Home › General › SPECIFICATIONS › JF2BM TRANSFER / 4WD / AWD
RM38G0E _V1 General _100727 SPECIFICATIONS _0476853 JF2BM TRANSFER / 4WD / AWD F

SPECIFICATIONS  JF2BM TRANSFER / 4WD / AWD  SERVICE DATA  


TRANSFER CASE REAR OIL SEAL
Transfer cover type T oil seal Depth Standard 0.17 to 0.67 mm (0.00670 to 0.0263 in.)

TRANSFER ASSEMBLY
Transfer input shaft Diameter of the input shaft journal surface Minimum 61.002 mm (2.40 in.)
Inside diameter Maximum 46.025 mm (1.81 in.)
Transfer low planetary gear assembly Thrust clearance Standard 0.11 to 0.85 mm (0.00434 to 0.0334 in.)
Maximum 0.85 mm (0.0334 in.)
Radial clearance Standard 0.017 to 0.044 mm (0.000670 to 0.001732 in.)
Maximum 0.044 mm (0.001732 in.)
Rear transfer output shaft Diameter of therear transfer output shaft journals Minimum: A 37.984 mm (1.50 in.)
Minimum: B 41.984 mm (1.65 in.)
Minimum: C 48.984 mm (1.93 in.)
Minimum: D 31.980 mm (1.26 in.)
Transfer drive sprocket sub-assembly Thrust clearance Standard 0.10 to 0.56 mm (0.00394 to 0.02204 in.)
Maximum 0.56 mm (0.02204 in.)
Radial clearance Standard 0.015 to 0.068 mm (0.000591 to 0.002677 in.)
Maximum 0.068 mm (0.002677 in.)
Transfer oil pump rotor set Body clearance Standard 0.09 to 0.16 mm (0.00355 to 0.00629 in.)
Maximum 0.16 mm (0.00629 in.)
Tip clearance Standard 0.04 to 0.16 mm (0.00158 to 0.00629 in.)
Maximum 0.16 mm (0.00629 in.)
Side clearance Standard 0.03 to 0.10 mm (0.00119 to 0.00393 in.)
Maximum 0.10 mm (0.00393 in.)
No. 1 transfer gear shift fork and front drive clutch sleeve Measure the clearance between Maximum 0.84 mm (0.0331 in.)
No. 2 transfer gear shift fork and transfer high and low clutch sleeve Measure the clearance between Maximum 3.40 mm (0.134 in.)

TRANSFER ASSEMBLY (TRANSFER SHIFT ACTUATOR ASSEMBLY)
Item Tester Connection Condition Specified Condition
High-low transfer shift actuator C48-3 (HL1) - C48-6 (GND) After high to low switch is complete 10 kΩ or higher
C48-4 (HL3) - C48-6 (GND) After high to low switch is complete 10 kΩ or higher
C48-5 (HL2) - C48-6 (GND) After high to low switch is complete Below 1 Ω
C48-3 (HL1) - C48-6 (GND) After low to high switch is complete Below 1 Ω
C48-4 (HL3) - C48-6 (GND) After low to high switch is complete 10 kΩ or higher
C48-5 (HL2) - C48-6 (GND) After low to high switch is complete 10 kΩ or higher
Center differential lock actuator C47-3 (CDL) - C47-4 (GND1) After free to lock switch is complete Below 1 Ω
C47-5 (TL3) - C47-4 (GND1) After free to lock switch is complete 10 kΩ or higher
C47-6 (TL2) - C47-4 (GND1) After free to lock switch is complete Below 1 Ω
C47-3 (CDL) - C47-4 (GND1) After lock to free switch is complete 10 kΩ or higher
C47-5 (TL3) - C47-4 (GND1) After lock to free switch is complete Below 1 Ω
C47-6 (TL2) - C47-4 (GND1) After lock to free switch is complete 10 kΩ or higher

CENTER DIFFERENTIAL LOCK SWITCH
Tester Connection Condition Specified Condition

Click Location & Routing(I85)Location & Routing

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

I85-7 (CPU) - I85-1 (GND2) Center differential lock switch pushed and held Below 10 Ω
I85-7 (CPU) - I85-1 (GND2) Center differential lock switch not pushed 10 kΩ or higher

4WD CONTROL SWITCH
Tester Connection Condition Specified Condition

Click Location & Routing(I85)Location & Routing

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

I85-8 (2WD) - I85-1 (GND2) Transfer position switch L4 66 Ω or less
I85-8 (2WD) - I85-1 (GND2) Transfer position switch H4 10 kΩ or higher

MULTI-TERRAIN SELECT SWITCH
Tester Connection Condition Specified Condition

Click Location & Routing(I88)Location & Routing

Click Connector(I88)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control and Panel Sub-Assembly

I88-12 (PSW1) - I88-8 (E) Multi-terrain select switch pushed and held 138 Ω or less
I88-12 (PSW1) - I88-8 (E) Multi-terrain select switch not pushed 10 kΩ or higher