Home › General › SPECIFICATIONS › AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE › from 2021.07
RM38G0E _V1 General _100727 SPECIFICATIONS _0476882 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE F

SPECIFICATIONS  AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  SERVICE DATA  


AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
Line pressure D 1800 to 2100 kPa (18.4 to 21.4 kgf/cm2, 261 to 304 psi)
R 1800 to 2100 kPa (18.4 to 21.4 kgf/cm2, 261 to 304 psi)
Engine stall speed D 2205 to 2605 rpm
Time lag N → D position Less than 1.8 seconds
N → R position Less than 1.8 seconds

AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)
Line pressure D 1800 to 2100 kPa (18.4 to 21.4 kgf/cm2, 261 to 304 psi)
R 1800 to 2100 kPa (18.4 to 21.4 kgf/cm2, 261 to 304 psi)
Engine stall speed D 2550 to 2950 rpm
Time lag N → D position Less than 1.2 seconds
N → R position Less than 1.2 seconds

AUTOMATIC TRANSMISSION FLUID
Engine Type Capacity (Reference) Classification

*: Using transmission fluid other than the above type may cause abnormal noise or vibration, or damage the transmission of your vehicle.

Removal and installation of the automatic transmission oil pan sub-assembly and drain plug V35A-FTS 5.9 liters (6.2 US qts, 5.2 Imp. qts) Toyota Genuine ATF WS*
F33A-FTV 5.9 liters (6.2 US qts, 5.2 Imp. qts)
Removal and installation of the transmission valve body assembly V35A-FTS 6.5 liters (6.9 US qts, 5.7 Imp. qts)
F33A-FTV 6.5 liters (6.9 US qts, 5.7 Imp. qts)
Removal and installation of the torque converter assembly V35A-FTS 8.3 liters (8.8 US qts, 7.3 Imp. qts)
F33A-FTV 9.5 liters (10.0 USqts, 8.4 Imp. qts)

TRANSMISSION WIRE
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

C33-1 (OT1+) - Body ground Always 10 kΩ or higher
C33-2 (OT1-) - Body ground Always 10 kΩ or higher
C33-3 (OT2+) - Body ground Always 10 kΩ or higher
C33-4 (OT2-) - Body ground Always 10 kΩ or higher
C33-1 (OT1+) - C33-2 (OT1-) 10°C (50°F) 5 to 8 kΩ
C33-3 (OT2+) - C33-4 (OT2-) 10°C (50°F) 5 to 8 kΩ
C33-1 (OT1+) - C33-2 (OT1-) 25°C (77°F) 2.5 to 4.5 kΩ
C33-3 (OT2+) - C33-4 (OT2-) 25°C (77°F) 2.5 to 4.5 kΩ
C33-1 (OT1+) - C33-2 (OT1-) 110°C (230°F) 0.22 to 0.28 kΩ
C33-3 (OT2+) - C33-4 (OT2-) 110°C (230°F) 0.22 to 0.28 kΩ

VALVE BODY ASSEMBLY
Item Tester Connection Condition Specified Condition
Solenoid (SL1) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL2) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL3) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL4) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL5) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL6) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SLT) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SLU) valve 1 - 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SC1) valve Solenoid (SC1) valve connector terminal - Solenoid (SC1) valve body 20°C (68°F) 11 to 15 Ω
Solenoid (SR) valve Solenoid (SR) valve connector terminal - Solenoid (SR) valve body 20°C (68°F) 11 to 15 Ω
Solenoid (SL) valve Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω

PARK / NEUTRAL POSITION SWITCH
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-4 (B) - C34-5 (L) Shift lever in P or N Below 1 Ω
C34-4 (B) - C34-5 (L) Shift lever not in P or N 10 kΩ or higher
C34-2 (RB) - C34-6 (PL) Shift lever in P Below 1 Ω
C34-2 (RB) - C34-6 (PL) Shift lever not in P 10 kΩ or higher
C34-2 (RB) - C34-1 (RL) Shift lever in R Below 1 Ω
C34-2 (RB) - C34-1 (RL) Shift lever not in R 10 kΩ or higher
C34-2 (RB) - C34-9 (NL) Shift lever in N Below 1 Ω
C34-2 (RB) - C34-9 (NL) Shift lever not in N 10 kΩ or higher
C34-2 (RB) - C34-7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
C34-2 (RB) - C34-7 (DL) Shift lever not in D, M, "+" or "-" 10 kΩ or higher

SHIFT LEVER (SHIFT LOCK CONTROL ECU)
Tester Connection Condition Specified Condition

Click Location & Routing(I35)Location & Routing

Click Connector(I35)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Shift Lock Control Unit Assembly

I35-5 (STP) - Body ground Brake pedal depressed 11 to 14 V
I35-5 (STP) - Body ground Brake pedal released Below 1 V
I35-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I35-4 (IG) - Body ground Ignition switch off Below 1 V
I35-2 (E) - Body ground Always Below 1 Ω

SHIFT LEVER (TRANSMISSION CONTROL SWITCH (for LHD))
Tester Connection Condition Specified Condition

Click Location & Routing(I73)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I73-4 (IG) - I73-5 (S) Shift lever in M, "+" or "-" Below 1 Ω
I73-4 (IG) - I73-5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
I73-3 (SFTU) - I73-5 (M) Shift lever held in "+" (Up-shift) Below 1 Ω
I73-3 (SFTU) - I73-5 (M) Shift lever not held in "+" (Up-shift) 10 kΩ or higher
I73-1 (SFTD) - I73-2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
I73-1 (SFTD) - I73-2 (E) Shift lever not held in "-" (Down-shift) 10 kΩ or higher

SHIFT LEVER (TRANSMISSION CONTROL SWITCH (for RHD))
Tester Connection Condition Specified Condition

Click Location & Routing(I74)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

I74-4 (IG) - I74-5 (M) Shift lever in M, "+" or "-" Below 1 Ω
I74-4 (IG) - I74-5 (M) Shift lever not in M, "+" or "-" 10 kΩ or higher
I74-1 (SFTU) - I74-2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
I74-1 (SFTU) - I74-2 (E) Shift lever not held in "+" (Up-shift) 10 kΩ or higher
I74-3 (SFTD) - I74-2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
I74-3 (SFTD) - I74-2 (E) Shift lever not held in "-" (Down-shift) 10 kΩ or higher

COMBINATION SWITCH
Item Tester Connection Condition Specified Condition
Drive mode switch I88-5 (PSW2) - I88-8 (E) Drive mode switch being pushed and held 138 Ω or less
I88-5 (PSW2) - I88-8 (E) Drive mode switch not pushed 10 kΩ or higher
2nd start switch I88-13 (2ND) - I88-8 (E) 2nd start switch being pushed and held 66 Ω or less
I88-13 (2ND) - I88-8 (E) 2nd start switch not pushed 10 kΩ or higher

AUTOMATIC TRANSMISSION REAR OIL SEAL
Transmission case oil seal Installation Depth Standard 3.2 to 3.8 mm (0.126 to 0.150 in.)

