Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.


b.

The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

Function Control Master
(Main ECU to determine controls)
System Related Fail-safe Operation Driver Detectable DTC Detection
(ECU that stored DTC)
Air Conditioning Control
·

Controls various air conditioning functions


Radio and display receiver assembly Air conditioning amplifier assembly
·

The air conditioning related indicators are turned off.

·

If the set air temperature is displayed on an external display device, the set air temperature display is cleared.


Displayed on multi-information display.
·

U0164

·

U0073


(Radio and display receiver assembly)
Clearance Sonar Settings
·

Sets the clearance sonar screen notification condition


Radio and display receiver assembly
·

Clearance warning ECU assembly

·

TCM


The last screen is changed to. Nothing
·

U1110

·

U0073


(Radio and display receiver assembly)
Eco Navigation Display
·

Displays the fuel consumption in 1 minute intervals and displays the average fuel consumption history


Radio and display receiver assembly
·

ECM

·

Brake actuator assembly (No. 2 skid control ECU)

·

Combination meter assembly


·

Fuel consumption calculation cannot be started. After the calculated values are discarded and normal data is received, the 1-minute count is performed again.

·

After the calculated values are discarded and normal data is received, the 1-minute count is performed again.


Nothing
·

U0100

·

U0129

·

U0155

·

U0073


(Radio and display receiver assembly)
Rear View Monitor Control
·

Displays the rear camera view.


Radio and display receiver assembly TCM Only during camera mode, the multi-media display user screen is transitioned to (camera screen is displayed). Nothing -
Smart Camera Function
·

Displays estimated course lines, width extension lines and distance guide lines on the image from the color rear view camera when the vehicle is driven in reverse.


Radio and display receiver assembly
·

Rear television camera assembly

·

ECM

·

TCM


·

Only when camera diagnostic mode is active, the multi-media display user or diagnostic screen is changed to (camera diagnostic screen is displayed).

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is set to the temporary value and the reactive force setting operates as though the camera image is displayed.

·

Only when camera diagnostic mode is active, the multi-media display user is changed to (camera diagnostic screen is displayed).


Nothing
·

U0073

·

U0265


(Radio and display receiver assembly)
Peripheral Monitoring Function
·

ECUs for the multiple camera system, etc.


Radio and display receiver assembly
·

Parking assist ECU

·

ECM

·

TCM


·

Only when camera diagnostic mode is active, the multi-media display user or diagnostic screen is changed to (camera diagnostic screen is displayed).

·

Only when camera malfunction DTC C1610 is output, the current DTC (C1610) is cleared.

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is set to the temporary value and the reactive force setting operates as though the camera image is displayed.

·

Only when camera diagnostic mode is active, the multi-media display user is changed to (camera diagnostic screen is displayed).


Nothing
·

U0073

·

U023B


(Radio and display receiver assembly)
Destination Determination
·

Determines destination information (including steering wheel information), the driver/passenger seats, and uses it for the availability of the XM function


Radio and display receiver assembly Main body ECU (multiplex network body ECU) The destination is determined according to the last received value and the system is operated accordingly (if there is no last received value, the system operates using the default value) Nothing
·

U0140

·

U0073


(Radio and display receiver assembly)
Navigation Coordinated Control (AT/CVT)
·

Predicts the road conditions based on the curve and inclination information and appropriately shifts gears according to the conditions set by the driver, etc.


Radio and display receiver assembly TCM AT/CVT coordinated control related information (curve information, etc.) is sent as the initial value. Nothing
·

U0100

·

U0073


(Radio and display receiver assembly)
Navigation Coordinated Control (Suspension)
·

Improves maneuvering stability by controlling the AVS damping force and electric stability based on the forward curve curvature radius information detected by the navigation ECU.


Radio and display receiver assembly Absorber control ECU Memorization of bump information is prohibited.
Bump information in the process of being memorized is discarded.
However, previously memorized bump information is maintained and bump notification based on this information continues.
Nothing
·

U0132

·

U0073


(Radio and display receiver assembly)
Navigation Coordinated Control (Air Conditioning)
·

Automatically switches between fresh and recirculation modes based on information from the navigation indicating whether the vehicle is in a tunnel.


Radio and display receiver assembly Air conditioning amplifier assembly Nothing Nothing
·

U0164

·

U0073


(Radio and display receiver assembly)
Vehicle Customize Function
·

Changes the behavior and control parameters of various functions (illumination lighting time, etc.)


Radio and display receiver assembly
·

Main body ECU (multiplex network body ECU)

·

Position control ECU assembly

·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)


·

When a phase 4 remote communication usage application is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication.

·

The entrance button is grayed out and cannot be selected when a communication stop occurs, even when customize information is received 1 or more times within 5 seconds after the ignition switch is turned to ON. Customization is performed for the applicable customization item according to diagnostic communication when customize information is not received within 5 seconds after the ignition switch is turned to ON.

·

3 retries are performed (including the first time).


Nothing
·

B15F6

·

B15F8

·

B15F5

·

B15F7

·

U0073


(Radio and display receiver assembly)
CAN Diagnosis Function Radio and display receiver assembly Main body ECU (multiplex network body ECU) Nothing Nothing U0073
(Radio and display receiver assembly)
ESPO
·

Displays the level of "Eco" driving.


Radio and display receiver assembly
·

TCM

·

ECM

·

Brake actuator assembly (No. 2 skid control ECU)


·

The eco level meter display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal. The idling display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal.

·

Current trip data is discarded when a communication stop occurs. New trip data is generated and the function is restarted after the system returns to normal.

·

The eco level meter display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal.


Nothing
·

U0100

·

U0129

·

U0073


(Radio and display receiver assembly)
Brake Hold Operation Control
·

Uses the brake hold operation signal to make driving regulation judgments for the currently viewed video mode (TV, DVD-Video, DVD-VR, iPod Video.) (Allows videos to be displayed when the vehicle is stopped according to brake hold operation).


Radio and display receiver assembly
·

Brake actuator assembly (No. 2 skid control ECU)

·

ECM


The screen display is cleared and the screen is changed to the home screen if a communication stop occurs while video is being displayed. Nothing
·

U0073

·

U0129


(Radio and display receiver assembly)
Meter-linked Function
·

Changes the display based on the customization information set on the combination meter assembly. Outputs the customization information set in the system


Radio and display receiver assembly Combination meter assembly
·

Linked language, unit and accent color: The last valid state is maintained.

·

GS search: Control is performed as if there is an unconfirmed GS search request.

-

The last set value is maintained.

-

If the set item is displayed, it is grayed out so that the item cannot be changed.



Nothing
·

U0073

·

U0155


(Radio and display receiver assembly)
Information Sound Control Function
·

Receives flags from the driving support ECU to operate the alarm and mutes multi-media audio while the alarm is in operation.

·

Receives flags from the forward recognition camera to operate the alarm and mutes multi-media audio while the alarm is in operation.


Radio and display receiver assembly Forward recognition camera Audio muting is canceled.
(Command switch unit is commanded to switch to the normal condition [muting canceled].)
Nothing U0073
(Radio and display receiver assembly)
DMS
·

Enables selection of the vehicle control operation mode during driving


Radio and display receiver assembly Central gateway ECU (network gateway ECU)
·

DMS customize entrance button is not displayed.

·

The screen is changed from the setting screen when the setting screen is displayed.


Nothing U0073
(Radio and display receiver assembly)
Remote Service Function
·

Corresponds with the service center via telematics transceiver to switch to the warning screen, remote immobiliser screen and remote service user screen, and sends customer operation information.


Radio and display receiver assembly Telephone transceiver assembly The remote screen is turned off. Nothing
·

U0073

·

U0198


(Radio and display receiver assembly)
Seat Adjustment Function
·

Seat adjustment is possible on the radio receiver assembly screen


Radio and display receiver assembly Position control ECU assembly Nothing Nothing U0208
(Radio and display receiver assembly)
Air Conditioning Control
·

Controls various air conditioning functions


Radio receiver assembly Air conditioning amplifier assembly
·

The air conditioning related indicators are turned off.

·

If the set air temperature is displayed on an external display device, the set air temperature display is cleared.


Displayed on multi-information display.
·

U0073

·

U0164


(Radio receiver assembly)
Clearance Sonar Settings
·

Sets the clearance sonar screen notification condition


Radio receiver assembly
·

Clearance warning ECU assembly

·

TCM


The last screen is changed to. Nothing
·

U0073

·

U1110


(Radio receiver assembly)
Eco Navigation Display
·

Displays the fuel consumption in 1 minute intervals and displays the average fuel consumption history


Radio receiver assembly
·

ECM

·

Brake actuator assembly (No. 2 skid control ECU)

·

Combination meter assembly


·

Fuel consumption calculation cannot be started. After the calculated values are discarded and normal data is received, the 1-minute count is performed again.

·

After the calculated values are discarded and normal data is received, the 1-minute count is performed again.


Nothing
·

U0073

·

U0100

·

U0129

·

U0155


(Radio receiver assembly)
Rear View Monitor Control
·

Displays the rear camera view.


Radio receiver assembly TCM Only during camera mode, the multi-media display user screen is transitioned to (camera screen is displayed Nothing -
Smart Camera Function
·

Displays estimated course lines, width extension lines and distance guide lines on the image from the color rear view camera when the vehicle is driven in reverse.


Radio receiver assembly
·

Rear television camera assembly

·

ECM

·

TCM


·

Only when camera diagnostic mode is active, the multi-media display user or diagnostic screen is changed to (camera diagnostic screen is displayed).

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is set to the temporary value and the reactive force setting operates as though the camera image is displayed.

·

Only when camera diagnostic mode is active, the multi-media display user is changed to (camera diagnostic screen is displayed).


Nothing
·

U0073

·

U0265


(Radio receiver assembly)
Peripheral Monitoring Function
·

ECUs for the multiple camera system, etc.


Radio receiver assembly
·

Parking assist ECU

·

ECM

·

TCM


·

Only when camera diagnostic mode is active, the multi-media display user or diagnostic screen is changed to (camera diagnostic screen is displayed).

·

Only when camera malfunction DTC C1610 is output, the current DTC (C1610) is cleared.

·

The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is set to the temporary value and the reactive force setting operates as though the camera image is displayed.

