Home › General › SPECIFICATIONS › V35A-FTS FUEL
RM38G0E _V1 General _100727 SPECIFICATIONS _0473256 V35A-FTS FUEL F

SPECIFICATIONS  V35A-FTS FUEL  SERVICE DATA  


FUEL SYSTEM
Standard fuel pressure at idle 196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)
Fuel pressure: for 5 minutes after engine has stopped Standard fuel pressure 98 kPa (1.0 kgf/cm2, 14 psi) or more
Standard fuel pressure (for high pressure) at engine warm up and 3000rpm
(shift lever in N, engine warmed up and A/C off)
2800 to 20000 kPa (28.6 to 203.9 kgf/cm2, 406 to 2900 psi)

FUEL INJECTOR (for Port Injection)
Fuel injector assembly Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω
Standard injection volume 67 to 82 cc (4.1 to 5.0 cu. in.) per 15 seconds
Difference between each fuel injector 15 cc (0.9 cu.in.) or less
Standard fuel drop 1 drop or less per 20 minutes

FUEL INJECTOR (for Direct Injection)
Fuel injector assembly Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 1.34 to 1.64 Ω

FUEL PRESSURE SENSOR

*: The output voltage changes depending on the voltage applied to the terminals.

No. 2 fuel pressure sensor Tester Connection Condition Specified Condition
G4-2(PFL) - G4-3(E2) Pressure not applied to No. 2 fuel pressure sensor Approximately 0.63 to 0.87 V*

FUEL PRESSURE SENSOR (for High pressure)

*: The output voltage changes depending on the voltage applied to the terminals.

Fuel pressure sensor Tester Connection Condition Specified Condition
F4-3(PR) - F4-2(E2) Pressure not applied to fuel pressure sensor Approximately 0.4 to 0.6 V*

FUEL PUMP (for High Pressure)
Fuel pump assembly Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 0.45 to 0.55 Ω

FUEL PUMP
Fuel pump Tester Connection Specified Condition
U - V 0.05 to 3.0 Ω
V - W 0.05 to 3.0 Ω
U - W 0.05 to 3.0 Ω

FUEL SENDER GAUGE ASSEMBLY (for Single Tank Type)

*: The output voltage changes depending on the voltage applied to the terminals.

Fuel sender gauge assembly Tester Connection Condition Specified Condition
V8-2(FE) - V8-3(FR) Float position is F
(upper)
Approximately 4.255 to 4.605 V*
Float position is E
(lower)
Approximately 0.345 to 0.695V*

FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)

*: The output voltage changes depending on the voltage applied to the terminals.

Fuel sender gauge assembly Tester Connection Condition Specified Condition
V8-2(FE) - V8-3(FR) Float position is F
(upper)
Approximately 4.255 to 4.605 V*
Float position is E
(lower)
Approximately 0.345 to 0.695V*
No. 2 fuel sender gauge assembly Tester Connection Condition Specified Condition
V10-2(FE2) - V10-3(FR2) Float position is F
(upper)
Approximately 4.255 to 4.605 V*
Float position is E
(lower)
Approximately 0.345 to 0.695V*