Home › Suspension › SUSPENSION CONTROL › COMBINATION SWITCH
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0472698 COMBINATION SWITCH G

SUSPENSION CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84012 1.INSPECT INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (DRIVE MODE SWITCH AND 2ND START SWITCH)

a.
C453526C04
1.5,0.167 1.885,0.385 0.385,0.219 2.167,1.354 2.969,1.354 true 0.583,0.583 1.083,0.583 1.083,0.583 1.552,1.135 true 0.073,0.063 0.333,0.271 0.26,0.208 10 false *a 0.125,0.5 0.708,0.667 0.583,0.167 10 false PSW2 3.021,1.281 3.156,1.469 0.135,0.188 10 false E 1.594,0.219 1.906,0.396 0.313,0.177 10 false I88
*a Component without harness connected
(Integration Control and Panel Sub-assembly (Drive Mode Switch and 2nd Start Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I88)Location & Routing

Click Connector(I88)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control and Panel Sub-Assembly

I88-5 (PSW2) - I88-8 (E) Drive mode switch being pushed and held 138 Ω or less
I88-5 (PSW2) - I88-8 (E) Drive mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the integration control and panel sub-assembly (drive mode switch, 2nd start switch and mode select dial).


b.
C453526C02
1.531,0.177 1.896,0.396 0.365,0.219 2.156,1.198 2.865,1.198 true 0.563,1.208 1.271,1.208 true 0.073,0.063 0.333,0.271 0.26,0.208 10 false *a 2.906,1.125 3.281,1.323 0.375,0.198 10 false ILL- 0.26,1.146 0.583,1.354 0.323,0.208 10 false ILL+ 1.615,0.229 1.917,0.396 0.302,0.167 10 false I88
*a Component without harness connected
(Integration Control and Panel Sub-assembly (Drive Mode Switch and 2nd Start Switch))


Apply battery voltage between the terminals of the integration control and panel sub-assembly (drive mode switch, 2nd start switch and mode select dial), and check the illumination condition of the integration control and panel sub-assembly (drive mode switch, 2nd start switch and mode select dial).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → I88-7 (ILL+)
Battery negative (-) → I88-1 (ILL-)
Illuminates


If the result is not as specified, replace the integration control and panel sub-assembly (drive mode switch, 2nd start switch and mode select dial).


Hide 84223A 2.INSPECT TRANSFER POSITION SWITCH

a.
C453531C03
1.5,0.219 1.865,0.427 0.365,0.208 1.99,1.219 2.646,1.219 true 0.771,1.438 1.427,1.438 true 2.708,1.146 3.135,1.365 0.427,0.219 10 false GND2 0.448,1.375 0.802,1.583 0.354,0.208 10 false 2WD 1.583,0.26 1.875,0.469 0.292,0.208 10 false I85 0.073,0.052 0.344,0.292 0.271,0.24 10 false *a
*a Component without harness connected
(Transfer Position Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I85)Location & Routing

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

I85-8 (2WD) - I85-1 (GND2) Transfer position switch L4 66 Ω or less
I85-8 (2WD) - I85-1 (GND2) Transfer position switch H4 10 kΩ or higher


If the result is not as specified, replace the transfer position switch.


b.
C453531C02
1.521,0.219 1.906,0.427 0.385,0.208 1.99,1.438 2.646,1.438 true 0.781,1.229 1.438,1.229 true 2.688,1.365 3.021,1.563 0.333,0.198 10 false ILL- 1.615,0.26 1.896,0.427 0.281,0.167 10 false I85 0.469,1.177 0.813,1.365 0.344,0.188 10 false ILL+ 0.073,0.042 0.344,0.292 0.271,0.25 10 false *a
*a Component without harness connected
(Transfer Position Switch)


Apply battery voltage between the terminals of the transfer position switch, and check the illumination condition of the transfer position switch.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → I85-4 (ILL+)
Battery negative (-) → I85-5 (ILL-)
Illuminates


If the result is not as specified, replace the transfer position switch.