·

Only when camera diagnostic mode is active, the multi-media display user is changed to (camera diagnostic screen is displayed).


Nothing
·

U0073

·

U023B


(Radio receiver assembly)
Destination Determination
·

Determines destination information (including steering wheel information), the driver/passenger seats, and uses it for the availability of the XM function


Radio receiver assembly Main body ECU (multiplex network body ECU) The destination is determined according to the last received value and the system is operated accordingly (if there is no last received value, the system operates using the default value) Nothing
·

U0073

·

U0140


(Radio receiver assembly)
Navigation Coordinated Control (AT/CVT)
·

Predicts the road conditions based on the curve and inclination information and appropriately shifts gears according to the conditions set by the driver, etc.


Radio receiver assembly TCM AT/CVT coordinated control related information (curve information, etc.) is sent as the initial value. Nothing
·

U0073

·

U0100


(Radio receiver assembly)
Navigation Coordinated Control (Suspension)
·

Improves maneuvering stability by controlling the AVS damping force and electric stability based on the forward curve curvature radius information detected by the navigation ECU.


Radio receiver assembly Absorber control ECU Memorization of bump information is prohibited.
Bump information in the process of being memorized is discarded.
However, previously memorized bump information is maintained and bump notification based on this information continues.
Nothing
·

U0073

·

U0132


(Radio receiver assembly)
Navigation Coordinated Control (Air Conditioning)
·

Automatically switches between fresh and recirculation modes based on information from the navigation indicating whether the vehicle is in a tunnel.


Radio receiver assembly Air conditioning amplifier assembly Nothing Nothing
·

U0073

·

U0164


(Radio receiver assembly)
Vehicle Customize Function
·

Changes the behavior and control parameters of various functions (illumination lighting time, etc.)


Radio receiver assembly
·

Main body ECU (multiplex network body ECU)

·

Position control ECU assembly

·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)


·

When a phase 4 remote communication usage application is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication.

·

The entrance button is grayed out and cannot be selected when a communication stop occurs, even when customize information is received 1 or more times within 5 seconds after the ignition switch is turned to ON.

·

Customization is performed for the applicable customization item according to diagnostic communication when customize information is not received within 5 seconds after the ignition switch is turned to ON.

·

3 retries are performed (including the first time).


Nothing
·

B15F6

·

B15F8

·

B15F5

·

B15F7

·

U0073


(Radio receiver assembly)
ESPO
·

Displays the level of "Eco" driving.


Radio receiver assembly
·

TCM

·

ECM

·

Brake actuator assembly (No. 2 skid control ECU)


·

The eco level meter display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal.

·

The idling display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal

·

Current trip data is discarded when a communication stop occurs. New trip data is generated and the function is restarted after the system returns to normal.

·

The eco level meter display is turned off when a communication stop occurs. New display data is generated and the function is restarted after the system returns to normal.


Nothing
·

U0073

·

U0100

·

U0129


(Radio receiver assembly)
DSSS
·

Signal information provision service

·

Speed limit information provision service

·

Obstacle information provision service


Radio receiver assembly ECM
·

The following functions which refer to the accelerator opening angle do not operate.

·

Red light warning

·

Temporary stop warning


Nothing
·

U0073

·

U0100


(Radio receiver assembly)
Brake Hold Operation Control
·

Uses the brake hold operation signal to make driving regulation judgments for the currently viewed video mode (TV, DVD-Video, DVD-VR, iPod Video.) (Allows videos to be displayed when the vehicle is stopped according to brake hold operation.)


Radio receiver assembly
·

Brake actuator assembly (No. 2 skid control ECU)

·

ECM


The screen display is cleared and the screen is changed to the home screen if a communication stop occurs while video is being displayed. Nothing
·

U0073

·

U0129


(Radio receiver assembly)
Meter-linked Function
·

Changes the display based on the customization information set on the combination meter assembly. Outputs the customization information set in the system


Radio receiver assembly Combination meter assembly
·

Linked language, unit and accent color: The last valid state is maintained.

·

GS search: Control is performed as if there is an unconfirmed GS search request.

-

The last set value is maintained.

-

If the set item is displayed, it is grayed out so that the item cannot be changed.



Nothing
·

U0073

·

U0155


(Radio receiver assembly)
Information Sound Control Function
·

Receives flags from the driving support ECU to operate the alarm and mutes multi-media audio while the alarm is in operation.

·

Receives flags from the forward recognition camera to operate the alarm and mutes multi-media audio while the alarm is in operation.


Radio receiver assembly Forward recognition camera Audio muting is canceled.
(Command switch unit is commanded to switch to the normal condition [muting canceled].)
Nothing U0073
(Radio receiver assembly)
DMS
·

Enables selection of the vehicle control operation mode during driving


Radio receiver assembly Central gateway ECU (network gateway ECU)
·

DMS customize entrance button is not displayed.

·

The screen is changed from the setting screen when the setting screen is displayed.


Nothing U0073
(Radio receiver assembly)
Seat Adjustment Function
·

Seat adjustment is possible on the radio receiver assembly screen


Radio receiver assembly Position control ECU assembly Nothing Nothing U0208
(Radio receiver assembly)
Meter
·

Displays advice or warning.


Combination meter assembly
·

Absorber control ECU

·

Main body ECU (multiplex network body ECU)

·

Airbag ECU assembly

·

Air conditioning amplifier assembly

·

Headlight ECU sub-assembly LH

·

Multiplex network door ECU

·

Blind spot monitor sensor LH

·

Forward recognition camera

·

Certification ECU (smart key ECU assembly)

·

Stop and start ECU

·

Forward recognition camera

·

Clearance warning ECU assembly

·

Bus buffer ECU

·

Meter mirror sub-assembly

·

ASC

·

Telephone transceiver assembly

·

Certification ECU (smart key ECU assembly)

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Not illuminated.

·

The last valid value is maintained.

·

"--" is displayed for the ambient temperature.

·

Hybrid system indicator does not operate.


Indicator illuminates (amber).
·

U013287

·

U014287

·

U015587

·

U016387

·

U016487

·

U016887

·

U018287

·

U020187

·

U020287

·

U019B87

·

U023087

·

U023387

·

U023587

·

U023A87

·

U032487

·

U110387

·

U110487

·

U111787

·

U113787

·

U111287


(Combination meter assembly)
Tachometer (Conventional)
·

Displays the current engine speed on the headup display using the engine speed signal sent from the engine.


Meter mirror sub-assembly ECM Engine speed: Displays 0 rpm. Nothing U010087
(Meter mirror sub-assembly)
Tachometer (Variable Red Zone)
·

Variably displays the red zone using the red zone engine speed signal sent from the engine.)


Meter mirror sub-assembly ECM Red zone engine speed: Displays 3700 rpm. Nothing U010087
(Meter mirror sub-assembly)
Eco Driving Indicator
·

Displays the Eco driving indicator on the headup display using the Eco zone display condition amount signal sent from the engine.)


Meter mirror sub-assembly ECM Performs control as though Eco zone display condition amount inputs are in the initial condition. Nothing U010087
(Meter mirror sub-assembly)
Dynamic Radar Cruise Control System Display
·

Displays the radar cruise control preceding vehicle, set vehicle distance and set vehicle speed on the headup display using the radar cruise control display signal sent from the engine.


Meter mirror sub-assembly ECM Radar cruise control display (preceding vehicle, merging vehicle, inter-vehicle time): Does not display. Nothing U010087
(Meter mirror sub-assembly)
Speed Management
·

Displays the speed management icon on the head up display using the speed management display request signals sent from the engine.


Meter mirror sub-assembly ECM Does not display. Nothing U010087
(Meter mirror sub-assembly)
BOS
·

Displays the BOS operation condition on the head up display using the BOS display signal sent from the engine.


Meter mirror sub-assembly ECM Does not display. Nothing U010087
(Meter mirror sub-assembly)
DSC
·

Displays the DSC operation condition on the head up display using the DSC display signal sent from the engine.


Meter mirror sub-assembly ECM Does not display. Nothing U010087
(Meter mirror sub-assembly)
RSA-ACC
·

Displays a box around the target sign on the head up display and an arrow next to the set vehicle speed using the RSA-ACC display signals sent from the engine.


Meter mirror sub-assembly ECM
·

RSA-ACC target sign box: Does not display.

·

RSA-ACC arrow: Does not display.


Nothing U010087
(Meter mirror sub-assembly)
Destination Switching
·

Switches the tachometer units and ambient temperature units according to the destination.


Meter mirror sub-assembly Main body ECU (multiplex network body ECU) Control is performed using the last signal received. Nothing U014287
(Meter mirror sub-assembly)
Seat Memory-linked
·

Memorizes and recalls the headup display position in response to the seat position signal sent from the main body ECU [multiplex network body ECU].


Meter mirror sub-assembly Main body ECU (multiplex network body ECU) Control is performed as though there is no seat memory recall.
(Continues to operate the motor and completes the position recall operation if communication loss is assumed during motor operation.)
Nothing
·

U014087

·

U014287


(Meter mirror sub-assembly)
Speedometer
·

Displays the current vehicle speed on the head up display using the current vehicle speed signal sent from the combination meter assembly.


Meter mirror sub-assembly Combination meter assembly
·

Vehicle speed displayed value: Displays 0.

·

Vehicle speed unit: Does not display.


Nothing U015587
(Meter mirror sub-assembly)
Master Caution
·

Displays the master caution icon and messages on the headup display using the master caution display signal sent from the combination meter assembly.


Meter mirror sub-assembly Combination meter assembly Does not display. Nothing U015587
(Meter mirror sub-assembly)
Information
·

Does not display the information icon and messages on the headup display using the information display signal sent from the combination meter assembly.


Meter mirror sub-assembly Combination meter assembly Does not display. Nothing U015587
(Meter mirror sub-assembly)
Display Customization
·

Switches the availability of displayed contents for the headup display by customization through the multimedia information display.


Meter mirror sub-assembly Combination meter assembly Control is performed as though the customize switch is off. Nothing U015587
(Meter mirror sub-assembly)
Language-linked (Combination meter assembly)
·

Switches the language displayed on the head up display [combination meter text] to match the language set by the combination meter assembly.


Meter mirror sub-assembly Combination meter assembly Control is performed using the last signal received. Nothing U015587
(Meter mirror sub-assembly)
Brightness Adjustment
·

Adjusts the meter mirror sub-assembly display brightness by customization through the multimedia information display.


Meter mirror sub-assembly Combination meter assembly
·

Control is performed as though there are no brightness up/down inputs (= the last brightness condition is maintained).

·

The last headlight illumination condition is maintained.


Nothing U015587
(Meter mirror sub-assembly)
Display Position Adjustment
·

Adjusts the meter mirror sub-assembly display position by customization through the multimedia information display.


Meter mirror sub-assembly Combination meter assembly Control is performed as though there are no position up/down inputs (The last position condition is maintained). Nothing U015587
(Meter mirror sub-assembly)
Switching Adjustment
·

Adjusts switching of the meter mirror sub-assembly display in the customization through the multimedia information display.


Meter mirror sub-assembly Combination meter assembly Control is performed as though there are no display switching inputs (= the display is not switched). Nothing U015587
(Meter mirror sub-assembly)
Language-linked (MM)
·

Switches the language displayed on the head up display [multi-media-linked text] to match the language set by the radio receiver assembly.


Meter mirror sub-assembly
·

Radio and display receiver assembly

·

Radio receiver assembly


Control is performed using the last signal received. Nothing U016387
(Meter mirror sub-assembly)
Ambient Temperature/Road Surface Ice Display
·

(Displays the road surface ice display mark and ambient temperature on the headup display using the ambient temperature signal sent from the air conditioning amplifier assembly.


Meter mirror sub-assembly Air conditioning amplifier assembly Ambient temperature: Displays error. Nothing U016487
(Meter mirror sub-assembly)
LDA/LKA
·

Displays the left and right white line marks, steering mark and rest encouragement mark on the meter mirror sub-assembly using the LDA display signal sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera LDA display (white lines, steering mark and rest encouragement mark): Does not display. Nothing U023A87
(Meter mirror sub-assembly)
Road Sign Assist Display
·

Displays traffic signs (such as speed limit signs) using the traffic sign signal sent from the forward recognition camera or object recognition camera.


Meter mirror sub-assembly Forward recognition camera Traffic signs: Do not display. Nothing U023A87
(Meter mirror sub-assembly)
Lane Trace Control System
·

Displays the advanced driving support display matched with the shape of the actual curve (LDA white lines, LTC self-confident wall, ACC preceding vehicle, set vehicle distance. etc.) using the curve number signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Does not display. Nothing U023A87
(Meter mirror sub-assembly)
Pre-collision System Display
·

Displays "BRAKE!" on the headup display using the PCS warning display signal sent from the driving support ECU assembly.


Meter mirror sub-assembly Forward recognition camera PCS warning: Does not display. Nothing U110487
(Meter mirror sub-assembly)
Pedestrian Warning Alert
·

Displays the pedestrian warning alert using the target direction signal sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Pedestrian warning alert: Does not display. Nothing U110487
(Meter mirror sub-assembly)
FCTA
·

Displays the FCTA using the CTA detection signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera FCTA: Does not display. Nothing U110487
(Meter mirror sub-assembly)
Lane Trace Control System
·

Displays the advanced driving support display matched with the shape of the actual curve (LDA white lines, LTC self-confident wall, ACC preceding vehicle, set vehicle distance. etc.) using the curve number signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Does not display. Nothing U110487
(Meter mirror sub-assembly)
LCS
·

Displays the LCS operation condition on the head up display using the LCS planned lane signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Does not display. Nothing U110487
(Meter mirror sub-assembly)
Stop Support System
·

Displays the stop support system operation condition on the HUD using the stop support system display request signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Does not display. Nothing U110487
(Meter mirror sub-assembly)
LVN
·

Displays the LVN "Proceeding Vehicle Start" on the head up display using the LVN display signals sent from the forward recognition camera.


Meter mirror sub-assembly Forward recognition camera Does not display. Nothing U110487
(Meter mirror sub-assembly)
Clearance Sonar
·

Displays the clearance sonar detection condition on the headup display using the clearance sonar display signal sent from the clearance warning ECU assembly.


Meter mirror sub-assembly Clearance warning ECU assembly Clearance sonar (this vehicle, detection bar and frame): Does not display Nothing U111087
(Meter mirror sub-assembly)
ICS
·

Displays the ICS operation condition on the headup display using the ICS display signal sent from the clearance warning ECU assembly.


Meter mirror sub-assembly Clearance warning ECU assembly Does not display. Nothing U111087
(Meter mirror sub-assembly)
Occupant Classification System
·

Acquires information about passengers for deployment of SRS components.


Airbag ECU assembly Brake actuator assembly (No. 2 skid control ECU) SRS components do not deploy.
Hazardous devices are not operated.
A malfunction is sent via CAN communication.
Previously determined values are maintained.
Indicator illuminates (amber). U012987
(Airbag ECU assembly)
Prevention-linked
·

Obtains information from the PCS and uses it for control of device operation (pretensioner, airbag for a side collision, pop-up hood) during a collision.


Airbag ECU assembly
·

DS1

·

Forward recognition camera

·

Millimeter wave radar sensor assembly


Nothing
·

SRS warning light illuminates.

·

Pedestrian protection system warning light illuminates.


·

U023587

·

U023A87

·

U110487


(Airbag ECU assembly)
Brake Assist
·

Estimates the driver's intentions based on the speed and force that the brake pedal is depressed and assists the braking force.


Brake actuator assembly (No. 2 skid control ECU) Airbag ECU assembly Control is continued.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


U012587
(Brake actuator assembly (No. 2 skid control ECU))
TRC/VSC/VDIM
·

Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when starting off.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Control is prohibited.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010187

·

U010087

·

U011087

·

U012587

·

U012687

·

U115087

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
Hill Start Assist Control
·

Maintains the brake oil pressure for 2 seconds when the brake pedal is released when starting off the vehicle from a stop on a slope.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Control is prohibited.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115087

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
Brake Hold
·

Maintains the brake oil pressure when the vehicle is stopped.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Control is prohibited.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115087

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
MCB
·

Applies control to avoid a secondary collision after collision is detected.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


·

Control is prohibited.

·

Control is continued.


·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115087

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
Coordinated Regeneration
·

Performs regenerative brake coordinated control with the hybrid vehicle system.


Brake actuator assembly (No. 2 skid control ECU)
·

Certification ECU (smart key ECU assembly)

·

Airbag ECU assembly

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

EBU


Control is continued.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U029387

·

U115087

·

U011087

·

U110787

·

U012587

·

U012987

·

U025E87


(Brake actuator assembly (No. 2 skid control ECU))
ABS Control
·

Prevents the wheels from locking during sudden stops.


Brake actuator assembly (No. 2 skid control ECU) - ABS control is continued. Nothing -
Brake Assist Control
·

Estimates the driver's intentions based on the speed and force that the brake pedal is depressed and assists the braking force.


Brake actuator assembly (No. 2 skid control ECU) Airbag ECU assembly Brake assist control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

Displays messages on the multi-information display.


U012587
(Brake actuator assembly (No. 2 skid control ECU))
TRC/VSC/VDIM Control
·

Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when starting off.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


TRC/Brake booster with master cylinder assembly (No. 1 skid control ECU)/VDIM control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115C87

·

U115087


(Brake actuator assembly (No. 2 skid control ECU))
Hill Start Assist control
·

Maintains the brake fluid pressure for 2 seconds when the brake pedal is released when starting off the vehicle from a stop on a slope.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Hill start assist control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115C87

·

U115087


(Brake actuator assembly (No. 2 skid control ECU))
Brake Hold Control
·

Maintains the brake fluid pressure when the vehicle is stopped.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Brake hold control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U011087

·

U012587

·

U012687

·

U115087

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
SCB
·

Applies control to avoid a secondary collision after collision is detected.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly


Control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U115087

·

U010087

·

U010187

·

U012587

·

U115C87


(Brake actuator assembly (No. 2 skid control ECU))
Regenerative Brake Coordinated Control
·

Performs regenerative cooperative control with the hybrid vehicle system.


Brake actuator assembly (No. 2 skid control ECU)
·

Certification ECU (smart key ECU assembly)

·

Airbag ECU assembly

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

EBU


Regenerative brake coordinated control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U011087

·

U012587

·

U012987

·

U025E87

·

U110787

·

U115087


(Brake actuator assembly (No. 2 skid control ECU))
Trailer Sway Control
·

Function that suppresses trailer sway when towing a trailer.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Steering sensor


Trailer sway control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U115C87

·

U010187

·

U013087

·

U013487

·

U012587

·

U012687


(Brake actuator assembly (No. 2 skid control ECU))
Shift Interlock Control
·

Function that automatically operates the electronic parking brake when shift position P is selected, and automatically releases the electronic parking brake when shift position D, N, or R is selected.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM


Shift-linked control is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187


(Brake actuator assembly (No. 2 skid control ECU))
Drive Away Release Control
·

With shift position D or R selected, releases the parking brake when the accelerator pedal is depressed.


Brake actuator assembly (No. 2 skid control ECU)
·

ECM

·

TCM

·

Airbag ECU assembly

·

Main body ECU (multiplex network body ECU)


Drive away release is stopped.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold operated indicator light blinks.

·

Brake warning light illuminates.

·

MIL (malfunction indicator lamp) illuminates.

·

Displays messages on the multi-information display.


·

U010087

·

U010187

·

U029387

·

U012587

·

U014087


(Brake actuator assembly (No. 2 skid control ECU))
Electrical Load Control
·

Performs idle up according to the electrical load.


ECM
·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)


Does not perform idle up according to the electrical load. The idling speed changes Nothing
Air Conditioning-linked Control
·

Performs idle up according to the compressor load.

·

Performs air conditioning cut control.


ECM Air conditioning amplifier assembly Air conditioning-linked control does not operate. (Unable to idle up.) Air conditioning does not operate. Nothing
Body Control with Torque Demand
·

Uses excess drive torque control to improve spring behavior (pitch, bounce) due to external factors.)


ECM
·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

4 wheel drive control ECU


Body control with torque demand does not operate.
(Does not use excess drive torque control to improve spring behavior [pitch, bounce] due to external factors.)
Nothing Nothing
Eco Drive Indicator
·

Displays information to the driver that encourages Eco driving.


ECM Combination meter assembly Nothing Information does not display. Nothing
Cruise Control
·

Adjusts engine throttle valve position automatically to maintain vehicle speed.


·

Forward recognition camera

·

ECM


·

ECM

·

Forward recognition camera

·

Combination meter assembly

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Cruise control does not operate. Cruise control does not operate. Nothing
Stop and Start Control
·

Starts/stops the engine according to stop and start control.


ECM Stop and start ECU Stop and start control is prohibited. Stop and start control is prohibited. U110387
(ECM)
Neutral Control
·

Reduces engine load and performs idle up.


TCM
·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Brake actuator assembly (No.2 skid control ECU)

·

Airbag ECU assembly


Neutral control is not performed. Nothing U012987
(TCM)
Stop and Start System
·

Stops the engine when the vehicle is stopped.)


ECO
·

ECM

·

Brake actuator assembly (No. 2 skid control ECU)

·

Steering sensor

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Airbag ECU assembly

·

Combination meter assembly

·

Air conditioning amplifier assembly

·

TCM

·

Clearance warning ECU assembly


·

During Eco-run: It is restarted.

·

Not during Eco-run: Eco-run is prohibited.


Blink lamp.
·

U010087

·

U012687

·

U012987

·

U013187

·

U014087

·

U015187

·

U016487


(ECO)
Automatic Tire Position Display
·

Links TPMS transmitter ID with tire positions based on the wheel speed count from the brakes.


Tire pressure warning ECU and receiver Brake actuator assembly (No. 2 skid control ECU)
·

U012987 is registered.

·

Auto location control is stopped.


Nothing U012987
(Tire pressure warning ECU and receiver)
ATC-4WD SYSTEM
·

Controls the distribution of the front and rear wheel torque in accordance with the driving conditions and road conditions.


4 wheel drive control ECU
·

4 wheel drive control ECU

·

ECM

·

TCM

·

Brake actuator assembly (No. 2 skid control ECU)

·

Steering sensor

·

Air conditioning amplifier assembly


·

4WD control is prohibited.

·

Maintains the last calculated value based on the engine conditions and changes the main control to focus on slip-control.

·

Control is performed based on default value.

·

4WD control is prohibited.


Indicator illuminates (amber).
·

U0073

·

U0100

·

U0129

·

U0126


(4 wheel drive control ECU)
DISCONNTCM SYSTEM+TWIN COUPLING SYSTEM
·

Disconnect system:

Depending on the driving conditions, disengages the propeller shaft to improve fuel economy when it is judged that 4WD is not required.

·

Twin-coupling system:

Controls the distribution of drive torque to the front and rear wheels or left/right of the rear wheels, in accordance with the driving conditions and road conditions.


4 wheel drive control ECU
·

ECM

·

TCM

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Airbag ECU assembly

·

Steering sensor

·

Power steering ECU assembly


·

Maintains the last calculated value based on the engine conditions and changes the main control to focus on slip-control.

·

4WD control is prohibited.

·

Control is performed based on default value.

·

Set to 4WD control (front and rear distribution only), or set to 2WD control.


Indicator illuminates (amber).
·

U010087

·

U012987

·

U012587

·

U012687

·

U013187


(4 wheel drive control ECU)
DISCONNTCM SYSTEM+SINGLE COUPLING SYSTEM
·

Disconnect system:

Depending on the driving conditions, disengages the propeller shaft to improve fuel economy when it is judged that 4WD is not required.

·

Single-coupling system:

Controls the distribution of drive torque to the front and rear wheels in accordance with the driving conditions and road conditions.


4 wheel drive control ECU
·

ECM

·

TCM

·

BRK

·

Brake actuator assembly (No. 2 skid control ECU)

·

Airbag ECU assembly

·

Steering sensor

·

Power steering ECU assembly


·

Maintains the last calculated value based on the engine conditions and changes the main control to focus on slip-control.

·

4WD control is prohibited.

·

Control is performed based on default value.

·

Set to 4WD control (front and rear distribution only), or set to 2WD control.


Indicator illuminates (amber).
·

U010087

·

U012987

·

U012587

·

U012687

·

U013187


(4 wheel drive control ECU)
Sign Display Function
·

Displays signs recognized by the front camera on the meter display or headup display.

*Examples of applicable signs: Speed limit signs, no overtaking/passing signs


Forward recognition camera Combination meter assembly No sign information is displayed on the meter. Displays messages on the multi-information display. U015587
(Forward recognition camera)
Notification Function
·

Notifies the driver if the speed limit displayed by the vehicle exceeds a certain threshold. Notifications: Inverse display, buzzer, etc.

·

Notifies the driver if it detects a passing operation by the driver when a no overtaking/passing sign is output.

·

Notifies the driver if it detects the vehicle being driven into a no entry zone when a no entry sign is recognized.


Forward recognition camera Combination meter assembly The notification function is not performed. Displays messages on the multi-information display. U015587
(Forward recognition camera)
Customization Function
·

Turns RSA on/off when the steering switch is operated, and changes the excessive speed notification method/level, no overtaking/passing notification method, etc.


Forward recognition camera Combination meter assembly Customization settings cannot be changed. Displays messages on the multi-information display. U015587
(Forward recognition camera)
Pre-collision System
·

Recognizes the obstacles, sounds warning buzzer, performs brake assist, brake control to avoid collisions, steering angle combined braking and front side brake assist and warns the driver.


Forward recognition camera
·

ECM

·

Steering sensor

·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

TCM

·

Millimeter wave radar sensor assembly

·

Power steering ECU assembly

·

Power steering ECU with motor assembly


·

Forward pre-collision brake assist and forward/front side pre-collision brake assist are canceled.

·

Forward/front side pre-collision warning buzzer and warnings are canceled.

·

Pre-collision steering is canceled.


·

PCS warning light illuminates.

·

Displayed on multi-information display.


·

U010087

·

U010187

·

U012687

·

U012987

·

U013187

·

U023587

·

U118F87

·

U041881

·

U030051

·

U030057

·

U032851

·

U032857

·

U031951

·

U031957

·

U130651

·

U130657


(Forward recognition camera)
Pre-collision System
·

Senses the preceding vehicle (measures distance) and outputs the result as target information (distance, side position, etc.).


Millimeter wave radar sensor assembly Forward recognition camera Recognition processing is stopped. Nothing
·

U010487

·

U030557


(Millimeter wave radar sensor assembly)
Camera Detection Function
·

Monitors the shift position signal, steering angle signal and vehicle speed, and displays the predicted path guide lines on the screen based on the steering angle when reversing.


Rear television camera assembly
·

Rear television camera assembly

·

ECM

·

TCM

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Blind spot monitor sensor LH

·

Main body ECU (multiplex network body ECU)

·

Steering sensor

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Warning operating: Warning display and buzzer operate as normal.

·

Warning not operating: Warning display and buzzer operate as normal.

·

Warning operating: After operation of warning display and buzzer ends, warnings are prohibited.

·

Warning not operating: Operation of warning display and buzzer are prohibited.

·

Warning operating: Operation of warning buzzer is immediately prohibited (warning display operates normally).

·

Warning not operating: Operation of warning buzzer is prohibited (warning display operates normally).


-
·

U0100

·

U0293

·

U0129

·

U0233

·

U0140

·

U0126

·

U0163


(Rear television camera assembly)
Image Output for Display Control
·

Supplies Power.

·

Displays the multimedia screen.

·

Sets the reaction force pattern.


Rear television camera assembly
·

Main body ECU (multiplex network body ECU)

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Switch icons/guide lines/cooperative display etc. are not displayed.

·

Switch icons on the screen are grayed out.


Alert mark displayed on top of camera screen.
·

U0140

·

U0163


(Rear television camera assembly)
Guide Line Display Control
·

Displays the vehicle path lines related to the steering angle.

·

Controls the screen in accordance with the status of the back door.

·

Adjusts the vehicle path lines in accordance with the mechanism.


Rear television camera assembly
·

Steering sensor

·

Main body ECU (multiplex network body ECU)


·

Parts of the guide lines are not displayed.

·

Guide lines are not displayed.

·

Some switch icons are grayed out.


Alert mark displayed on top of camera screen.
·

U0126

·

U0131

·

U0140


(Rear television camera assembly)
Cooperative Display Control
·

Cooperatively displays sonar information.

·

Cooperatively displays rear cross traffic alert information.


Rear television camera assembly
·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH


Nothing Nothing
·

U1110

·

U0233


(Rear television camera assembly)
Engine/HV Judgment Control
·

Changes the cornering characteristics pattern based on Engine/HV judgement.


Rear television camera assembly
·

ECM

·

TCM


Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0100
(Rear television camera assembly)
2WD/4WD Judgment Control
·

Changes the cornering characteristics pattern based on 2WD/4WD judgement.


Rear television camera assembly
·

ECM

·

TCM


Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0100
(Rear television camera assembly)
EPS Variation Judgment Control
·

Changes the cornering characteristics pattern based on EPS information.


Rear television camera assembly Power steering ECU assembly Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0131
(Rear television camera assembly)
Steering Wheel Judgment Control
·

Changes the switch icon arrangement pattern based on the steering wheel information.


Rear television camera assembly Main body ECU (multiplex network body ECU) Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0140
(Rear television camera assembly)
Destination Judgment Control
·

Changes the display pattern based on the destination information.


Rear television camera assembly Main body ECU (multiplex network body ECU) Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0140
(Rear television camera assembly)
VGRS Existence Judgment Control
·

Changes the cornering characteristics pattern based on VGRS information.


Rear television camera assembly Steering sensor Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0126
(Rear television camera assembly)
Blind Spot Monitor Control
·

Detects neighboring vehicles that are in outer mirror blind spots and notifies drivers of the existence of these vehicles.


Blind spot monitor sensor LH
·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

ECM

·

Steering sensor

·

Main body ECU (multiplex network body ECU)


Blind spot monitor system is stopped.
·

BSM indicator light illuminates (amber).

·

Displays messages on the multi-information display


·

U010087

·

U012987

·

U012687

·

U014087


(Blind spot monitor sensor LH)
Rear Cross Traffic Alert Control
·

Detects vehicles approaching the right or left at the rear of the vehicle when reversing and informs the driver.


Blind spot monitor sensor LH
·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

ECM

·

Steering sensor

·

Main body ECU (multiplex network body ECU)

·

Clearance warning ECU assembly


Rear cross traffic alert system is stopped.
·

RCTA indicator light illuminates (amber).

·

Displays messages on the multi-information display


·

U010087

·

U012987

·

U012687

·

U014087

·

U111087


(Blind spot monitor sensor LH)
Rear Approaching Vehicle Proximity Notification
·

Detects vehicles following in the same lane, and if the possibility of a rear collision is high, rapidly flashes the lights to warn the driver of the vehicle behind.


Blind spot monitor sensor LH
·

Brake actuator assembly (No. 2 skid control ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

ECM

·

Steering sensor


Rear approaching vehicle proximity notification is stopped. Displays messages on the multi-information display
·

U010087

·

U012987

·

U012687


(Blind spot monitor sensor LH)
4 Camera Image Composite Control
·

Acquires the image from the back camera.

·

Acquires the image from the front camera.

·

Acquires the image from the side (right) camera.

·

Acquires the image from the side (left) camera.


Parking assist ECU Rear television camera assembly
·

Rear camera image region is displayed as black.ge region is displayed as black.

·

Front camera image region is displayed as black.

·

Side (right) camera image region is displayed as black.

·

Side (left) camera image region is displayed as black.


Alert mark displayed on top of camera screen.
·

U0265

·

U0267

·

U0268

·

U0266


(Parking assist ECU)
Image Output for Display Control
·

Supplies power.

·

Displays the image on the center display.

·

Sets the reaction force pattern.


Parking assist ECU
·

Main body ECU (multiplex network body ECU)

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Guide lines/cooperative display etc. are not displayed.

·

Switch icons on the screen are grayed out.

·

Switch icons on the screen are grayed out.

·

Switch icons on the screen are grayed out.


Alert mark displayed on top of camera screen.
·

U0140

·

U0163


(Parking assist ECU)
Screen Transition Control
·

Changes the screen based on the vehicle speed.

·

Changes the screen based on the shift position.

·

Controls the screen based on the ABS.

·

Controls the screen based on the PKB.


Parking assist ECU
·

Brake actuator assembly (No. 2 skid control ECU)

·

ECM

·

TCM

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Main body ECU (multiplex network body ECU)


Camera screen is not displayed (some parts may be displayed). Alert mark displayed on top of camera screen.
·

U0100

·

U0129

·

U0140


(Parking assist ECU)
Guide Line Display Control
·

Displays the vehicle path lines related to the steering angle.

·

Controls the screen in accordance with the status of the back door.

·

Adjusts the vehicle path lines in accordance with the mechanism.


Parking assist ECU
·

Steering sensor

·

Main body ECU (multiplex network body ECU)


Driving forward
·

Part of the guide lines are cleared.

·

Guide lines transition switch icon is grayed out.


Driving rearward
·

Part of the guide lines are cleared.


Driving rearward
·

All guide lines for reversing are cleared.

·

Switch icon to transition to guide line display mode is grayed out.


Driving forward
·

Part of the guide lines are cleared.

·

Guide lines transition switch icon is grayed out.


Driving rearward
·

Part of the guide lines are cleared.


Alert mark displayed on top of camera screen.
·

U0126

·

U0131

·

U0140


(Parking assist ECU)
Cooperative Display Control
·

Cooperatively displays sonar information.

·

Cooperatively displays rear cross traffic alert information.

·

Cooperatively displays front cross traffic alert information.


Parking assist ECU
·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH

·

Forward recognition camera


Nothing Nothing
·

U1110

·

U0233

·

U1104

·

U1137


(Parking assist ECU)
Engine/HV Judgment Control
·

Changes the cornering characteristics pattern based on Engine/HV judgement.


Parking assist ECU
·

ECM

·

TCM


Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0100
(Parking assist ECU)
2WD/4WD Judgment Control
·

Changes the cornering characteristics pattern based on 2WD/4WD judgement.


Parking assist ECU
·

ECM

·

TCM


Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0100
(Parking assist ECU)
AT/MT Judgment Control
·

Changes the screen control pattern based on AT/MT judgement.


Parking assist ECU
·

ECM

·

TCM


Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0100
(Parking assist ECU)
EPS Variation Judgment Control
·

Changes the cornering characteristics pattern based on EPS information.


Parking assist ECU Power steering ECU assembly Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0131
(Parking assist ECU)
Steering Wheel Judgment Control
·

Changes the switch icon arrangement pattern based on the steering wheel information.


Parking assist ECU Main body ECU (multiplex network body ECU) Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0140
(Parking assist ECU)
VGRS Existence Judgment Control
·

Changes the cornering characteristics pattern based on VGRS information.


Parking assist ECU Steering sensor Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0126
(Parking assist ECU)
Back Guide Monitor System Judgment Control
·

Changes the detection function pattern based on the back guide monitor information.


Parking assist ECU Rear television camera assembly Performs control based on the signals received before the malfunction occurred. Alert mark displayed on top of camera screen. U0265
(Parking assist ECU)
Key-linked Door Lock
·

Locks and unlocks all doors with a key-linked switch operation.


Main body ECU (multiplex network body ECU) Airbag ECU assembly The driver buckle switch signal is set to "Unconfirmed". Even if the driver seat belt is fastened when the ignition switch is turned to ON, the doors are locked and unlocked using the key-linked switch. U015187
(Main body ECU (multiplex network body ECU))
Shift-linked Auto-lock
·

Locks all the doors when the shift lever is moved from P to a position other than P.


Main body ECU (multiplex network body ECU) ECM The shift position P signal is set to "OFF". All doors are not locked if the following conditions are met:
[Preconditions]
The ignition switch is ON, all doors are closed and the engine is operating.
[Operation conditions]
Shift position is changed from P to other than P.
U010187
(Main body ECU (multiplex network body ECU))
Shift-linked Auto-unlock
·

Unlocks all the doors when the shift lever is moved from a position other than P to P.


Main body ECU (multiplex network body ECU) ECM The shift position P signal is set to "OFF". All doors are not locked if the following conditions are met:
[Preconditions]
The ignition switch is ON, all doors are closed and the engine is operating.
[Operation conditions]
Shift position is changed from P to other than P.
U010187
(Main body ECU (multiplex network body ECU))
Speed-linked Auto-lock
·

Automatically locks all the doors when the system determines that the vehicle is driven.


Main body ECU (multiplex network body ECU) Combination meter assembly The vehicle speed signal (from the combination meter to other systems) is set to "0". All doors are not locked if the following conditions are met:
[Preconditions]
The ignition switch is ON and the engine is operating.
[Operation conditions]
Vehicle speed is 20 km/h (12 mph) or more.
U015587
(Main body ECU (multiplex network body ECU))
Manual Unlock Prohibited
·

Prohibits manual unlock when the vehicle condition has been determined to be in the parked condition after passengers have exited the vehicle and the door lock and door closing operation has been detected.


Main body ECU (multiplex network body ECU) ECM
·

The engine speed is set to "0".

·

The driving possible display is set to "not displayed".


Manual unlock prohibition is not canceled even when the ignition switch is on (READY) in manual unlock prohibition status.
·

U010087

·

U029387


(Main body ECU (multiplex network body ECU))
Auto-lock Switching
·

Switches each auto-lock and auto-unlock function ON/OFF according to user operation.


Main body ECU (multiplex network body ECU) ECM The shift position P signal is set to "OFF". Shift-linked auto-lock and shift-linked auto-unlock on/off switching are performed using the shift P signal ON. Therefore, the on/off switch cannot be operated even if the following procedures are performed:
1) Turn the ignition switch from off to ON.
2) Change the shift position to P.
Press and hold the manual lock (when auto-locked) or unlock (when auto-unlocked) switch for 3 to 7 seconds.
3) After answer back is performed, shift-linked auto-lock/shift-linked auto-unlock will switch between on and off.
U010187
(Main body ECU (multiplex network body ECU))
Wireless Door Lock/Unlock/Auto Relock/Panic/2-times Operation Unlock
·

Locks or unlocks doors according to the smart key switch operation.

·

Relocks doors in order to prevent theft when a lock is unintentionally opened due to a wireless key unlock switch being operated incorrectly.


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly


·

Communication between the remote keyless entry and the body is set to the default value.

·

The remote engine start system control signal is set to "Remote engine start system stopped".


Wireless lock and unlock functions do not operate. U111787
(Main body ECU (multiplex network body ECU))
Smart Door Lock/Unlock
·

Locks or unlocks the doors in response to the smart operations.


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly


·

Communication between the remote keyless entry and the body is set to the default value.

·

The exterior illumination result signal is set to the default value.

·

The remote engine start system control signal is set to "Remote engine start system stopped".


Wireless lock and unlock functions do not operate.
·

U032787

·

U111787


(Main body ECU (multiplex network body ECU))
Wireless Buzzer
·

Sounds the answer back function when the wireless door lock and unlock operations are performed.


Main body ECU (multiplex network body ECU) Certification ECU (smart key ECU assembly)
·

The wireless buzzer sounding signal is set to the default value.

·

The wireless buzzer volume is set to "Maximum".


No answer back operates when the wireless door lock or unlock function operates. U016887
(Main body ECU (multiplex network body ECU))
Smart Back Door Opener
·

Unlocks and unlatches the trunk when the trunk open switch is pressed and held with the trunk locked.


Main body ECU (multiplex network body ECU) Certification ECU (smart key ECU assembly)
·

The trunk and back door opener switch signal is set to "OFF".

·

Communication between the remote keyless entry and the body is set to the default value.


The back door does not unlatch even when the back door open switch is pressed and held with the back door locked. U016887
(Main body ECU (multiplex network body ECU))
Back Door Opener
·

Unlatches the trunk according to the open switch being pressed on the instrument panel.


Main body ECU (multiplex network body ECU)
·

Combination meter assembly

·

ECM


·

The vehicle speed is set to "0".

·

The trunk operation is started and the answer back (hazard warning light/buzzer) is not operated.


