Home › Vehicle Exterior › LIGHTING (EXT) › HEIGHT CONTROL SENSOR
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0470571 HEIGHT CONTROL SENSOR G

LIGHTING (EXT)  HEIGHT CONTROL SENSOR  INSPECTION  


PROCEDURE

Hide 89407B 1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

a.

Check voltage.

i.

Connect 3 dry cell batteries (1.5 V) in series.

NOTICE:

As a voltage of 1.5 V may not be output, do not use a rechargeable dry cell battery.



ii.

Connect the positive (+) end of the dry cell battery to 1 (SHB) and the negative (-) end to 3 (SHG), and apply a voltage of 4.5 V.

NOTICE:

Do not apply a voltage of 6 V or higher between the terminals.


E465517C03
4.875,1.135 5.198,1.323 0.323,0.188 5.313,2.042 5.74,1.229 true 4.708,3.01 5.073,2.146 true 4.844,2.01 4.646,1.427 true 3.958,0.594 4.271,0.75 0.313,0.156 10 false *a 2.708,0.375 3.021,0.531 0.313,0.156 10 false *d 1.083,2.698 1.542,2.906 0.458,0.208 10 false *f 0.313,1.844 0.625,2 0.313,0.156 10 false *c 0.313,2.042 0.625,2.198 0.313,0.156 10 false *b 1.24,3.354 1.552,3.51 0.313,0.156 10 false *g 4.51,3.031 4.969,3.229 0.458,0.198 10 false SHRR 5.781,1.115 6.24,1.313 0.458,0.198 10 false SHG 4.354,1.302 4.813,1.5 0.458,0.198 10 false SHB 4.948,1.156 5.26,1.354 0.313,0.198 10 false V1 0.99,1.656 1.25,1.896 0.26,0.24 10 false *e
*a Component without harness connected
(Rear Height Control Sensor Sub-Assembly RH)
*b Horizontal Position
*c Sensor Standard Position
(0.2 to 12.2° from the horizontal position)
*d (95° from the sensor standard position)
*e Low (full bound)
11.4° from the sensor standard position)
*f High (full rebound)
(35.9° from the sensor standard position)
*g Rebound Side Link Stop Position
(58.0° from the sensor standard position)
- -



iii.

Measure the voltage between the terminals when slowly moving the sensor's link up and down from the sensor standard position while applying voltage.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(V1)Location & Routing

Click Connector(V1)Body>Differential Wire / Frame Wire>Height Control Sensor Sub-Assembly Rear RH

V1-1(SHB) - V1-2(SHRR) Raise the link to the bound side from the sensor standard position (Vehicle height: Low) From 95° down to the link stop position at the bound side Approx. 0.5 V
Full Bound Position 11.4° Approx. 2.0 V
Sensor Standard Position - Approx. 2.5 V
Lower the link to the rebound side from the sensor standard position (Vehicle height: High) Horizontal Position6.2° Approx. 2.8 V
Full Rebound Position Approx. 4.1 V
From 58° down to the link stop position at the rebound side Approx. 4.5 V


If the result is not as specified, replace the rear height control sensor sub-assembly LH.