Home › General › SPECIFICATIONS › 1GR-FE ENGINE CONTROL
RM38G0E _V1 General _100727 SPECIFICATIONS _0475160 1GR-FE ENGINE CONTROL F

SPECIFICATIONS  1GR-FE ENGINE CONTROL  SERVICE DATA  


IGNITON SYSTEM
Spark plug Electrode gap Maximum 1.3 mm (0.0511 in.)
New 1.0 to 1.1 mm (0.0394 to 0.0433 in.)

CAMSHAFT OIL CONTROL VALVE
Camshaft timing oil control valve assembly RH Standard resistance 20 °C (68 °F) 6.9 to 7.9 Ω
Camshaft timing oil control valve assembly LH Standard resistance 20 °C (68 °F) 6.9 to 7.9 Ω

THROTTLE BODY
Throttle with throttle position sensor body assembly Standard resistance 2 (M+) - 1 (M-) 20 °C (68 °F) 0.3 to 100 Ω

MASS AIR FLOW METER
Mass Air Flow Sensor
·

Engine not running

·

30 seconds after ignition switch on


0.63 gm/sec. or less
Standard resistance 1 (THA) - 2 (E2) 0.47 to 19.3 kΩ

CRANKSHAFT POSITION SENSOR
Crankshaft position sensor Standard resistance 1 - 2 Cold
(approximately -10 to 50 °C (14 to 122 °F))
1630 to 2740 Ω
Hot
(approximately 50 to 100 °C (122 to 212 °F))
2065 to 3225 Ω

ENGINE COOLANT TEMPERATURE SENSOR
Engine coolant temperature sensor Standard resistance 1 - 2 20 °C (68 °F) 2.32 to 2.59 kΩ
80 °C (176 °F) 0.310 to 0.326 kΩ

KNOCK SENSOR
Knock sensor (for Bank 1) Standard resistance 1 - 2 25 °C (77 °F) 120 to 280 kΩ
Knock sensor (for Bank 2)

AIR FUEL RATIO SENSOR
Air fuel ratio sensor (for Bank 1) Standard resistance 1 (HA1A) - 2 (+B) 20 °C (68 °F) 1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher
Air fuel ratio sensor (for Bank 2) 1 (HA2A) - 2 (+B) 20 °C (68 °F) 1.6 to 3.2 Ω
1 (HA2A) - 4 (A2A-) Always 10 kΩ or higher

HEATED OXYGEN SENSOR
Heated oxygen sensor (for Bank 1) Standard resistance 1 (TH1B) - 2 (+B) 20 °C (68 °F) 5 to 8 Ω
1 (TH1B) - 4 (E2) Always 10 kΩ or higher
Heated oxygen sensor (for Bank 2) 1 (HT2B) - 2 (+B) 20 °C (68 °F) 5 to 8 Ω
1 (HT2B) - 4 (E2) Always 10 kΩ or higher

RELAY
Standard Resistance
(No. 1 Electronic Fuel Injection Main Relay (EFI-MAIN NO. 1))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Air fuel ratio sensor heater relay (A/F))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Fuel pump relay (FUEL PMP))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Ai valve relay (AI VLV))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(IGP relay (IGP NO. 1))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(NO. 2 IGP relay (IGP NO. 2))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(NO. 3 IGP relay (IGP NO. 3))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Starter relay assembly (ST NO. 1))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Standard Resistance
(Air pump relay (AIR PMP HTR))
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω