2 and measure the current after the ammeter (AC/DC 400A probe) reading has stabilized.

Standard current:

130 A or less at 11.5 V


If the starter assembly does not operate when terminal SL2 is connected, replace the starter assembly.



Hide 28226B 2.INSPECT REPAIR SERVICE STARTER KIT

a.
A385437

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

NOTICE:
·

To avoid damaging the inside of the magnet switch, do not release the plunger quickly.

·

Do not drop the plunger.



If the plunger does not operate as specified, replace the repair service starter kit.



b.
A531434C01
1.844,1.438 2.052,1.031 2.052,1.031 2.229,1.031 false 0.667,0.813 1.24,0.469 1.24,0.469 1.417,0.469 true 0.604,0.635 1.177,0.229 1.177,0.229 1.365,0.229 true 1.469,0.385 2.083,0.583 0.615,0.198 10 false SL1 1.396,0.135 2.01,0.333 0.615,0.198 10 false SL2 2.281,0.958 2.594,1.156 0.313,0.198 10 false *a
*a Repair Service Starter Kit Body


Check the repair service starter kit resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal SL1 - Repair service starter kit body Always Below 1 Ω
Terminal SL2 - Repair service starter kit body Below 2 Ω


If the result is not as specified, replace the repair service starter kit.



Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the resistance.

i.
A372882N01
0.5,0.74 1.271,0.948 true 0.573,2.031 1.125,1.677 false 1.417,2.76 1.781,2.49 false 2.292,3.604 2.698,3.604 false 1.76,4.198 1.115,3.698 false 0.365,0.677 0.521,0.875 0.156,0.198 10 false A 0.417,2.031 0.573,2.229 0.156,0.198 10 false B 1.854,2.406 2.01,2.604 0.156,0.198 10 false C 2.792,3.552 2.948,3.75 0.156,0.198 10 false D 1.844,4.177 2,4.375 0.156,0.198 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
C - D
D - E
Always Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



b.
A372727C02
2.385,1.135 2.698,1.333 0.313,0.198 10 false *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard Length (convex part):

14.4 mm (0.567 in.)


Minimum Length (convex part):

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



Hide 28160 4.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator appearance.

If the surface is dirty or burnt, replace the starter armature assembly.


b.
A224239C02
2.292,1.021 2.885,1.021 true 2.906,0.917 3.219,1.115 0.313,0.198 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A224240C02
0.875,1.333 1.354,0.917 true 2.396,0.979 2.75,0.51 true 2.698,0.354 3.01,0.552 0.313,0.198 10 false *a 0.719,1.323 1.031,1.521 0.313,0.198 10 false *b
*a Segment
*b Starter Armature Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A145291C09
1.927,1.573 0.469,1.844 0.469,1.844 0.604,0.906 true 0.25,1.75 0.563,1.906 0.313,0.156 10 false *a
*1 Armature Shaft


Check the commutator for runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the runout.

Maximum Runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the starter armature assembly.



e.
A062221

Using a vernier caliper, measure the commutator diameter.

Standard Diameter (convex part):

29 mm (1.14 in.)


Minimum Diameter (convex part):

28 mm (1.10 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A062222

Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard Undercut Depth (convex part):

0.7 mm (0.0276 in.)


Minimum Undercut Depth (convex part):

0.4 mm (0.0157 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28226C 5.INSPECT NO. 2 REPAIR SERVICE STARTER KIT

a.
A356505C01
0,0 0,0 false
V100135

Free
V100136

Lock


Check the clutch pinion gear teeth for wear or damage.

i.

Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the clutch pinion gear does not operate as specified, replace the No. 2 repair service starter kit.