Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.INSPECT SHIFT LOCK CONTROL ECU
If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.
Inspect wire harness:
Disconnect the shift lock control ECU connector.
| *a | Front view of wire harness connector (to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I35)Location & Routingewd_type=routing;type=c;code=I35 |
||
| I35-5 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| I35-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
| *a | Front view of wire harness connector (to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I35)Location & Routingewd_type=routing;type=c;code=I35 |
||
| I35-2 (E) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
2.INSPECT TRANSMISSION CONTROL SWITCH
Disconnect the transmission control switch connector.
for LHD:
| *a | Component without harness connected (Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I73)Location & Routingewd_type=routing;type=c;code=I73 |
||
| I73-4 (IG) - I73-5 (M) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| I73-3 (SFTU) - I73-2 (E) | Shift lever held in "+" (Up-shift) |
Below 1 Ω |
| Shift lever not held in "+" (Up-shift) |
10 kΩ or higher | |
| I73-1 (SFTD) - I73-2 (E) | Shift lever held in "-" (Down-shift) |
Below 1 Ω |
| Shift lever not held in "-" (Down-shift) |
10 kΩ or higher | |
If the result is not as specified, replace the shift lock control unit assembly.
for RHD:
| *a | Component without harness connected (Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I74)Location & Routingewd_type=routing;type=c;code=I74 |
||
| I74-4 (IG) - I74-5 (M) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| I74-1 (SFTU) - I74-2 (E) | Shift lever held in "+" (Up-shift) |
Below 1 Ω |
| Shift lever not held in "+" (Up-shift) |
10 kΩ or higher | |
| I74-3 (SFTD) - I74-2 (E) | Shift lever held in "-" (Down-shift) |
Below 1 Ω |
| Shift lever not held in "-" (Down-shift) |
10 kΩ or higher | |
If the result is not as specified, replace the shift lock control unit assembly.