AUTOMATIC TRANSMISSION UNIT
Stator shaft assembly Inside diameter Standard 25.900 to 25.926 mm (1.0197 to 1.0207 in.)
Brake piston return spring sub-assembly (No. 1 brake) Free length Standard 15.16 mm (0.597 in.)
No. 1 brake flange Inspect the piston stroke Standard clearance 0.749 to 1.331 mm (0.0295 to 0.0524 in.)
Adjust the piston stroke Standard clearance 0.800 to 1.000 mm (0.0315 to 0.0393 in.)
No. 1 brake flange thickness 35676-60260 Mark 0 5.45 to 5.55 mm (0.215 to 0.218 in.)
35676-60270 Mark 1 5.55 to 5.65 mm (0.219 to 0.222 in.)
35676-60280 Mark 2 5.65 to 5.75 mm (0.223 to 0.226 in.)
35676-60290 Mark 3 5.75 to 5.85 mm (0.227 to 0.230 in.)
35676-60300 Mark 4 5.85 to 5.95 mm (0.231 to 0.234 in.)
35676-60310 Mark 5 5.95 to 6.05 mm (0.235 to 0.238 in.)
35676-60320 Mark 6 6.05 to 6.15 mm (0.239 to 0.242 in.)
Front planetary sun gear sub-assembly Inside diameter Standard 37.000 to 37.015 mm (1.4567 to 1.4572 in.)
Front planetary gear assembly Inside diameter Standard 0.20 to 0.60 mm (0.00788 to 0.0236 in.)
C-2 clutch assembly Inspect the piston stroke Standard clearance 0.962 to 1.758 mm (0.0379 to 0.0692 in.)
C-1 clutch assembly Inspect the piston stroke Standard clearance 1.220 to 2.060 mm (0.0481 to 0.0811 in.)
Inside diameter (Front side) Standard 49.989 to 50.014 mm (1.9681 to 1.9690 in.)
Inside diameter (Rear side) Standard 44.480 to 44.505 mm (1.7512 to 1.7521 in.)
Brake piston return spring sub-assembly (No. 2 Free length Standard 18.11 mm (0.713 in.)
No. 2 brake flange Inspect the piston stroke Standard clearance 0.605 to 1.395 mm (0.0239 to 0.0549 in.)
Adjust the piston stroke Standard clearance 0.900 to 1.100 mm (0.0355 to 0.0433 in.)
No. 1 brake flange thickness 35678-60300 Mark 0 6.78 to 6.85 mm (0.267 to 0.269 in.)
35678-60310 Mark 1 6.85 to 6.95 mm (0.270 to 0.273 in.)
35678-60320 Mark 2 6.95 to 7.05 mm (0.274 to 0.277 in.)
35678-60330 Mark 3 7.05 to 7.15 mm (0.278 to 0.281 in.)
35678-60340 Mark 4 7.15 to 7.25 mm (0.282 to 0.285 in.)
35678-60350 Mark 5 7.25 to 7.35 mm (0.286 to 0.289 in.)
35678-60360 Mark 6 7.35 to 7.45 mm (0.290 to 0.293 in.)
35678-60370 Mark 7 7.45 to 7.55 mm (0.294 to 0.297 in.)
35678-60380 Mark 8 7.55 to 7.65 mm (0.298 to 0.301 in.)
No. 3 clutch Inspect the piston stroke Standard 0.772 to 1.628 mm (0.0304 to 0.0640 in.)
Center support assembly Inside diameter Standard 73.082 to 73.121 mm (2.8773 to 2.8787 in.)
Center Planetary Gear Assembly Clearance Standard 0.20 to 0.67 mm (0.00788 to 0.02637 in.)
Planetary sun gear sub-assembly Inside diameter Standard 30.600 to 30.621 mm (1.2048 to 1.2055 in.)
Rear planetary gear assembly Clearance Standard 0.20 to 0.64 mm (0.00788 to 0.02519 in.)
forward clutch return spring sub-assembly (C-4 clutch) Free length Standard 21.41 mm (0.843 in.)
No. 4 clutch Inspect the piston stroke Standard Clearance 0.571 to 1.429 mm (0.0225 to 0.0562 in.)
Adjust the piston stroke Standard Clearance 0.900 to 1.100 mm (0.0355 to 0.0433 in.)
Clutch flange thickness 35635-60510 4.25 to 4.35 mm (0.168 to 0.171 in.)
35635-60520 4.35 to 4.45 mm (0.172 to 0.175 in.)
35635-60530 4.45 to 4.55 mm (0.176 to 0.179 in.)
35635-60540 4.55 to 4.65 mm (0.180 to 0.183 in.)
35635-60550 4.65 to 4.75 mm (0.184 to 0.187 in.)
35635-60560 4.75 to 4.85 mm (0.188 to 0.190 in.)
35635-60570 4.85 to 4.95 mm (0.191 to 0.194 in.)
35635-60580 4.95 to 5.05 mm (0.195 to 0.198 in.)
35635-60590 5.05 to 5.15 mm (0.199 to 0.202 in.)
Automatic transmission case sub-assembly Free length Standard 48.370 to 48.455 mm (1.9044 to 1.9076 in.)
Front planetary gear assembly and front planetary ring gear Clearance Standard 15.7 to 17.6 mm (0.619 to 0.692 in.)
Stator shaft assembly Clearance Standard 1.02 to 1.85 mm (0.0402 to 0.0728 in.)
Input shaft End play Standard 0.47 to 1.31 mm (0.0186 to 0.0515 in.)

TORQUE CONVERTER AND DRIVE PLATE
Drive plate and ring gear sub-assembly (for Gasoline) Runout Maximum 0.30 mm (0.0118 in.)
Pump impeller drive plate (for Diesel) Runout Maximum 0.30 mm (0.0118 in.)

OIL PUMP
Oil pump assembly Clearance Standard 0.135 to 0.185 mm (0.00532 to 0.00728 in.)
Tip Clearance Standard 0.02 to 0.10 mm (0.000788 to 0.00393 in.)
Side Clearance Standard 0.017 to 0.030 mm (0.000670 to 0.00118 in.)
Front oil pump drive gear thickness 35321-60210 13.635 to 13.640 mm (0.53682 to 0.53700 in.)
35321-60220 13.638 to 13.643 mm (0.53693 to 0.53712 in.)
35321-60230 13.641 to 13.646 mm (0.53705 to 0.53724 in.)
Front oil pump driven gear thickness 35322-60210 13.635 to 13.640 mm (0.53682 to 0.53700 in.)
35322-60220 13.638 to 13.643 mm (0.53693 to 0.53712 in.)
35322-60230 13.641 to 13.646 mm (0.53705 to 0.53724 in.)