Home › Engine / Hybrid System › 1GR-FE (COOLING) › RADIATOR
RM38G0E _51 Engine / Hybrid System _101532 1GR-FE COOLING _0470524 RADIATOR G

1GR-FE COOLING  RADIATOR  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343701

Do not remove the reserve tank cap, radiator cap sub-assembly, radiator drain cock plug or cylinder block water drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 16401 1.INSPECT RADIATOR CAP SUB-ASSEMBLY

CAUTION:

Do not remove the reserve tank cap, radiator cap sub-assembly, radiator drain cock plug or cylinder block water drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.

Measure the valve opening pressure.

i.
A301464N01
0.427,1.375 0.583,1.573 0.156,0.198 10 false 1 0.677,1.573 0.833,1.771 0.156,0.198 10 false 2 0.948,1.885 1.104,2.083 0.156,0.198 10 false 3 2.656,1.583 2.813,1.781 0.156,0.198 10 false 4

If there are water stains or foreign matter on rubber packing 1, 2 or 3, clean it by using water and finger scouring.


ii.

Check that rubber packing 1, 2 and 3 are not deformed, cracked or swollen.


iii.

Check that rubber packing 3 and 4 are not stuck together.


iv.

Apply engine coolant to rubber packing 2 and 3.


v.
A301465C03
1.885,1 2.042,0.396 2.042,0.396 2.24,0.396 false 0.458,1.552 0.458,1.021 false 0.385,1.594 0.698,1.75 0.313,0.156 10 false *1 2.281,0.313 2.479,0.51 0.198,0.198 10 false *a 1.594,1.427 1.792,1.625 0.198,0.198 10 false *b
*1 Radiator Cap Sub-assembly
*a Radiator Cap Tester
*b 30° or more


When using the radiator cap tester, tilt it 30° or more.


vi.

Pump the radiator cap tester several times and check the maximum pressure.*1

Pumping speed:

1 pump per second


HINT:

*1: Even if the cap cannot maintain the maximum pressure, it is not necessarily defective.


Standard Judgment Criterion:
Item Specified Condition
Standard Value
(for Brand-new Cap)
94 to 122 kPa (1.0 to 1.2 kgf/cm2, 14 to 18 psi)
Minimum Standard Value
(for Used Cap)
79 kPa (0.8 kgf/cm2, 11.5 psi)


If the maximum pressure is less than the minimum standard value, replace the radiator cap sub-assembly.



Hide 16400 2.INSPECT FINS FOR BLOCKAGE

a.

If the fins are clogged, wash them with water or a steam cleaner and dry them with compressed air.

NOTICE:
·

To avoid damaging the fins, the injection direction should be at right angles to the core surface.

·

If the steam cleaner is too close to the core, there is a possibility of damaging the fins, so keep the following injection distances.

Standard Injection Distance:
Injection Pressure Specified Condition
2942 to 4903 kPa
(30.0 to 50.0 kgf/cm2, 427 to 711 psi)
300 mm (11.8 in.)
4903 to 7845 kPa
(50.0 to 80.0 kgf/cm2, 711 to 1138 psi)
500 mm (19.7 in.)


·

If the fins are bent, straighten them with a screwdriver or pliers.

·

Do not expose electronic components to water.




b.

Dry the fins with compressed air.