Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P023A71  Charge Air Cooler Coolant Pump Control Actuator Stuck  P2B8300  Charge Air Cooler Coolant Pump Overspeed/Air In System  


DESCRIPTION

Refer to DTC P023A12.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P023A12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023A71 Charge Air Cooler Coolant Pump Control Actuator Stuck The rotational speed of the pump is less than the lower limit value for 75 seconds or more while the electric water pump assembly is operating.
(2 trip detection logic)
Electric water pump assembly Comes on SAE Code: P2BC1
P2B8300 Charge Air Cooler Coolant Pump Overspeed/Air In System The rotational speed of the pump is higher than the upper limit value for 75 seconds or more while the electric water pump assembly is operating.
(2 trip detection logic)
·

Insufficient coolant (for intercooler)

·

Coolant leak (for intercooler)

·

Electric water pump assembly

·

Electric water pump assembly


Comes on SAE Code: P2B83

MONITOR DESCRIPTION

The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.

A 4 Hz duty signal (IWPI) is output even when the pump is stopped. The ECM then converts the electric water pump assembly rotational duty signal (IWPI) into the rotational speed and checks that it is 160 rpm when the pump is stopped.

If the actual speed exceeds the target speed by a fixed value or more, the ECM evaluates overspeed operation. If the actual speed is below the target speed by a fixed value or more, the ECM evaluates that the motor is stuck. In these cases it stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P023A71
P2B8300
After fully warming up, drive the vehicle at approximately 50 km/h for 10 minutes or more.

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

P2B8300 may be detected if operation continues when the coolant (for intercooler) is insufficient. If there is sufficient coolant (for intercooler) and P2B8300 is output when the vehicle is brought to the workshop, check if the customer has added extra coolant to the intercooler in the past.

·

If the electric water pump assembly voltage is high or low, control may be temporarily stopped and P023A71 output. When the high- or low-voltage status situation is resolved, the temporarily halted control returns to normal. Therefore, it is not necessary to replace the electric water pump assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P023A71 OR P2B8300)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P023A71 or P2B8300 is output A
DTC P023A71 or P2B8300 and other DTCs are output B


HINT:

If any DTCs other than P023A71 or P2B8300 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Turn the ignition switch to ON.

NOTICE:

Be sure to perform the inspection with the battery voltage at 11 V or more.


HINT:

If the battery voltage is low, the electric water pump assembly may stop operating.



b.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump / Data List / Intercooler Water Pump Speed.

Powertrain > Engine > Active Test
Active Test Display
Control the Intercooler Water Pump
Data List Display
Intercooler Water Pump Speed
50004 372 9 104

c.

Read the Data List during 85% drive of the electric water pump.

Result:
GTS Operation Intercooler Water Pump Speed Proceed to
85% 4000 rpm or less A
7000 rpm or more B
Other than above C


HINT:
·

If the electric water pump assembly voltage is high or low, control may be temporarily stopped and a DTC stored.

·

Freezing occurs at -15°C at 30% coolant concentration and at -35°C at 50% coolant concentration.

·

DTC P023A71 is stored if the electric water pump assembly cannot rotate due to freezing.

·

If DTC P023A71 is stored due to freezing of the coolant, the problem cannot be reproduced. Judge whether freezing of the coolant occurred from the coolant replacement history and the ambient temperature when the DTC was stored.





A

3.REPLACE ELECTRIC WATER PUMP ASSEMBLY

B

4.CHECK COOLANT LEVEL AT RESERVOIR

C

3.REPLACE ELECTRIC WATER PUMP ASSEMBLY
a.

Replace the electric water pump assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>WATER PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
4.CHECK COOLANT LEVEL AT RESERVOIR
a.

Check the coolant (for intercooler) quantity.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>COOLANT>ON-VEHICLE INSPECTION


Result:
Result Proceed to
At or below reservoir tank LOW level. A
At or above reservoir tank LOW level. B



A

5.CHECK FOR COOLANT LEAK

B

7.BLEED AIR
5.CHECK FOR COOLANT LEAK
a.

Check the turbocharger, intercooler cooling system, exhaust fuel addition injector assembly and urea injector assembly(w/ Urea SCR System) for coolant leaks.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>COOLANT>ON-VEHICLE INSPECTION

OK:

No leaks.



Result:
Proceed to
OK
NG



OK

7.BLEED AIR

NG

6.REPAIR COOLANT LEAK
6.REPAIR COOLANT LEAK
a.

Repair any coolant leaks.


Result:
Proceed to
NEXT



NEXT

7.BLEED AIR
7.BLEED AIR
a.

Bleed the air and add coolant up to the FULL Line on the reservoir tank.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>COOLANT>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Turn the ignition switch to ON.

NOTICE:

Be sure to perform the inspection with the battery voltage at 11 V or more.


HINT:

If the battery voltage is low, the electric water pump assembly may stop operating.



b.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump / Data List / Intercooler Water Pump Speed.

Powertrain > Engine > Active Test
Active Test Display
Control the Intercooler Water Pump
Data List Display
Intercooler Water Pump Speed
50004 372 9 104

c.

Read the Data List during 85% drive of the electric water pump.

Standard:

In the Data List, the Electric Water Pump Speed is 4000 to 7000 rpm.



Result:
Proceed to
NEXT



NEXT

END