Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM D

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's TCM can then be read.


b.
F102324

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components.


ii.

The powertrain control components (which affect vehicle emissions).


iii.

The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are stored in the TCM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the TCM memory.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle. The scan tool displays DTCs, the freeze frame data and a variety of engine data. The DTCs and freeze frame data can be cleared using the scan tool.




M-OBD


a.

When troubleshooting a Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the TCM can then be read.


b.
F102324

OBD regulations require that the vehicle on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:

i.

The emission control system/components.


ii.

The powertrain control components (which affect vehicle emissions).


iii.

The computer

In addition, the applicable DTCs are stored in the TCM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the TCM memory.




NORMAL MODE AND CHECK MODE


a.

The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent problems (GTS only).



2-TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the TCM memory (1st trip). If the same malfunction is detected during the next driving cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E24
0.354,1.74 2.792,1.99 2.438,0.25 10 false Freeze frame data which can be read 0.698,0.708 1.323,0.906 0.625,0.198 10 false 0.5 sec. 1.333,0.708 1.958,0.906 0.625,0.198 10 false 0.5 sec. 1.99,0.708 2.615,0.906 0.625,0.198 10 false 0.5 sec. 1.823,0.104 2.875,0.396 1.052,0.292 10 false DTC was stored

The GTS records freeze frame data in 5 different instances: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. These sets of data can be used to simulate the vehicle condition around the time when the malfunction occurred. The data may help in finding the cause of the malfunction, or in judging if the DTC was caused by a temporary malfunction.



CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery.


CHECK MIL


a.

Check that the MIL illuminates when the ignition switch is turned to ON.

If the MIL does not illuminate, there is a problem in the MIL circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>MIL Circuit


b.

When the engine is started, the MIL should turn off.