Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0474716 FUEL SENDER GAUGE ASSEMBLY(for Double Tank Type) G

V35A-FTS FUEL  FUEL SENDER GAUGE ASSEMBLY(for Double Tank Type)  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY

a.

Check the fuel sender gauge assembly output voltage.

i.
A349952C01
2.219,0.667 2.615,0.667 true 1.719,0.615 2.115,0.26 2.115,0.26 2.26,0.26 true 0.042,0.042 0.26,0.25 0.219,0.208 10 false *a 1.615,1.74 1.823,1.938 0.208,0.198 10 false *b 2.656,0.583 2.875,0.802 0.219,0.219 10 false FV 2.302,0.188 2.521,0.406 0.219,0.219 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A487504C01
1,0.125 1.313,0.323 0.313,0.198 0.979,1.917 1.375,1.917 true 0.865,2.99 1.031,2.99 1.031,2.99 1.354,3.125 true 0.635,0.875 1.125,0.875 true 2.24,1.344 2.083,1.344 2.083,1.344 1.771,0.969 true 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 0.875,1.823 1.021,2.031 0.146,0.208 10 false F 0.74,2.896 0.885,3.104 0.146,0.208 10 false E 2.26,1.25 2.49,1.427 0.229,0.177 10 false FE 0.427,0.792 0.646,1 0.219,0.208 10 false FR 1.083,0.156 1.313,0.313 0.229,0.156 10 false V8
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(V8)Location & Routing

Click Connector(V8)Body>Differential Wire / Frame Wire>Fuel Suction with Pump & Gage Tube Assembly

V8-2(FE) - V8-3(FR) Float position is F (upper) Approximately 4.255 to 4.605 V*
V8-2(FE) - V8-3(FR) Float position is E (lower) Approximately 0.345 to 0.695V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage (F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage (E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.



Hide 83320B 2.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

a.

Check the No. 2 fuel sender gauge assembly output voltage.

i.
A349952C03
2.219,0.667 2.615,0.667 true 1.719,0.615 2.115,0.26 2.115,0.26 2.26,0.26 true 0.042,0.042 0.26,0.25 0.219,0.208 10 false *a 1.615,1.74 1.823,1.938 0.208,0.198 10 false *b 2.656,0.573 3.021,0.792 0.365,0.219 10 false FV2 2.302,0.177 2.625,0.385 0.323,0.208 10 false FE2
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV2) and 2 (FE2).

NOTICE:
·

Be careful when connecting the leads, as the No. 2 fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV2) and 2 (FE2).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A487505C01
0.938,0.094 1.333,0.323 0.396,0.229 0.938,2.104 1.333,2.104 true 1.125,2.948 1.292,2.948 1.292,2.948 1.615,3.083 true 0.635,0.875 1.125,0.875 true 2.24,1.344 2.083,1.344 2.083,1.344 1.771,0.969 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 0.844,2.01 0.99,2.219 0.146,0.208 10 false F 0.969,2.865 1.115,3.073 0.146,0.208 10 false E 2.26,1.25 2.604,1.427 0.344,0.177 10 false FE2 0.333,0.781 0.667,0.99 0.333,0.208 10 false FR2 1.01,0.125 1.344,0.333 0.333,0.208 10 false V10
*a Component without harness connected
(No. 2 Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>Differential Wire / Frame Wire>Fuel Pump (Fuel Tank Sub-Assembly)

V10-2(FE2) - V10-3(FR2) Float position is F (upper) Approximately 4.255 to 4.605 V*
V10-2(FE2) - V10-3(FR2) Float position is E (lower) Approximately 0.345 to 0.695V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage (F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage (E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the No. 2 fuel sender gauge assembly.