Home › Engine / Hybrid System › 1GR-FE (EMISSION CONTROL) › AIR SWITCHING VALVE (for Bank 1)
RM38G0E _51 Engine / Hybrid System _101531 1GR-FE EMISSION CONTROL _0474409 AIR SWITCHING VALVE(for Bank 1) G

1GR-FE EMISSION CONTROL  AIR SWITCHING VALVE(for Bank 1)  INSPECTION  


PROCEDURE

Hide 25701B 1.INSPECT NO. 1 EMISSION CONTROL VALVE SET

a.
A489006C01
1.5,0.083 1.917,0.333 0.417,0.25 0.583,0.5 0.75,0.5 0.75,0.5 1.167,1.083 true 2.25,1.083 2.667,0.5 2.667,0.5 2.833,0.5 true 1.573,0.125 2.031,0.323 0.458,0.198 10 false C94 0.167,0.417 0.583,0.583 0.417,0.167 10 false GND 2.917,0.417 3.25,0.583 0.333,0.167 10 false +B
*a Component without harness connected
(No. 1 Emission Control Valve Set)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C94)Location & Routing

Click Connector(C94)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Switching Valve Assembly (for RH Side)

C94-1(GND) - C94-5(+B) 20°C (68°F) 4.5 to 5.5 Ω
C94-1(GND) - Body ground Always 1 MΩ or higher
C94-5(+B) - Body ground


HINT:
·

When measuring the resistance, do not touch terminals 2, 3 or 4.

·

When measuring the resistance make sure that the surface temperature of the No. 1 emission control valve set is 20°C.



If the result is not as specified, replace the No. 1 emission control valve set.


b.
A489007C01
2.771,1.333 2.667,1.333 2.667,1.333 2.177,1.75 true 1.063,2.438 1.063,2.938 true 3.063,1.927 3.24,2.083 0.177,0.156 10 false *a 1,2.979 1.177,3.135 0.177,0.156 10 false *c 2.844,1.26 3.021,1.417 0.177,0.156 10 false *b
*a Air
*b Port A
*c Port B


Check the operation of the No. 1 emission control valve set.

i.

Check that air does not flow from port A to port B.

NOTICE:

Make sure the applied pressure is 30 kPa (0.3 kgf/cm2, 4.4 psi) or less.


If the result is not as specified, replace the No. 1 emission control valve set.


ii.
A489008C01
2.615,2.906 2.51,2.906 2.51,2.906 2.198,3.229 true 1.406,4.479 1.313,4.479 1.313,4.479 1.031,3.99 true 2.667,2.823 2.833,2.99 0.167,0.167 10 false *b 1.458,4.396 1.625,4.563 0.167,0.167 10 false *c 3.063,3.469 3.229,3.635 0.167,0.167 10 false *a
*a Air
*b Port A
*c Port B


Apply battery voltage across terminals 1 and 5.

NOTICE:

When applying voltage, do not touch terminals 2, 3 or 4.



iii.

Check that air flows from port A to port B.

If the result is not as specified, replace the No. 1 emission control valve set.