Home › Engine / Hybrid System › V35A-FTS (EMISSION CONTROL) › PURGE VALVE
RM38G0E _51 Engine / Hybrid System _101527 V35A-FTS EMISSION CONTROL _0470482 PURGE VALVE G

V35A-FTS EMISSION CONTROL  PURGE VALVE  INSPECTION  


PROCEDURE

Hide 17650G 1.INSPECT PURGE VSV (DUTY VACUUM SWITCHING VALVE)

a.
A418599C02
1.552,0.177 1.917,0.417 0.365,0.24 0.063,0.042 0.271,0.271 0.208,0.229 10 false *a 1.604,0.198 1.927,0.396 0.323,0.198 10 false C44
*a Component without harness connected
(Purge VSV (Duty Vacuum Switching Valve))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C44)Location & Routing

Click Connector(C44)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Vacuum Switching Valve Assembly (Purge)

C44-1 - C44-2 20°C (68°F) 23 to 26 Ω
C44-1 - Body ground Always 10 MΩ or higher
C44-1 - Body ground Always 10 MΩ or higher


HINT:

When measuring the coil resistance make sure that the surface temperature of the purge VSV (duty vacuum switching valve) is 20°C (68°F).


If the result is not as specified, replace the purge VSV (duty vacuum switching valve).


b.
A477986C01
1.833,0.167 1.667,0.167 1.667,0.167 1.583,0.5 true 0.417,0.5 0.583,0.5 0.583,0.5 0.75,0.75 true 0.667,1.417 0.833,1.417 0.833,1.417 1,1.167 true 1.917,0.083 2.167,0.25 0.25,0.167 10 false *a 0.167,0.417 0.417,0.583 0.25,0.167 10 false *c 2.417,0.25 2.667,0.417 0.25,0.167 10 false *d 0.417,1.333 0.667,1.5 0.25,0.167 10 false *b
*a Port E
*b Port F
*c Port G
*d Air


Apply auxiliary battery voltage between the terminals of the purge VSV (duty vacuum switching valve) and check that the following occurs when blowing air into the port E.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(C44)Location & Routing

Click Connector(C44)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Vacuum Switching Valve Assembly (Purge)

C44-1 - C44-2 Battery voltage applied between the terminals Air flows from port F and port G
Battery voltage not applied between the terminals Air does not flow


If the result is not as specified, replace the purge VSV (duty vacuum switching valve).


c.

Install a clean hose to the purge VSV (duty vacuum switching valve).


d.

Check the operation of the duty vacuum switching valve.

CAUTION:

Do not suck air through the purge VSV (duty vacuum switching valve).

Petroleum substances inside the purge VSV (duty vacuum switching valve) are hazardous to your health.


i.
A477987C01
1.583,0.333 1.75,0.333 1.75,0.333 2.26,0.677 true 1.333,0.25 1.583,0.417 0.25,0.167 10 false *a 2.75,0.25 3,0.417 0.25,0.167 10 false *b
*a Clean Hose
*b Air


Blow air into the port E and check that air passes through easily.

If the result is not as specified, replace the purge VSV (duty vacuum switching valve).


ii.
A477989C01
1.031,1.427 1.198,1.427 1.198,1.427 1.49,1.177 true 0.813,1.333 1.063,1.5 0.25,0.167 10 false *a 2.042,1.885 2.292,2.052 0.25,0.167 10 false *b
*a Clean Hose
*b Air


Blow air into the port F and check that air passes through with difficulty.

If the result is not as specified, replace the purge VSV (duty vacuum switching valve).


iii.
A477988C01
0.833,0.667 1,0.667 1,0.667 1.167,1 true 0.583,0.583 0.833,0.75 0.25,0.167 10 false *a 0.167,1.167 0.417,1.333 0.25,0.167 10 false *b
*a Clean Hose
*b Air


Blow air into the port G and check that air passes through with difficulty.

If the result is not as specified, replace the purge VSV (duty vacuum switching valve).