Home › General › SPECIFICATIONS › V35A-FTS ENGINE CONTROL
RM38G0E _V1 General _100727 SPECIFICATIONS _0479052 V35A-FTS ENGINE CONTROL F

SPECIFICATIONS  V35A-FTS ENGINE CONTROL  SERVICE DATA  


SPARK PLUG
Standard Insulation Resistance Spark plug (terminal part) - Body ground 10 MΩ or higher
Spark Plug Type DENSO made EC22HPR-D7
Maximum Electrode Gap for Used Spark Plug 0.9 mm (0.0354 in.)
Standard Electrode Gap for New Spark Plug 0.6 to 0.7 mm (0.0237 to 0.0275 in.)

CAMSHAFT OIL CONTROL VALVE (for Bank 1)
Standard Stroke (intake camshaft timing gear bolt assembly) 2.2 mm (0.0867 in.) or more
Standard Stroke (exhaust camshaft timing gear bolt assembly) 2.2 mm (0.0867 in.) or more

CAMSHAFT OIL CONTROL VALVE (for Bank 2)
Standard Stroke (intake camshaft timing gear bolt assembly) 2.2 mm (0.0867 in.) or more
Standard Stroke (exhaust camshaft timing gear bolt assembly) 2.2 mm (0.0867 in.) or more

CAMSHAFT OIL CONTROL SOLENOID (for Bank 1)
Standard Resistance (for Intake Side of Bank 1) C15-1 - C15-2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Standard Resistance (for Exhaust Side of Bank 1) C18-1 - C18-2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Stroke Amount (for Intake Side of Bank 1) Standard 4.3 mm (0.170 in.) or more
Stroke Amount (for Exhaust Side of Bank 1) Standard 4.3 mm (0.170 in.) or more

CAMSHAFT OIL CONTROL SOLENOID (for Bank 2)
Standard Resistance (for Intake Side of Bank 2) C16-1 - C16-2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Standard Resistance (for Exhaust Side of Bank 2) C19-1 - C19-2 0 °C (32 °F) 6.3 to 7.3 Ω
20 °C (68 °F) 6.9 to 7.9 Ω
40 °C (104 °F) 7.4 to 8.6 Ω
Stroke Amount (for Intake Side of Bank 2) Standard 4.3 mm (0.170 in.) or more
Stroke Amount (for Exhaust Side of Bank 2) Standard 4.3 mm (0.170 in.) or more

THROTTLE BODY
Standard Resistance C20-5 (M-) - C20-6 (M+) 25°C (77°F) 1.37 to 1.39 Ω

ACCELERATOR PEDAL
Accelerator Position Sensor No.1 Voltage Accelerator pedal fully released 0.5 to 1.1 V
Accelerator pedal fully depressed 2.6 to 4.5 V
Accelerator Position Sensor No.2 Voltage Accelerator pedal fully released 1.2 to 2.0 V
Accelerator pedal fully depressed 3.4 to 4.75 V

MASS AIR FLOW METER SUB-ASSEMBLY
Mass Air Flow Sensor Idling (engine warmed up) 1.8 to 3.0 gm/sec
2000 rpm (without load) 5.0 to 25.0 gm/sec
3000 rpm (without load) 6.5 to 30.0 gm/sec

ENGINE COOLANT TEMPERATURE SENSOR
Standard Resistance C28-1 (E2) - C28-2 (THW) 20°C (68°F) 2.31 to 2.58 kΩ
80°C (176°F) 0.310 to 0.326 kΩ

KNOCK CONTROL SENSOR
Standard Resistance C10-1 - C10-2 25°C (77°F) 120 to 280 kΩ
C9-1 - C9-2 25°C (77°F) 120 to 280 kΩ

KNOCK CONTROL SENSOR
Standard Resistance (for Bank 1) C10-1 - C10-2 25°C (77°F) 120 to 280 kΩ
Standard Resistance (for Bank 2) C9-1 - C9-2 25°C (77°F) 120 to 280 kΩ

MANIFOLD ABSOLUTE PRESSURE SENSOR
Standard Resistance C40-4 (THIM) - C40-2 (E2) -20 °C (-4 °F) 13.8 to 18.6 kΩ
20 °C (68 °F) 2.09 to 2.81 kΩ
80 °C (176 °F) 0.274 to 0.37 kΩ

AIR FUEL RATIO SENSOR
Standard Resistance (air fuel ratio sensor) C30-1 (HA2A) - C30-2 (+B) 20°C (68°F) 1.4 to 3.0 Ω
C30-3 (A2A+) - C30-4 (A2A-) Always 10 kΩ or higher
Standard Resistance (No. 2 air fuel ratio sensor) C29-1 (HA1A) - C29-2 (+B) 20°C (68°F) 1.4 to 3.0 Ω
C29-3 (A1A+) - C29-4 (A1A-) Always 10 kΩ or higher
Standard Resistance (No. 3 air fuel ratio sensor.) C32-1 (HA2B) - C32-2 (+B) 20°C (68°F) 2 to 6 Ω
C32-3 (A2B+) - C32-4 (A2B-) Always 10 kΩ or higher
Standard Resistance (No. 4 air fuel ratio sensor.) C31-1 (HA1B) - C31-2 (+B) 20°C (68°F) 2 to 6 Ω
C31-3 (A1B+) - C31-4 (A1B-) Always 10 kΩ or higher

NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 1)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 2)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 3)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

ELECTRONIC DRIVER UNIT RELAY (EDU)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

INSPECT INJECTOR RELAY (IGT/INJ)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

INSPECT IGP RELAY (IGP NO.1)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

INSPECT IGP RELAY NO.2 (IGP NO.2)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω

INSPECT IGR RELAY (IGR NO.3)
Standard Resistance 3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω