Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467496 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display)  SYSTEM DESCRIPTION  


DISC PLAYER OUTLINE (w/ Disc Player)


a.

A disc player uses a laser pickup to read digital signals recorded on a disc. By converting the digital signals to analog, it can play music, video and audio.

CAUTION:

Do not look directly at the laser pickup because the disc player uses an invisible laser beam. Be sure to operate the player only as instructed.


NOTICE:
·

Do not disassemble any part of the disc player.

·

Do not apply oil to the disc player.

·

Do not insert anything but a disc into the disc player.




b.

This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:

E119759


c.

This player can play only VCD videos that have any of the following marks: (w/ VCD Player)

E427250


d.

This player can play only DVD videos that have any of the following marks:

E378949


e.

This player can play only DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) that were recorded in video format and that have any of the following marks:

E170098


f.

The following products may not be playable on your player.

·

SACD

·

DTS CD

·

Copy-protected CD

·

Super Video CD

·

DVD audio

·

DVD-RAM



g.

Precautions for use of discs

NOTICE:
·

CD-Rs, CD-RWs, DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) may not be played depending on the recording conditions or characteristics of the discs, or due to damage, dirt or deterioration caused by leaving the discs in the cabin for a long time.

·

Unfinalized CD-Rs, CD-RWs, DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) cannot be played.

·

CD-Rs, CD-RWs, DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs may not play.

·

If there are fingerprints or scratches on a disc, the disc may not play or the disc may skip.

·

Some CD-Rs, CD-RWs, DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) may deteriorate if they are left in the cabin for a long time.

·

Keep CD-Rs, CD-RWs, DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) in an opaque case.

·

SECAM color television standard discs cannot be played.

·

DualDiscs that mate DVD recorded material on one side with CD digital audio material on the other cannot be played.

·

Keep the discs away from dirt. Be careful not to damage the discs or leave fingerprints on them.

·

Hold discs by the outer edge and center hole with the label side up.

·

Leaving the disc exposed halfway out of the slot for a long time after pressing the disc eject button may cause deformation of the disc, making the disc unusable.

·

If discs have adhesive tape, stickers, disc labels or any traces of such labels attached, the discs may not be ejected or player malfunctions may result.

·

Keep the discs away from direct sunlight. (Exposure to direct sunlight may cause deformation of the disc, making the disc unusable.)

·

Do not use odd-shaped discs because these may cause player malfunctions.

·

Do not use discs whose recording portion is transparent or translucent because they may not be inserted, ejected or played normally.

·

Use only 4.7 in. (12 cm) discs.

·

Do not use 3 in. (8 cm) CDs either with or without adaptors.



HINT:
·

When it is cold or raining, if the windows fog up, mist and condensation may form in the player. In such cases, the disc may skip or stop in the middle of play. Ventilate or dehumidify the cabin for a while before using the player.

·

The disc may skip if the player experiences strong vibrations when the vehicle is driven on rough roads or similar uneven surfaces.




h.
I100151

Cleaning

NOTICE:

Do not use a lens cleaner because it may cause a malfunction in the pickup portion of the player.


i.

If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.

NOTICE:
·

Pressing on the disc by hand or rubbing the disc with a hard cloth may scratch the disc surface.

·

Use of solvents such as record spray, antistatic agents, alcohol, benzine, thinners or a chemical cloth may cause damage to the disc, making the disc unusable.






USB AUDIO SYSTEM FUNCTION OUTLINE


a.

The No. 1 stereo jack adapter assembly is equipped with a USB connector. Connecting a USB device or "iPod" to the No. 1 stereo jack adapter assembly allows music files to be played. Not only is it possible to play music from a USB device with audio functions, it is also possible to play MP3, WMA, AAC, WAV (LPCM), FLAC, ALAC or OGG Vorbis music files that are stored on a USB device. In addition, "iPod" control software is installed, allowing file selection from playlists and operation using shuffle mode.

HINT:

Operation through the controls of a USB device or "iPod" cannot be performed while it is connected.



b.

USB audio system compatible devices

i.

