Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for F33A-FTV) › from 2021.07
RM38G0E _58 Vehicle Interior _100766 HEATING / AIR CONDITIONING _0484758 COMPRESSOR(for F33A-FTV) G

HEATING / AIR CONDITIONING  COMPRESSOR(for F33A-FTV)  INSPECTION  


PROCEDURE

Hide 88410 1.INSPECT MAGNET CLUTCH ASSEMBLY

a.

Inspect the magnet clutch assembly.

i.
E468031C05
1.51,0.406 1.917,0.594 0.406,0.188 2.333,1.833 2.083,1.292 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.25,1.854 2.865,2.052 0.615,0.198 10 false MG+ 1.594,0.417 2.052,0.615 0.458,0.198 10 false C39
*a Component without harness connected
(Compressor with Magnet Clutch)


Apply battery voltage to the clutch and check the operation of the clutch.

OK:
Tester Connection Specified Condition

Click Location & Routing(C39)Location & Routing

Click Connector(C39)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Compressor with Magnet Clutch Assembly

Battery positive (+) → C39-1 (MG+)
Battery negative (-) → Body ground
Magnet clutch is engaged


If the value is not within the standard, perform the following inspections.


ii.
E468093C03
0.51,0.417 0.854,0.417 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.896,0.323 1.052,0.521 0.156,0.198 10 false 1
*a Component without harness connected
(Magnet Clutch Assembly)


Disconnect the wire harness of the compressor with magnet clutch and check that the magnet clutch assembly operates when battery voltage is applied to the connector terminal on the magnet clutch side.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Body ground
Magnet clutch is engaged


·

If the result is not as specified, replace the magnet clutch assembly.

·

If the magnet clutch assembly is normal, replace the cooler compressor assembly.




b.

Inspect the Temperature fuse.

i.
E468031C05
1.51,0.406 1.917,0.594 0.406,0.188 2.333,1.833 2.083,1.292 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.25,1.854 2.865,2.052 0.615,0.198 10 false MG+ 1.594,0.417 2.052,0.615 0.458,0.198 10 false C39
*a Component without harness connected
(Compressor with Magnet Clutch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C39)Location & Routing

Click Connector(C39)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Compressor with Magnet Clutch Assembly

C39-1 (MG+) - Body ground 20°C (68°F) 2.8 to 3.2 Ω


If the value is not within the standard, perform the following inspections.


ii.
E468093C03
0.51,0.417 0.854,0.417 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.896,0.323 1.052,0.521 0.156,0.198 10 false 1
*a Component without harness connected
(Magnet Clutch Assembly)


Disconnect the wire harness of the compressor with magnet clutch and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground 20°C (68°F) 2.8 to 3.2 Ω


·

If the result is not as specified, replace the magnet clutch assembly.

·

If the magnet clutch assembly is normal, replace the cooler compressor assembly.