The back door does not unlatch even when the open switch on the instrument panel is pressed and held.
·

U015587

·

U010187


(Main body ECU (multiplex network body ECU))
Interior Illumination OFF at Engine Start
·

Turns off the dome light, foot light, door trim and instrument panel in order to prevent light flickering caused by reduced voltage due to cranking when the user starts the engine.


Main body ECU (multiplex network body ECU) ECM The starter signal is set to "non-operating". No lights turn off when cranking. U010187
(Main body ECU (multiplex network body ECU))
Washer Nozzle Heater
·

Prevents the washer nozzle from freezing due to low temperature.


Main body ECU (multiplex network body ECU) Air conditioning amplifier assembly Ambient temperature data (display) is set to "Unconfirmed". The nozzle heater does not operate even if the ambient temperature is 5 °C (41 °F) or less. U016487
(Main body ECU (multiplex network body ECU))
Seat and Mirror Control
·

Memorizes and recalls memory switch

·

Memorizes and recalls memory call


Main body ECU (multiplex network body ECU)
·

Position control ECU assembly

·

Multiplex tilt and telescopic ECU

·

Outer mirror control ECU assembly LH

·

Outer mirror control ECU assembly RH

·

Certification ECU (smart key ECU assembly)


·

The seat, tilt and telescopic, etc., are commanded to stop operating.

·

Memory call registration: The operation is stopped due to timing out while waiting for the verification results.


Memory call registration: The operation is stopped due to timing out while waiting for the verification results.
·

U016887

·

U019987

·

U020087

·

U020887

·

U020987

·

U111587


(Main body ECU (multiplex network body ECU))
Dome Light
·

Dome light illuminates when the user approaches the one of the doors while holding the smart key.


Main body ECU (multiplex network body ECU) Certification ECU (smart key ECU assembly) The exterior illumination result signal is set to the default value. Outside handle light and dome light do not illuminate when approaching one of the doors while holding the smart key. U016887
(Main body ECU (multiplex network body ECU))
Interior Illumination Dimming
·

Dims the instrument panel, foot light and inside handle illumination when starting to drive.


Main body ECU (multiplex network body ECU) ECM The shift position P signal is set to "OFF". The interior illumination does not dim when changing the shift position from P to other than P. U010187
(Main body ECU (multiplex network body ECU))
Reverse-linked Mirror
·

Changes the direction of the outer mirror when the shift lever is moved to R.


Main body ECU (multiplex network body ECU) ECM The shift position P signal is set to "OFF". The reverse-linked mirror does not operate when the shift position is in R. U010187
(Main body ECU (multiplex network body ECU))
Alarm Function
·

Performs the alarm operation when the system determines that there has been an unauthorized entry into the vehicle based on changes in the states of the door courtesy light switches, etc., while the alarm is set.


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly

·

ECM


·

The push start switch signal is set to "OFF".

·

The push start key signal is set to "Push start system control key unconfirmed".

·

The remote engine start system control signal is set to "Remote engine start system stopped".

·

The engine speed is set to "0".

·

The driving possible display is hidden.


·

If the push start switch is pressed before the alarm is set, the alarm is not set. However, the alarm is set when a certain amount of time elapses after a wireless lock operation is performed.

·

While the warning alarm is sounding, the warning alarm is not canceled even if a smart key registered to the vehicle is certified and the push start switch is pressed.

·

When the warning alarm is sounding, it is not canceled even after the engine is started.


·

U010087

·

U012087

·

U110787

·

U111787


(Main body ECU (multiplex network body ECU))
Battery Saver
·

Cancels illumination commands sent to the interior illumination and stops the power supply to suppress battery depletion when the system determines that the vehicle is parked.


Main body ECU (multiplex network body ECU) Certification ECU (smart key ECU assembly) The exterior illumination result signal is set to the default value. During battery protection, battery protection is not canceled and illumination does not turn on even when the user approaches a door while carrying the smart key. U016887
(Main body ECU (multiplex network body ECU))
Light Auto Turn Off System
·

Automatically turns lights off when exiting the vehicle with the lights still turned on.


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Steering sensor


·

Communication is set to the default value.

·

Previous values for the light combination switch location information is maintained.


When the wireless key lock switch is pressed while waiting for the light off delay time (30 seconds) with all the doors locked, the headlights do not turn off.
·

U012687

·

U016887


(Main body ECU (multiplex network body ECU))
Follow Me Home
·

Illuminates the headlights according to a timer if the light combination switch is moved from the OFF or AUTO position to operate the turn signal after the ignition switch is turned off.


Main body ECU (multiplex network body ECU) Steering sensor Previous values for the light combination switch location information is maintained. The headlights do not turn on via headlight illumination extension operation. U012687
(Main body ECU (multiplex network body ECU))
Automatic Light Control
·

Automatically illuminates/turns off the headlights and taillights according to the automatic light control brightness information when the ignition switch is turned ON and the light combination switch is moved to the AUTO position.


Main body ECU (multiplex network body ECU) Steering sensor Previous values for the light combination switch location information is maintained. Automatic light control does not switch according to light combination switch operation. U012687
(Main body ECU (multiplex network body ECU))
Daytime Running Light
·

Illuminates/turns off the daytime running lights after determining whether the vehicle is being driven.


Main body ECU (multiplex network body ECU) Brake actuator assembly (No. 2 skid control ECU) The electric parking brake lock condition is set as "Condition unknown". For daytime running lights other than the Scandinavian specification, the daytime running lights do not illuminate even if the parking break is released. U110687
(Main body ECU (multiplex network body ECU))
Front Fog/Rear Fog
·

Illuminates/turns off the front fog and rear fog lights according to light combination switch operation.


Main body ECU (multiplex network body ECU) Steering sensor Front fog/rear fog light switch position information for the light combination switch is set to "OFF". Front fog/rear fog lights cannot illuminate according to light combination switch operation. U012687
(Main body ECU (multiplex network body ECU))
LED Headlight Warning
·

Notifies the driver when the system detects an open circuit in the LED headlight or a driver malfunction.


Main body ECU (multiplex network body ECU)
·

ECM

·

Headlight ECU sub-assembly LH


·

The engine speed is set to "0".

·

The driving possible display is hidden.

·

Previous values for the LED malfunction signal are maintained.


·

Even if the low beams are on when the engine is started while an LED malfunction is detected, the LED headlight indicator does not illuminate.

·

Even if the low beams are on with the ignition switch on (READY) while an LED malfunction is detected, the LED headlight indicator does not illuminate.


·

U010087

·

U024187


(Main body ECU (multiplex network body ECU))
Automatic High Beam
·

Detects the headlights of an oncoming vehicle and automatically switches the headlights from high beams to low beams when the high beams are illuminated and the automatic high beam function is operating.


Main body ECU (multiplex network body ECU) Steering sensor Automatic high beam switch position information for the light combination switch is set to "OFF". Automatic high beam control cannot operate according to light combination switch operation. U012687
(Main body ECU (multiplex network body ECU))
Adaptive High Beam
·

Detects oncoming vehicles and automatically switches the headlight light distribution when the high beams are illuminated and the adaptive high beam function is operating.


Main body ECU (multiplex network body ECU) Steering sensor High beam switch position information for the light combination switch is set to "OFF". Adaptive high beam control cannot operate. U012687
(Main body ECU (multiplex network body ECU))
Wiper-linked Headlight Illumination
·

Automatically illuminates the headlights with the light combination switch in the AUTO position and the wipers operating.


Main body ECU (multiplex network body ECU) Steering sensor Previous values for the light combination switch automatic location information is maintained. Even if the wiper-linked headlight illumination control conditions are met, the headlights do not illuminate, or even if the wiper-linked headlight illumination control conditions are not met (the light combination switch is not in the AUTO position), the headlights illuminate. U012687
(Main body ECU (multiplex network body ECU))
Hospitality Clearance
·

Illuminates the clearance lights according to wireless key or smart handle door unlock operation with the light combination switch in the AUTO position.


Main body ECU (multiplex network body ECU) Steering sensor Previous values for the light combination switch automatic location information is maintained. Clearance lights do not operate even when the hospitality clearance control conditions are met. U012687
(Main body ECU (multiplex network body ECU))
Light Reminder
·

Sounds a buzzer to remind the user to turn off the lights when the ignition switch is turned off and the driver door is opened with the light combination switch in TAIL or HEAD position and the taillights illuminated.


Main body ECU (multiplex network body ECU) Steering sensor Previous values for the light combination switch location information is maintained. Headlights and taillights cannot be switched between on and off according to light combination switch operation. U012687
(Main body ECU (multiplex network body ECU))
Automatic Display Dimming
·

Determines the time of day (daytime, twilight to nighttime) according to the light sensor signal and interior illumination state as time changes from twilight to nighttime and links with the tail cancel switch state to dim the interior displays and indicators.


Main body ECU (multiplex network body ECU) Combination meter assembly The tail cancel signal is set to "OFF". Headlights and taillights cannot be switched between on and off according to light combination switch operation. U015587
(Main body ECU (multiplex network body ECU))
Power Window Operation Permission
·

Permits operation of the power windows for 43 seconds after the ignition switch is turned off.


Main body ECU (multiplex network body ECU) ECM
·

The engine speed is set to "0".

·

The driving possible display is hidden.


Power window operation is not permitted even when the engine is started.
(Ignition switch ON is one of the OR conditions required for operation permission in practice.)
U010087
(Main body ECU (multiplex network body ECU))
Wireless-linked Power Window
·

Operates the power window according to wireless key operation.


Main body ECU (multiplex network body ECU) Certification ECU (smart key ECU assembly) Communication is set to the default value. When the ignition switch is turned off, power windows cannot be operated up or down according to wireless key switch operation. U016887
(Main body ECU (multiplex network body ECU))
Open Window Warning
·

Displays the open window warning on the combination meter and sounds a single buzzer to remind the user to close the windows when exiting the vehicle with the windows open.


Main body ECU (multiplex network body ECU) Combination meter assembly Nothing When the ignition switch is turned off, power windows cannot be operated up or down according to wireless key switch operation. Nothing
Sliding Roof Open Warning
·

Displays the sliding roof open warning on the combination meter and sounds a single buzzer to remind the user to close the sliding roof when exiting the vehicle with the sliding roof open.


