Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY › 2021.04–2021.07
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0469564 FOG LIGHT ASSEMBLY A

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

If it is not possible to correctly adjust the fog light aim, check the fog light assembly .



PROCEDURE

Hide 1. VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that the vehicle is on a level surface.

·

Inflate the tires to the appropriate pressure.

·

Sit a person of average weight (75 kg, 165 lb) in the driver seat.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.

·

Bounce the vehicle at the corners up and down to stabilize the suspension.

·

Make sure that there is no damage to the body around the headlights.



Hide 2. FOG LIGHT AIMING

a.

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·
E465402C01
0.729,1.313 1.042,1.51 0.313,0.198 10 false *a 1.104,1.885 1.417,2.083 0.313,0.198 10 false *b
*a 90°
*b 25 m or 3 m (82 ft. or 9.84 ft.)


Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (center marks of the fog light) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (center marks of fog light) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.

Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E465404E02
4.417,0.167 6.615,0.469 2.198,0.302 12 false Alignment distance is 3 m: 1,0.167 3.198,0.469 2.198,0.302 12 false Alignment distance is 25 m: 1.135,0.865 1.594,1.063 0.458,0.198 10 false 90° 4.552,0.833 5.01,1.031 0.458,0.198 10 false 90° 1.115,2.938 1.573,3.135 0.458,0.198 10 false 90° 4.552,2.948 5.01,3.146 0.458,0.198 10 false 90° 0.885,0.594 2.26,0.792 1.375,0.198 10 false V RH Line 0.958,1.521 2.333,1.719 1.375,0.198 10 false V LH Line 4.333,0.552 5.708,0.75 1.375,0.198 10 false V RH Line 4.333,1.49 5.708,1.688 1.375,0.198 10 false V LH Line 3.5,2.813 4.875,3.01 1.375,0.198 10 false H Line 0.083,2.792 1.458,2.99 1.375,0.198 10 false H Line 1.208,3.375 2.583,3.573 1.375,0.198 10 false 25 m 4.708,3.375 6.083,3.573 1.375,0.198 10 false 3 m 3.25,1.021 4.167,1.219 0.917,0.198 10 false V Line 6.646,1.021 7.156,1.188 0.51,0.167 10 false V Line

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
E257183C05
1.177,0.292 1.49,0.448 0.313,0.156 10 *a 1.844,0.302 2.156,0.458 0.313,0.156 10 *b 2.479,0.313 2.792,0.469 0.313,0.156 10 *c 2.969,0.875 3.281,1.031 0.313,0.156 10 *d 0.563,1.708 0.875,1.865 0.313,0.156 10 *e
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the aiming marks on the screen.


i.

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center marks of the fog lights).



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

E168642E74
1.958,1.896 2.104,2.417 2.104,2.417 2.333,2.417 false 5.333,1.896 5.49,2.417 5.49,2.417 5.719,2.417 false 2.792,1.917 3.333,2.104 0.542,0.188 10 false 249 mm 6.198,1.917 6.667,2.104 0.469,0.188 10 false 30 mm 0.781,0.083 2.896,0.323 2.115,0.24 12 false Alignment distance is 25 m: 4.208,0.083 6.198,0.313 1.99,0.229 12 false Alignment distance is 3 m: 0.302,1.417 0.75,1.75 0.448,0.333 10 false H Line 3.667,1.427 4.115,1.75 0.448,0.323 10 false H Line 1.531,0.917 2.167,1.25 0.635,0.333 10 false V LH Line 4.844,1.167 5.5,1.5 0.656,0.333 10 false V RH Line 4.833,0.917 5.469,1.229 0.635,0.313 10 false V LH Line 1.521,1.167 2.177,1.5 0.656,0.333 10 false V RH Line 2.375,2.333 2.969,2.635 0.594,0.302 10 false Hot Zone 5.75,2.333 6.344,2.635 0.594,0.302 10 false Hot Zone

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 249 mm (9.80 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 30 mm (1.18 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.

Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver inserted from the service hole.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust the fog light aim, check the fog light assembly installation.


i.

for Standard:

E465405C01
2.646,2.667 2.698,2.333 false 6.375,2.271 6.51,2.104 false 2.573,2.677 2.885,2.875 0.313,0.198 10 false *a 0.146,0.333 0.521,0.573 0.375,0.24 12 false *A 3.865,0.323 4.24,0.563 0.375,0.24 12 false *B 6.26,2.219 6.573,2.417 0.313,0.198 10 false *a
*A w/o Cornering Light *B w/ Cornering Light
*a Aiming Screw - -



ii.

for Aero Type:

E468469C01
2.417,2.458 2.625,2.281 false 6.188,2.521 6.396,2.344 false 2.271,2.448 2.583,2.646 0.313,0.198 10 false *a 6.052,2.49 6.365,2.688 0.313,0.198 10 false *a 0.135,0.385 0.51,0.625 0.375,0.24 12 false *A 3.865,0.385 4.24,0.625 0.375,0.24 12 false *B
*A w/o Cornering Light *B w/ Cornering Light
*a Aiming Screw - -