USB device

The following device formats can be used:

Compatible USB device formats
·

USB communication format: USB 2.0 HS (480 Mbps)

·

File format: FAT16/32 (Windows)

·

Class: Mass storage class



MP3, WMA, AAC, WAV (LPCM), FLAC, ALAC or OGG Vorbis files written to a USB device with any format other than those listed above may not be played correctly, and their names and folder names may not be displayed correctly.

Items related to standards and limitations are as follows:

·

Maximum directory hierarchy: 8 levels

·

Maximum number of folders in device: 3000 (including the root folder)

·

Maximum number of files in device: 9999

·

Maximum number of files per folder: 255



ii.

"iPod"

1.

for Panasonic Made:

"iPhone", "iPod nano" and "iPod touch" are trademarks of Apple Inc., registered in the U.S. and other countries.

The following "iPhone", "iPod nano", and "iPod touch" devices can be used with this system.

Made for:

-

"iPhone X"

-

"iPhone 8"

-

"iPhone 8 Plus"

-

"iPhone 7"

-

"iPhone 7 Plus"

-

"iPhone SE"

-

"iPhone 6s"

-

"iPhone 6s plus"

-

"iPhone 6"

-

"iPhone 6 plus"

-

"iPhone 5s"

-

"iPhone 5c"

-

"iPhone 5"

-

"iPhone 4s"

-

"iPod touch" (6th generation)

-

"iPod touch" (5th generation)

-

"iPod nano" (7th generation)

HINT:
·

Depending on differences between models or software versions etc., some models might be incompatible with this system.

·

"iPod video" is not supported.




2.

for Pioneer Made:

"iPhone" and "iPod touch" are trademarks of Apple Inc., registered in the U.S. and other countries.

The following "iPhone" and "iPod touch" devices can be used with this system.

Made for:

-

"iPhone X"

-

"iPhone 8"

-

"iPhone 8 Plus"

-

"iPhone 7"

-

"iPhone 7 plus"

-

"iPhone SE"

-

"iPhone 6s"

-

"iPhone 6s plus"

-

"iPhone 5s"

-

"iPhone 5c"

-

"iPhone 5"

-

"iPod touch" (6th generation)

-

"iPod touch" (5th generation)

HINT:
·

Depending on differences between models or software versions etc., some models might be incompatible with this system.

·

"iPod video" is not supported.








USB VIDEO SYSTEM FUNCTION OUTLINE


a.

Playable video file standards

File format MPEG-4, AVI Container, Windows Media Video
Corresponding screen size MAX 1920 x 1080
Corresponding frame rate MAX 60i/30p



HIGH-RESOLUTION SOUND SOURCE OUTLINE


a.

This device supports high-resolution sound sources.


b.

The definition of high-resolution is based on the standards of groups such as the CTA (Consumer Technology Association).


c.

The following formats and media can be used:

Supported formats WAV (LPCM), FLAC, ALAC, OGG Vorbis
Playable media USB



FILE INFORMATION OUTLINE


a.

Playable MP3 file standards

Compatible standard MPEG1 LAYER3, MPEG2 LSF LAYER3
Compatible sampling frequency
·

MPEG1 LAYER3: 32, 44.1, 48 (kHz)

·

MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz)


Compatible bit rate
·

MPEG1 LAYER3: 32 to 320 (kbps)

·

MPEG2 LSF LAYER3: 8 to 160 (kbps)

·

Compatible with VBR


Compatible channel mode Stereo, joint stereo, dual channel, monaural


b.

Playable WMA file standards

Compatible standard WMA Ver. 7, 8, and 9
Compatible sampling frequency 32, 44.1, 48 (kHz)
Compatible bit rate (Only compatible with 2-channel playback)
·

Ver. 7, 8: CBR48 to 192 (kbps)

·

Ver. 9: CBR48 to 320 (kbps)

·

Compatible with VBR




c.

Playable AAC file standards

Compatible standard MPEG4/AAC-LC
Compatible sampling frequency 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 (kHz)
Compatible bit rate
·

8 to 320 (kbps)

·

Compatible with VBR




d.

Playable WAV (LPCM) file standards*

*: Files with a sample rate higher than 48kHz are down-converted to 48kHz/24bit.

Compatible sampling frequency 8/11.025/12/16/22.05/24/32/44.1/48/88.2/96/176.4/192 (kHz)
Compatible bit rate 16/24 (bit)


e.

Playable FLAC file standards*

*: Files with a sample rate higher than 48kHz are down-converted to 48kHz/24bit.

Compatible sampling frequency 8/11.025/12/16/22.05/24/32/44.1/48/88.2/96/176.4/192 (kHz)
Compatible bit rate 16/24 (bit)


f.

Playable ALAC file standards*

*: Files with a sample rate higher than 48kHz are down-converted to 48kHz/24bit.

Compatible sampling frequency 8/11.025/12/16/22.05/24/32/44.1/48/64/88.2/96 (kHz)
Compatible bit rate 16/24 (bit)


g.

Playable OGG Vorbis file standards*

*: Files with a sample rate higher than 48kHz are down-converted to 48kHz/24bit.

Compatible sampling frequency 8/11.025/16/22.05/32/44.1/48 (kHz)
Compatible bit rate
·

32-500 (kbps)

·

Compatible with VBR




h.

ID3 tag, WMA tag, AAC tag, TAG and Vorbis comment

i.

Additional text information called an ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.

HINT:

This player is compatible with ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3.)



ii.

Additional text information called a WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.


iii.

Additional text information called an AAC tag can be input to AAC files. Information such as song titles and artist names can be stored.


iv.

Additional text information called a TAG can be input to WAV (LPCM), FLAC, ALAC files. Information such as song titles and artist names can be stored.


v.

Additional text information called a Vorbis comment can be input to OGG Vorbis files. Information such as song titles and artist names can be stored.



i.

Usable media

i.

USB devices can be used to play MP3/WMA/AAC/WAV (LPCM)/FLAC/ALAC/OGG Vorbis files.



j.

File names

i.

Only files with an extension of ".mp3", ".wma", ".m4a", ".wav", ".flac", ".alac", ".ogg" and ".oga" can be recognized and played as MP3, WMA, AAC, WAV (LPCM), FLAC, ALAC or OGG Vorbis files.


ii.

Save MP3, WMA, AAC, WAV (LPCM), FLAC, ALAC or OGG Vorbis files with an extension of ".mp3", ".wma", ".m4a", ".wav", ".flac", ".alac", ".ogg" or ".oga".

NOTICE:

If non-MP3, non-WMA, non-AAC, non-WAV (LPCM), non-FLAC, non-ALAC or non-OGG Vorbis files are saved with an extension of ".mp3", ".wma", ".m4a", ".wav", ".flac", ".alac", ".ogg" or ".oga", those files may be wrongly recognized as MP3, WMA, AAC, WAV (LPCM), FLAC, ALAC or OGG Vorbis files and played. A loud noise may occur and damage to the speakers may result.





"Bluetooth" OUTLINE


E456881C02
2.406,0.865 2.594,1.031 0.188,0.167 10 *b 3.583,1.896 3.771,2.063 0.188,0.167 10 *c 4.573,1.948 4.969,2.26 0.396,0.313 10 *1 5.563,1.896 5.75,2.063 0.188,0.167 10 *d 4.021,1.385 4.208,1.552 0.188,0.167 10 *e 5.125,1.385 5.313,1.552 0.188,0.167 10 *e 0.073,0.052 0.26,0.219 0.188,0.167 10 *a
*1 Radio Receiver Assembly
(Built-in "Bluetooth" Antenna)
- -
*a Example *b Cellular Network
*c Cellular Phone
("Bluetooth" Compatible Type)
*d Portable Audio Player
("Bluetooth" Compatible Type)
*e "Bluetooth" Wireless Connection - -


a.

"Bluetooth" is a trademark owned by Bluetooth SIG, Inc.


b.

"Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.

HINT:

The communication performance of "Bluetooth" may vary depending on obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity or antenna capacity.



c.

Hands-free function

i.

The "Bluetooth" built-in radio receiver assembly and a "Bluetooth" compatible cellular phone* can be connected using a "Bluetooth" wireless connection. This enables the use of the hands-free function on the cellular phone even if the phone is in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.

*: Some versions of "Bluetooth" compatible cellular phones may not function properly.


ii.

The hands-free function uses a "Bluetooth" wireless connection. A "Bluetooth" wireless connection can be affected by uncertain elements, such as vehicle location, time of day, etc. Therefore, problems related to establishing connection may be caused temporarily by "Bluetooth" connection conditions. It is necessary to check the frequency of occurrence, connection conditions using another cellular phone, etc. when performing diagnosis.


iii.

Compatible hands-free devices

Required "Bluetooth" specifications Ver. 2.0 or higher (Ver. 4.2 or higher recommended)
Compatible profiles
·

HFP (Hands Free Profile) Ver. 1.0 or higher (Ver. 1.7 or higher recommended)*1

·

OPP (Object Push Profile) Ver. 1.1 or higher (Ver. 1.2 or higher recommended)*2

·

PBAP (Phone Book Access Profile) Ver. 1.0 or higher (Ver. 1.2 or higher recommended)*2

·

SPP (Serial Port Profile) Ver. 1.1 or higher (Ver. 1.2 or higher recommended)*3

·

MAP (Message Access Profile) Ver. 1.0 or higher (Ver. 1.2 or higher recommended)*4

·

PAN (Personal Area Networking) Ver. 1.0 or higher*5


Maximum number of hands-free devices that can be registered (including audio devices) 5

*1: This profile is necessary when using the hands-free function.

*2: This profile is necessary when transferring the phonebook data.

*3: This profile is necessary when using the smartphone linked function (w/ Application Link Function).

*4: This profile is necessary when using the message function (w/ SMS/MMS/e-mail Function).

*5: This profile is necessary when using Toyota Online (w/ Toyota Online).


HINT:

The amount of remaining battery charge displayed on the radio receiver assembly may be different from that of the "Bluetooth" device.




d.

"Bluetooth" audio function

i.

The "Bluetooth" built-in radio receiver assembly and a "Bluetooth" compatible portable audio player* can be connected using a "Bluetooth" wireless connection. This enables files stored in the portable audio player to be heard from the vehicle speakers. In addition, operations such as play/stop can be performed directly from the radio receiver assembly.

*: Some versions of "Bluetooth" compatible audio players may not be able to be connected via the "Bluetooth" function, or music may play, but functions available using the radio receiver assembly may be limited.


ii.

Compatible "Bluetooth" audio devices

Required "Bluetooth" specifications Ver. 2.0 or higher (Ver. 4.2 or higher recommended)
Compatible profiles
·

A2DP (Advanced Audio Distribution Profile) Ver. 1.0 or higher (Ver. 1.3 or higher recommended)

·

AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher (Ver. 1.6 or higher recommended)


Maximum number of audio devices that can be registered (including hands-free devices) 5

HINT:
·

When Bluetooth audio and "Miracast" are connected simultaneously, audio output priority varies depending on the specifications of the device.

·

Bluetooth and "Miracast" and other "Wi-Fi" use the same 2.4 GHz band radio waves. As a result, if Bluetooth audio and "Miracast" are connected at the same time some sound skipping etc., may occur.






RADIO DESCRIPTION


a.

Radio frequency band

i.

Radio broadcasts use the radio frequency bands shown in the table below.

E177192E08
0.677,0.25 1.469,0.458 0.792,0.208 10 Frequency 1.875,0.25 2.417,0.417 0.542,0.167 10 30 kHz 5.25,0.25 5.833,0.417 0.583,0.167 10 30 MHz 4.125,0.25 4.677,0.417 0.552,0.167 10 3 MHz 2.979,0.25 3.635,0.417 0.656,0.167 10 300 kHz 6.365,0.25 6.979,0.417 0.615,0.167 10 300 MHz 0.667,0.833 1.458,1.042 0.792,0.208 10 Designation 0.667,1.313 1.448,1.521 0.781,0.208 10 Radio wave 0.667,1.792 1.458,2 0.792,0.208 10 Modulation 2.583,0.833 2.813,1.01 0.229,0.177 10 LF 3.688,0.833 3.917,1.01 0.229,0.177 10 MF 4.854,0.833 5.083,1.01 0.229,0.177 10 HF 5.896,0.833 6.219,1.01 0.323,0.177 10 VHF 3.49,1.313 3.948,1.5 0.458,0.188 10 AM 5.75,1.313 5.979,1.49 0.229,0.177 10 FM 5.552,1.75 6.99,2 1.438,0.25 10 Frequency modulation 3.083,1.75 4.521,2.063 1.438,0.313 10 Amplitude modulation 0.344,2.292 1.594,2.5 1.25,0.208 10 LF: Low Frequency 5.26,2.292 6.979,2.5 1.719,0.208 10 VHF: Very High Frequency 3.74,2.292 5.063,2.5 1.323,0.208 10 HF: High Frequency 1.865,2.292 3.5,2.5 1.635,0.208 10 MF: Medium Frequency