Main body ECU (multiplex network body ECU) Combination meter assembly Nothing Even if the ignition switch is turned off and the driver door is opened with a window open, the open window warning is not displayed on the meter. Nothing
Wiper Control
·

Operates the wipers according to wiper combination switch operation.


Main body ECU (multiplex network body ECU)
·

Wiper ECU (LIN)

·

Rain sensor (LIN)


·

Wiper operation is allowed when the wiper combination switch operation position is changed to wiper Hi mode.

·

Previous values for the wiper combination switch location information are maintained.


The wiper and washer do not operate according to wiper combination switch operation. U012687
(Main body ECU (multiplex network body ECU))
Tire Pressure Warning
·

Displays the tire pressure warning on the combination meter.


Main body ECU (multiplex network body ECU) Combination meter assembly Nothing The tire pressure warning is not correctly displayed on the meter.
(According to the fail-safe specification of the meter)
Nothing
Auto Electrical Mirror
·

Retract/return the outer mirrors in conjunction with the doors locking/unlocking.


Main body ECU (multiplex network body ECU)
·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly


·

Communication is set to the default value.

·

The remote engine start system control signal is set to "Remote engine start system stopped".


When the vehicle is driven at night with the headlight switch off or in the TAIL position, the light illumination reminder is not displayed on the multi-information display.
·

U016887

·

U111787


(Main body ECU (multiplex network body ECU))
User Customization
·

Makes it possible to customize main body ECU functions on the navigation screen.


Main body ECU (multiplex network body ECU) Nothing Nothing Main body ECU functions cannot be customized on the navigation screen. U016387
(Main body ECU (multiplex network body ECU))
Rear Sunshade Reverse-linked
·

Retracts the rear sunshade when the shift lever is moved to R.


Main body ECU (multiplex network body ECU) ECM
·

The shift position P signal is set to "OFF".

·

The shift position R signal is set to "OFF".


Nothing U010187
(Main body ECU (multiplex network body ECU))
Headlight Illumination Reminder
·

Reminds the user to illuminate the headlights when the vehicle is driven at night with the headlights turned off.


Main body ECU (multiplex network body ECU) Combination meter assembly
·

The vehicle speed signal (from the combination meter to other systems) is set to "0".

·

The response type is set to unused.

·

Response contents are set to unused.


When the vehicle is driven at night with the headlight switch off or in the TAIL position, the light illumination reminder is not displayed on the multi-information display. U015587
(Main body ECU (multiplex network body ECU))
Headlight Turn Off Reminder
·

Reminds the user to turn off the headlights when the headlight switch is on and 5 minutes elapse after the ignition switch is turned off.


Main body ECU (multiplex network body ECU) Combination meter assembly
·

The response type is set to unused.

·

Response contents are set to unused.


Even if the steering pad switch return button is pressed within 6 seconds of the reminder display, the reminder does not disappear. U015587
(Main body ECU (multiplex network body ECU))
Wiper-linked Window Close
·

Reminds the user to close the windows when the wipers are operating.


Main body ECU (multiplex network body ECU)
·

Combination meter assembly

·

Certification ECU (smart key ECU assembly)


·

The response type is set to unused.

·

Response contents are set to unused.

·

Communication is set to the default value.

·

The response type is set to unused.

·

Response contents are set to unused.

·

Communication is set to the default value.


·

Even if a window is opened while the wipers are operating, the reminder to close the windows is not displayed on the multi-information display.

·

When the wireless/smart-linked power window UP/DOWN operation is performed, the reminder does not disappear.


·

U015587

·

U015587


(Main body ECU (multiplex network body ECU))
Power Window Lock Release Notification
·

Reminds the user to release the power window lock switch when the power window lock switch is ON and the power window switch is operated.


Main body ECU (multiplex network body ECU) Combination meter assembly Nothing The power window lock switch release reminder is not displayed in the middle of the multi-information display even when the power window lock switch is on and the power window switch is operated. U015587
(Main body ECU (multiplex network body ECU))
Door Open-linked Wiper Stop
·

Stops the wipers when a door is opened while the wipers are operating.


Main body ECU (multiplex network body ECU)
·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

ECM


·

The electric parking brake lock condition is set as "Condition unknown".

·

The shift position P signal is set to "OFF".

·

The electric parking brake lock condition is set as "Condition unknown".

·

The shift position P signal is set to "OFF".


·

When the ignition switch is turned to ON, the wipers are operating in AUTO mode and the shift lever is in P, even if the driver or passenger door is opened, the wipers do not stop.

·

When the ignition switch is turned to ON, the wipers are operating in AUTO mode and the electric parking brake is locked, even if the driver or passenger door is opened, the wipers do not stop.


·

U010187

·

U110687


(Main body ECU (multiplex network body ECU))
Tunnel Mode Notification
·

Displays a reminder, on the multi-information display, to close the windows, if the power windows are open when the vehicle is approaching a tunnel. User operation closes windows at all seats.


Main body ECU (multiplex network body ECU)
·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

ECM

·

Radio and display receiver assembly

·

Radio receiver assembly


·

"No Tunnel" is set for when tunnels are 150 meters ahead.

·

"No Tunnel" is set for when tunnels are 500 meters ahead.

·

"No Tunnel" is set for when tunnels are 1000 meters ahead.

·

"No Tunnel" is set for when tunnels are 5000 meters ahead.

·

The vehicle speed signal is set to "10 km/h".

·

The steering angle is set to "0 deg".

·

Previous values for the shift position signal are maintained.


The close window reminder is not displayed according to the tunnel mode notification.
·

U010187

·

U012987

·

U016387


(Main body ECU (multiplex network body ECU))
Notification to Close Windows While Driving at High Speeds
·

Displays a reminder, on the multi-information display, to close the windows, if the power windows are open after the vehicle exceeds 80 km/h for a specified length of time. User operation closes windows at all seats.


Main body ECU (multiplex network body ECU)
·

Brake booster with master cylinder assembly (No. 1 skid control ECU)

·

Combination meter assembly

·

ECM


·

The vehicle speed signal is set to "10 km/h".

·

The steering angle is set to "0 deg".

·

The turn SW signal is set to "OFF".

·

Previous values for the shift position signal are maintained.


Nothing
·

U010187

·

U012987


(Main body ECU (multiplex network body ECU))
Diagnostic / C-BEST
·

Diagnostic phase 4 communication.


Nothing Main body ECU (multiplex network body ECU) Diagnostic mode is exited. Nothing Nothing
Air Conditioning Control
·

Corrects the engine speed by performing idle up, etc.

·

Adjusts the air temperature, airflow mode and airflow volume according to the engine coolant temperature.

·

Performs the engine coolant temperature map calibration and switches compressor lock judgment value based on engine type.


Air conditioning amplifier assembly ECM
·

Control is performed using the default engine coolant temperature value 80 °C (176 °F).

·

Control is performed using the default value for the engine type.


Nothing U010087
(Air conditioning amplifier assembly)
Compressor Control
·

Determines whether the compressor is locked according to engine speed.


Air conditioning amplifier assembly ECM Control is performed using the default engine speed value (0 rpm). Nothing U010087
(Air conditioning amplifier assembly)
Simple Load Control
·

Limits electrical load control according to the load control level.


Air conditioning amplifier assembly Power steering ECU assembly The previous state is maintained (during a reset, there is no load control). Nothing U013187
(Air conditioning amplifier assembly)
Panel Control
·

Controls the air conditioning system operation condition and panel switch IND output according to the panel switch operation information.


Air conditioning amplifier assembly
·

Radio and display receiver assembly

·

Radio receiver assembly


The panel switch is turned to off, exhaust gas availability information is maintained. Nothing U016387
(Air conditioning amplifier assembly)
Remote Start Control
·

Controls the air conditioning system operation state according to remote start information.


Air conditioning amplifier assembly
·

Main body ECU (multiplex network body ECU)

·

Bus buffer ECU


Remote start control is not performed. Nothing -
Ambient Temperature Adjustment Control
·

Switches the air conditioning system operation condition and adjusts the ambient temperature display output value according to the vehicle speed information.


Air conditioning amplifier assembly Combination meter assembly Control is performed using the default vehicle speed value (0 km/h). Nothing U0155 87
(Air conditioning amplifier assembly)
Air Conditioning ECO Control
·

Performs ECO-mode control.


Air conditioning amplifier assembly TCM The previous state is maintained (After a reset, control is performed normally). Nothing -
Air Conditioning Screen Operations in TOYOTA Multi-Operation Touch
·

Changes the air conditioning settings by using air conditioning screen operations in TOYOTA Multi-Operation Touch.


Air conditioning amplifier assembly Integration control sub-assembly The previous state is maintained. Nothing U111487
(Air conditioning amplifier assembly)
Pre-Air Conditioning Control
·

Controls pre-air conditioning by using the smart key.


Air conditioning amplifier assembly Certification ECU (smart key ECU assembly) Power mode is set to the default value (normal mode) and pre-air conditioning is stopped. Nothing U016887
(Air conditioning amplifier assembly)
Keyless Entry Function
·

System that stops keyless lock operations when the power source mode is on or a door is open, and performs keyless unlock, PSD (left or right side) keyless open, luggage compartment keyless unlock, and hands free power back door operation.


Certification ECU (smart key ECU assembly)
·

Telephone transceiver assembly

·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU


Nothing Nothing
·

U014087

·

U111787

·

U020287

·

U020187

·

U023087


(Certification ECU (smart key ECU assembly))
Keyless Lock Function
·

System that stops keyless lock operations when the power source mode is on, a door is open, or the vehicle is being driven, and performs keyless lock, power back door close and unlock, and hands free power back door operations.


Certification ECU (smart key ECU assembly)
·

Telephone transceiver assembly

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Multiplex network door ECU


Nothing Nothing
·

U014087

·

U015587

·

U020187

·

U020287

·

U023087

·

U111787


(Certification ECU (smart key ECU assembly))
Back Door Open Function
·

System that performs keyless luggage compartment unlock and hands free power back door operations.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU


Nothing Nothing
·

U014087

·

U023087


(Certification ECU (smart key ECU assembly))
Cabin Interior Lock Out Prevention Function
·

System that prevents the key from being locked in the vehicle.


Certification ECU (smart key ECU assembly) Main body ECU (multiplex network body ECU) Nothing Nothing U014087
(Certification ECU (smart key ECU assembly))
Back door lock out prevention function
·

System that prevents the key from being locked in the luggage compartment.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU


Nothing Nothing
·

U014087

·

U023087


(Certification ECU (smart key ECU assembly))
Entry and Start System Alarm / Operation Advice Display Function
·

System that performs the transmitter battery charge low alarm, emergency operation display, engine start operation notification, passenger exiting vehicle with key warning, vehicle start attempt with no key warning, engine start possible notification, mislaid key warning, and key confinement in luggage compartment warning.


Certification ECU (smart key ECU assembly) Combination meter assembly Nothing Nothing U015587
(Certification ECU (smart key ECU assembly))
Immobilizer F
·

System that performs immobilizer control and remote engine start.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Stop and start ECU

·

ECM


Nothing Nothing
·

U010087

·

U014087

·

U110387

·

U111787


(Certification ECU (smart key ECU assembly))
Steering Function
·

System that performs steering lock and unlock operations.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Nothing Nothing
·

U012987

·

U014087


(Certification ECU (smart key ECU assembly))
Engine switch backlight function
·

System that illuminates and turns off the engine switch backlight illumination based on the illumination state of the interior lights (dome light, etc.), door open/closed state, etc.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly


Nothing Nothing
·

U014087

·

U015587

·

U111787


(Certification ECU (smart key ECU assembly))
Memory function
·

System that remotely memorizes / recalls


Certification ECU (smart key ECU assembly) Main body ECU (multiplex network body ECU) Nothing Nothing U014087
(Certification ECU (smart key ECU assembly))
Key Registration Function
·

System that registers new keys / adds a key / deletes a key / deletes all keys, and registers the ECU code.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Telephone transceiver assembly


Nothing Nothing
·

U014087

·

U015587

·

U111787


(Certification ECU (smart key ECU assembly))
Wireless remote control function
·

System that performs remote vehicle operations such as lock/unlock.


Certification ECU (smart key ECU assembly)
·

Main body ECU (multiplex network body ECU)

·

Telephone transceiver assembly


Nothing Nothing
·

U014087

·

U111787


(Certification ECU (smart key ECU assembly))
Headlight Illumination Control Main body ECU (multiplex network body ECU)
·

ECM

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH


Nothing
·

Nothing

·

Displayed on multi-information display.


·

U010087

·

U014087

·

U024187

·

U024287

·

U114F87


(Main body ECU (multiplex network body ECU))
Cornering Light Control Headlight ECU sub-assembly LH
·

Main body ECU (multiplex network body ECU)

·

ECM

·

TCM

·

Headlight ECU sub-assembly RH

·

Steering sensor

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Cornering light control is stopped. Nothing
·

U010087

·

U010187

·

U012987

·

U014087

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
Headlight Cleaner Control Headlight ECU sub-assembly RH
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Steering sensor

·

Headlight ECU sub-assembly LH


Headlight cleaner control is stopped. Displayed on multi-information display.
·

U010087

·

U012687

·

U014087

·

U024187

·

U024287


(Headlight ECU sub-assembly RH)
Static Leveling Control Headlight ECU sub-assembly LH
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Headlight ECU sub-assembly RH

·

Combination meter assembly

·

Absorber control ECU

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Static leveling control is stopped. Displayed on multi-information display.
·

U010087

·

U012987

·

U013287

·

U014087

·

U015587

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
Dynamic Leveling Control Headlight ECU sub-assembly LH
·

Main body ECU (multiplex network body ECU)

·

ECM

·

Headlight ECU sub-assembly RH

·

Combination meter assembly

·

Absorber control ECU

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Performs dynamic leveling control as if the vehicle speed is 0 km/h (0 mph). Displayed on multi-information display.
·

U010087

·

U012987

·

U013287

·

U014087

·

U015587

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
AFS Control Headlight ECU sub-assembly LH
·

DRS

·

Main body ECU (multiplex network body ECU)

·

TCM

·

ECM

·

Headlight ECU sub-assembly RH

·

Combination meter assembly

·

Absorber control ECU

·

Steering sensor

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


AFS control is stopped. Displayed on multi-information display.
·

U010087

·

U010187

·

U012687

·

U012987

·

U013287

·

U014087

·

U015587

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
AHS Control Headlight ECU sub-assembly LH
·

DRS

·

Main body ECU (multiplex network body ECU)

·

TCM

·

ECM

·

Headlight ECU sub-assembly RH

·

Combination meter assembly

·

Absorber control ECU

·

Steering sensor

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


AHS control is stopped. Displayed on multi-information display.
·

U010087

·

U010187

·

U012687

·

U012987

·

U013287

·

U014087

·

U015587

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
Multi Weather Light Control Headlight ECU sub-assembly LH
·

Main body ECU (multiplex network body ECU)

·

TCM

·

ECM

·

Headlight ECU sub-assembly RH

·

Combination meter assembly

·

Absorber control ECU

·

Steering sensor

·

Brake booster with master cylinder assembly (No. 1 skid control ECU)


Multi weather light control is stopped. Displayed on multi-information display.
·

U010087

·

U010187

·

U012687

·

U012987

·

U013287

·

U014087

·

U015587

·

U024187

·

U024287


(Headlight ECU sub-assembly LH)
Seat Memory/Recall Function
·

Memorizes the position of the seat when the switch on the door is operated.

·

Also, moves each movable part of the seat to the memorized position.


Position control ECU assembly
·

Main body ECU (multiplex network body ECU)

·

Multiplex tilt and telescopic ECU


Operation of each movable part is stopped. Nothing
·

U114F87

·

U019987

·

U020087

·

U111587


(Position control ECU assembly)
Memory Call Recall Function
·

Automatically moves the driver seat to the key-linked driving position when the driver door is opened with the electrical key transmitter sub-assembly.


Position control ECU assembly
·

Main body ECU (multiplex network body ECU)

·

Multiplex tilt and telescopic ECU


Operation of each movable part is stopped. Nothing
·

U114F87

·

U111587


(Position control ECU assembly)
Auto Away/Return Function (Power Easy Access System)
·

Automatically slides the seat to improve accessibility when the seatbelt is fastened/unfastened and the ignition switch is turned ON/OFF.

·

Automatically operates support components for movable parts to facilitate entry and exit of the vehicle and to restore posture.


Position control ECU assembly Main body ECU (multiplex network body ECU) Operation of each movable part is stopped. Nothing U014087
(Position control ECU assembly)
Lift Up Buckle (Easy Access Buckle)
·

Moves the seatbelt buckle (easy access buckle) up and down to facilitate seatbelt fastening when entering the vehicle.


Position control ECU assembly Main body ECU (multiplex network body ECU) Nothing Nothing
·

U114F87

·

U019987

·

U020087


(Position control ECU assembly)
Pressure Adjustment Function
·

Adjusts and holds the pressure of the bladder at a set value when the temperature, pressure, or posture of the bladder is adjusted.


Position control ECU assembly Main body ECU (multiplex network body ECU) Pressure adjustment is stopped. Nothing U114F87
(Position control ECU assembly)
Full Discharge Function
·

When the customized value of auto away/return (power easy access) is OFF, releases air from the support components to protect the bladder when the vehicle is parked, etc. for a long period of time


Position control ECU assembly Main body ECU (multiplex network body ECU) Nothing Nothing U114F87
(Position control ECU assembly)
Full Charge Function
·

When the customized value of auto away/return (power easy access) is OFF, adds air to the support components to restore them to their previous state.


Position control ECU assembly Main body ECU (multiplex network body ECU) Nothing Nothing U114F87
(Position control ECU assembly)
Welcome Function
·

Deploys the cushion side support when entering or exiting the vehicle.


Position control ECU assembly Main body ECU (multiplex network body ECU) Nothing Nothing U114F87
(Position control ECU assembly)
Buckle Illumination Function
·

Illuminates and turns off the LED of the seatbelt buckle when fastening or unfastening the seatbelt to make it easier to find the seatbelt buckle.


Position control ECU assembly Main body ECU (multiplex network body ECU) Operation is stopped. Nothing U114F87
(Position control ECU assembly)
Refresh Function
·

Expands and contracts the bladder to help refresh the mind and body of the user when the switch is pressed.


Position control ECU assembly
·

Main body ECU (multiplex network body ECU)

·

Radio and display receiver assembly

·

Radio receiver assembly


Nothing Nothing U114F87
(Position control ECU assembly)
Auto-away Function
·

Moves the steering wheel to the most retracted position and tilts to the uppermost position when the system detects the driver side seat belt is unfastened and the ignition switch is turned off.


Multiplex tilt and telescopic ECU
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Position control ECU assembly

·

Radio and display receiver assembly

·

Radio receiver assembly


Control is stopped if an operation other than a manual switch operation is performed. Nothing
·

U014287

·

U015587


(Multiplex tilt and telescopic ECU)
Auto-return Function
·

Returns the steering wheel to the position before the auto-away operation was performed (the multiplex tilt and telescopic ECU memorized position) when the ignition switch is turned to ON or the driver side seat belt is fastened.


Multiplex tilt and telescopic ECU
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Position control ECU assembly

·

Radio and display receiver assembly

·

Radio receiver assembly


Control is stopped if an operation other than a manual switch operation is performed. Nothing
·

U014287

·

U015587


(Multiplex tilt and telescopic ECU)
Memorization and Recall Function
·

Memorizes or recalls the steering wheel position in accordance with the operation of the memory switch.


Multiplex tilt and telescopic ECU
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Position control ECU assembly

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Control is stopped if an operation other than the manual switch operation is performed.

·

Control is stopped if an operation other than the manual switch operation is performed


Nothing
·

U014287

·

U015587

·

U020887


(Multiplex tilt and telescopic ECU)
User Customize Function
·

Changes the behavior and control parameters of the auto-away and auto-return functions in accordance with the operation of the multi-media system.


Multiplex tilt and telescopic ECU
·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Position control ECU assembly

·

Radio and display receiver assembly

·

Radio receiver assembly


·

Each auto-operation function is stopped.

·

It is not possible to change the customize settings.


Nothing -