Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The radio receiver assembly and multi-display controller sub-assembly are connected by the MOST communication lines.

This DTC is stored when a MOST communication error occurs between the radio receiver assembly and multi-display controller sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D5 Rear Seat Entertainment System Disconnected A device that is listed in the MOST network connected device record of the master unit is missing.
·

Multi-display controller sub-assembly power source circuit

·

MOST circuit between radio receiver assembly and multi-display controller sub-assembly

·

Multi-display controller sub-assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

HINT:

For the MOST communication line, the radio receiver assembly is the master unit.


WIRING DIAGRAM

E386884E22
0.885,1.271 1.656,1.5 0.771,0.229 10 false from Battery 1.958,1.469 2.771,1.667 0.813,0.198 10 false RADIO 2.771,1.323 3.156,1.49 0.385,0.167 10 false Q29 2.781,3.677 3.198,3.844 0.417,0.167 10 false Q29 2.844,1.104 3,1.302 0.156,0.198 10 false 1 2.792,3.479 3.042,3.688 0.25,0.208 10 false 14 0.948,5.24 2.865,5.479 1.917,0.24 10 false : MOST Communication Line 3.198,1.302 3.49,1.521 0.292,0.219 10 false +B 3.188,3.667 3.573,3.875 0.385,0.208 10 false GND 3.771,3.208 4.156,3.417 0.385,0.208 10 false MI+ 3.802,3.76 4.188,3.969 0.385,0.208 10 false MI- 3.708,4.344 4.146,4.563 0.438,0.219 10 false SLDI 4.177,3.208 4.594,3.375 0.417,0.167 10 false Q70 4.177,3.771 4.594,3.938 0.417,0.167 10 false Q70 4.188,4.333 4.604,4.5 0.417,0.167 10 false Q70 4.271,2.99 4.427,3.188 0.156,0.198 10 false 5 4.271,3.552 4.427,3.75 0.156,0.198 10 false 6 4.281,4.115 4.438,4.313 0.156,0.198 10 false 7 5.542,3.052 5.698,3.25 0.156,0.198 10 false 2 5.542,3.635 5.698,3.833 0.156,0.198 10 false 3 5.552,4.177 5.708,4.375 0.156,0.198 10 false 4 5.823,3.219 6.208,3.427 0.385,0.208 10 false MO+ 5.813,3.76 6.198,3.969 0.385,0.208 10 false MO- 5.792,4.302 6.271,4.51 0.479,0.208 10 false SLDO 3.083,4.792 4.51,5.167 1.427,0.375 10 false Multi-display Controller Sub-assembly 5.75,4.781 6.125,4.948 0.375,0.167 10 false I139 5.75,4.958 6.698,5.313 0.948,0.354 10 false Radio Receiver Assembly 5.104,4.104 5.521,4.271 0.417,0.167 10 false * 0.365,4.802 2.281,5.042 1.917,0.24 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

B

2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Q29 multi-display controller sub-assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q29)Location & Routing

Click Connector(Q29)Seat>Floor Wire>Multi-Display Controller

Q29-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the I139 radio receiver assembly connector.


b.

Disconnect the Q70 multi-display controller sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I139,Q70)Location & Routing

Click Connector(I139)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(Q70)Seat>Floor Wire>Multi-Display Controller

I139-2 (MO+) - Q70-5 (MI+) Always Below 1 Ω
I139-3 (MO-) - Q70-6 (MI-) Always Below 1 Ω
I139-4 (SLDO) - Q70-7 (SLDI) Always Below 1 Ω
I139-2 (MO+) - Body ground Always 10 kΩ or higher
I139-3 (MO-) - Body ground Always 10 kΩ or higher
I139-4 (SLDO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

4.CHECK MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

Pre-procedure1

a.

Replace the multi-display controller sub-assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT ECU>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

d.

None



A

END (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY IS DEFECTIVE)

B