b.

Service area

i.
E177193C06
0.938,2.073 1.104,2.229 0.167,0.156 10 *a 1.771,3.073 1.938,3.229 0.167,0.156 10 *c 1.354,2.563 1.521,2.719 0.167,0.156 10 *b
*a FM (Stereo)
*b FM (Monaural)
*c AM


The service areas of AM and FM broadcasts are vastly different. Sometimes an AM broadcast can be received very clearly but an FM stereo broadcast cannot. FM stereo has the smallest service area, and is prone to pick up static and other types of interference such as noise.



c.

Radio reception problems

HINT:

In addition to static, other problems such as "phasing", "multipath" and "fade out" exist. These problems are not caused by electrical noise, but by the radio signal propagation method itself.


i.
E177194C06
2.375,0.385 2.958,0.708 2.958,0.708 2.958,0.896 false 0.125,0.094 0.333,0.26 0.208,0.167 10 *a 2.896,0.938 3.104,1.104 0.208,0.167 10 *b
*a Phasing
*b Ionosphere


Phasing

AM broadcasts are susceptible to electrical interference and another kind of interference called phasing. Occurring only at night, phasing is the interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off the ionosphere and the other signal is received directly from the transmitter.


ii.
E177195C06
0.103,0.084 0.298,0.237 0.194,0.153 10 *a
*a Multipath


Multipath

Multipath is a type of interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off buildings or mountains and the other signal is received directly from the transmitter.


iii.
E177196C05
0.112,0.045 0.282,0.229 0.17,0.184 10 *a
*a Fade Out


Fade out

Fade out is caused by objects (buildings, mountains and other large obstructions) that deflect part of a signal, resulting in a weaker signal when the object is between the transmitter and vehicle. High frequency radio waves, such as FM broadcasts, are easily deflected by obstructions. Low frequency radio waves, such as AM broadcasts, are less likely to be deflected.



d.

Noise problem

Technicians must have a clear understanding about each customer's noise complaint. Use the following table to diagnose noise problems.

Radio Frequency Noise Occurrence Condition Presumable Cause
AM Noise occurs in a specific area Foreign noise
Noise occurs when listening to an intermittent broadcast An identical program transmitted from multiple towers can cause noise where the signals overlap
Noise occurs only at night Signal phasing
FM Noise occurs while driving in a specific area Multipath resulting from a change in FM frequency



VEHICLE CUSTOMIZATION OUTLINE


a.

Customization of functions can also be performed on the multi-display screen. Refer to Owner's Manual for further information on customizable items for the audio and visual system.

HINT:
·

Items available for customization via the audio and visual system can also be customized by using the GTS.

·

Some customize parameters displayed on the GTS will be displayed on the vehicle customization screen for the audio and visual system. Users can customize these items.





EXPORT / IMPORT MEMORY POINT FUNCTION OUTLINE


a.

This function allows memory points stored in the radio receiver assembly to be registered to another radio receiver assembly. Memory points stored in the radio receiver assembly can be exported to a USB device. Data exported to a USB device can be imported to another radio receiver assembly using a USB device.



AUTOMATIC SOUND LEVELIZER (ASL) FUNCTION OUTLINE


a.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume based upon vehicle speed signals sent from the combination meter assembly.



DIGITAL AUDIO BROADCAST (DAB) FUNCTION OUTLINE (w/ DAB Function)


a.

Digital Audio Broadcast (DAB) is the standard for digital radio. Compared to conventional AM/FM broadcasting, DAB enables higher sound quality radio broadcasting with lower noise when reception conditions change. DAB has an FM-Link function that automatically and temporarily changes the radio to the simultaneously broadcasted FM station if the DAB broadcasting reception level falls.



