Home › Engine / Hybrid System › 1GR-FE (STARTING) › STARTER
RM38G0E _51 Engine / Hybrid System _101534 1GR-FE STARTING _0470526 STARTER G

1GR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A341241C01
1.396,0.708 1.167,0.167 1.167,0.167 1,0.167 true 1.031,1.615 1.031,1.948 1.031,1.948 1.198,1.948 false 0.833,0.073 1.146,0.271 0.313,0.198 10 false *a 1.229,1.885 1.542,2.083 0.313,0.198 10 false *b
*a Terminal 50
*b Terminal C
V100135

Moves Outward


Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.
A341242C01
1.198,1.448 1.354,1.646 0.156,0.198 10 false .
V100135

Disconnect


Perform a holding test.

i.

Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.
A341243C01
2.198,1.104 2.354,1.302 0.156,0.198 10 false .
V100135

Disconnect
V100136

Returns Inward


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.
A341244C01
1.042,0.677 0.792,0.344 0.792,0.344 0.625,0.344 true 1.417,0.75 1.25,0.167 1.25,0.167 1.083,0.167 true 0.438,0.24 0.75,0.438 0.313,0.198 10 false *a 0.927,0.073 1.24,0.271 0.313,0.198 10 false *b
*a Terminal 30
*b Terminal 50


Connect the battery and an ammeter to the starter as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.

HINT:

Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.




Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A341246C01
1.01,1.063 0.844,0.729 0.844,0.729 0.677,0.729 false 2.344,1.615 2.583,1.75 2.583,1.75 2.75,1.75 false 1.708,0.781 2.208,0.167 2.208,0.167 2.375,0.167 false 0.5,0.635 0.813,0.833 0.313,0.198 10 false *a 2.792,1.677 3.104,1.875 0.313,0.198 10 false *b 2.438,0.073 2.75,0.271 0.313,0.198 10 false *c
*a Terminal C
*b Terminal 50
*c Switch Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω
Terminal 50 - Switch Body Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A321559

Inspect the load of the brush spring.

i.

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

18 to 24 N (1.8 to 2.4 kgf, 4.0 to 5.4 lbf)


Minimum spring load:

12 N (1 kgf, 2.7 lbf)


If the load is less than the minimum, replace the starter brush holder assembly.



b.

Check the resistance.

i.
A321560

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) Brush Holder - Negative (-) Brush Holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



c.

Check the brush length.

i.
A341247C01
0.552,1.854 0.865,2.052 0.313,0.198 10 false *a
*a Length


Using a vernier caliper, measure the brush length.

Standard length:

15.5 mm (0.610 in.)


Minimum length:

8.5 mm (0.335 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



Hide 28120 4.INSPECT STARTER YOKE ASSEMBLY

a.

Check the resistance.

i.
A341249C01
0.521,0.542 0.938,0.542 true 2.375,0.656 2.375,0.323 2.375,0.323 2.542,0.323 false 1.167,2 1.333,2 1.333,2 1.583,1.583 true 0.333,0.448 0.646,0.646 0.313,0.198 10 false *a 2.594,0.229 2.906,0.427 0.313,0.198 10 false *b 0.969,1.906 1.281,2.104 0.313,0.198 10 false *c
*a Lead Wire
*b Brush
*c Starter Yoke Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead Wire - Brush Always Below 1 Ω
Starter Yoke Body - Brush 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



b.

Check the brush length.

i.
A341248C01
2.625,1.813 2.938,2.01 0.313,0.198 10 false *a
*a Length


Using a vernier caliper, measure the brush length.

Standard length:

15.5 mm (0.610 in.)


Minimum length:

8.5 mm (0.335 in.)


If the length is less than the minimum, replace the starter yoke assembly.



Hide 28160 5.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.


b.

Check the resistance.

i.
A341250C01
1.229,1.969 1.396,1.969 1.396,1.969 1.396,1.635 false 2.271,1.885 2.104,1.885 2.104,1.885 2.104,1.552 false 1.042,1.875 1.354,2.073 0.313,0.198 10 false *a 2.344,1.792 2.656,1.99 0.313,0.198 10 false *b
*a Segment
*b Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Coil Core 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.
A219195

Check the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



d.

Check the commutator.

i.
A219196

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

30.0 mm (1.18 in.)


Minimum diameter:

29.0 mm (1.14 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


ii.
A102634

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.6 mm (0.0236 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.



Hide 28011 6.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A321563C01
1.979,0.344 2.063,0.542 0.083,0.198 10 false -
V100135

Free
V100136

Lock


Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter clutch sub-assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.