"Miracast" FUNCTION OUTLINE


a.

About "Miracast"

i.

"Miracast" is a trademark owned by Wi-Fi Alliance, a non-profit industry association.


ii.

"Miracast" uses the "Wi-Fi" connection (P2P function) to display cellular phone and tablet screens on the multi-display and allows for audio on the cellular phone, etc., to be streamed through vehicle speakers.

HINT:
·

While driving only sound playback is supported. Videos are not displayed.

·

When Bluetooth audio and "Miracast" are connected simultaneously, audio output priority varies depending on the specifications of the device.

·

Bluetooth and "Miracast" and other "Wi-Fi" use the same 2.4 GHz band radio waves. As a result, if Bluetooth audio and "Miracast" are connected at the same time some sound skipping and image distortion, etc., may occur.





b.

Supported devices

Supported mobile devices
·

Android cellular phones or tablets certified as "Miracast" compatible devices from the Wi-Fi alliance.

·

For details about "Miracast" compatibility, contact the cellular phone manufacturer.



HINT:
·

Depending on differences between models or software versions etc., some models might be incompatible with this system.

·

This function is not available if the smartphone is not certified by Wi-Fi Alliance as Miracast device.





"Wi-Fi" OUTLINE (w/ "Wi-Fi" Function)


a.

"Wi-Fi" is divided into two functions described in the following table.

Function Description
Station Function* Function that connects the radio receiver assembly to an access point
P2P Function Function that connects the radio receiver assembly to another device directly

*: w/ "Wi-Fi" (Station) Function



b.

"Wi-Fi" is a worldwide wireless communication standard widely used as a short range communication tool.


c.

"Wi-Fi" is a trademark owned by Wi-Fi Alliance, a non-profit industry association.


d.

The radio receiver assembly uses the 2.4 GHz frequency band for "Wi-Fi" communication.

HINT:

The communication performance of "Wi-Fi" may vary depending on obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity or antenna capacity.




TOYOTA ONLINE OUTLINE (w/ Toyota Online)


a.

The following services are available by connecting the audio and visual system to the Toyota portal site via the internet using a cellular phone or "Wi-Fi" network.

·

Online search: New establishments, such as restaurants, bars, etc., that are not registered in the audio and visual system can be set as a destination.

·

Importing memory points: Establishments that were searched for using a personal computer can be set as a destination and can be registered as memory points.


HINT:
·

For known compatible phones, refer to www.my.toyota.eu.

·

Before using Toyota online, access Toyota portal site www.my.toyota.eu via a personal computer etc. and create an account. If the account details are not entered into the radio receiver assembly, this service cannot be used.

·

It is necessary to agree to the terms of service for the search engine on www.my.toyota.eu. Failure to do so may cause problems such as not being able to select the search engine or the screen not transferring to the next screen when "Online search" is selected.

·

Search results may not be displayed if the target establishment is not in the data supplied by the provider or in the map data of the audio and visual system.

·

As the information for a destination set using the Toyota online is supplied by the provider, the audio and visual system may guide to a location that deviates from the actual destination.





TRAFFIC AND PARKING INFORMATION FUNCTION OUTLINE (w/ Toyota Online)


a.

Traffic information and parking lot information can be viewed. There are 2 methods to receive this information.

Priority Method Information
1st Internet by using a cellular phone or "Wi-Fi" network
·

Traffic event

·

Traffic flow prediction


2nd FM RDS-TMC (Radio Data System-Traffic Message Channel)

HINT:
·

Traffic information is displayed only on a map with a scale of 20 km (12 miles) or less.

·

The traffic information display range is 200 km (124 miles) from the current position.

·

The maximum distance is set to 50 km (31 miles). The server will return up to 60 results (maximum distance depends on density of POIs).

·

Detoured route search activates only when traffic information within 200 km (124 miles) exists.

·

If there is traffic information only for traffic congestion, the route may not be changed depending on the distance of the congestion.

·

If there is no available avoidance route, the route may not be changed.

·

Depending on provided data, the "From" and "To" information of the traffic event information may not be displayed.

·

Provided data may differ from the actual situation.





"Apple CarPlay" FUNCTION OUTLINE


a.

The "Apple CarPlay" function is a function that enables the radio receiver assembly to operate applications on a smartphone by connecting the smartphone to the radio receiver assembly using a dedicated cable.

HINT:

Some applications have a display restriction in consideration of safe driving.




"Android Auto" FUNCTION OUTLINE


a.

The "Android Auto" function is a function that enables the radio receiver assembly to operate applications on a smartphone by connecting the smartphone to the radio receiver assembly using a dedicated cable.

HINT:

Some applications have a display restriction in consideration of safe driving.




APPLICATION LINK FUNCTION OUTLINE (w/ Application Link Function)


a.

Application Link is a service that enables applications and content of a cellular phone to be displayed on and operated from the multi-display. As "Bluetooth" communication is used for the communication between a cellular phone and the radio receiver assembly, before using the Application Link service on the audio and visual system, the cellular phone needs to be registered to the audio and visual system as a "Bluetooth" device.

HINT:

Depending on the function, it may be necessary to connect via USB.




DIAGNOSTIC FUNCTION OUTLINE


a.

The audio and visual system has a diagnostic function (the result is indicated on the master unit).



COMMUNICATION SYSTEM


a.

MOST Network Outline

E323018C02
0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.896,0.938 2.208,1.135 0.313,0.198 10 false *b 1.875,2.656 2.188,2.854 0.313,0.198 10 false *b 3.5,1.01 3.813,1.208 0.313,0.198 10 false *c 3.51,2.729 3.823,2.927 0.313,0.198 10 false *c 3.5,1.802 3.813,2 0.313,0.198 10 false *d 0.75,3.271 1.063,3.469 0.313,0.198 10 false *e 6.25,3.281 6.563,3.479 0.313,0.198 10 false *f
*a Example *b MOST Communication Line
*c Shielded *d Wake-up Signal
*e Master Unit *f Slave Unit


i.

Components of the audio and visual system communicate with each other via the MOST network.


ii.

The MOST network uses a shielded twisted pair of wires for its communication lines.


iii.

The master unit of the MOST network is the radio receiver assembly.


iv.

MOST communication lines connect each slave unit centering around the master unit to form a MOST network ring.


v.

The master unit sends a wake-up signal to activate each slave unit connected to the MOST network.

HINT:

If a short or open occurs in the MOST network, communication will be interrupted and the system will not operate normally.




b.

Local Bus Communication Outline

E323019C06
0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 3.479,1.438 3.792,1.635 0.313,0.198 10 false *b 1.688,2.104 2,2.302 0.313,0.198 10 false *c 5.271,2.104 5.583,2.302 0.313,0.198 10 false *d
*a Example *b Local Bus Communication Line
*c Master Unit *d Slave Unit


i.

Components of the audio and visual system communicate with each other via the local bus.


ii.

The local bus uses a twisted pair of wires for its communication lines.


iii.

The master unit of the local bus is the radio receiver assembly.

HINT:
·

The radio receiver assembly has the resistance (108 to 132 Ω) necessary for communication.

·

If a short or open occurs in the local bus circuit, communication is interrupted and the system will not operate normally.





c.

CAN Communication Outline

i.

The audio and visual system uses CAN communication between the radio receiver assembly and ECUs.



d.

AVC-LAN Outline

E323017C01
0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 3.469,1.427 3.781,1.625 0.313,0.198 10 false *b 1.677,2.125 1.99,2.323 0.313,0.198 10 false *c 5.271,2.125 5.583,2.323 0.313,0.198 10 false *d
*a Example *b AVC-LAN Communication Line
*c Master Unit *d Slave Unit


i.

Components of the audio and visual system communicate with each other via AVC-LAN communication.


ii.

The AVC-LAN uses a twisted pair of wires for its communication lines.


iii.

The master unit of the AVC-LAN is the radio receiver assembly.

HINT:
·

The radio receiver assembly has the resistance (60 to 80 Ω) necessary for communication.

·

If a short or open occurs in the AVC-LAN circuit, communication is interrupted and the system will not operate normally.