Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) D

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER SUB-ASSEMBLY


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly, turbocharger sub-assembly or turbocharger nozzle vane control actuator is replaced, perform initialization


a.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.



CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION


HINT:

When the front exhaust pipe sub-assembly (DPF catalyst) is replaced, the catalyst deterioration learning value and DPF deposition value stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / Catalyst Deterioration Leaning Value Clear.

Powertrain > Engine > Utility
Tester Display
Catalyst Deterioration Learning Value Clear
50005 372 4568

d.

Press "Next".


e.

Press "Exit".


f.

Enter the following menus: Powertrain / Engine / Utility / DPF Deposition Value Clear.

Powertrain > Engine > Utility
Tester Display
DPF Deposition Value Clear
50005 372 4574

g.

Press "Next".


h.

Press "Exit".



A/F SENSOR LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Learning Value Clear".

·

When replacing the air fuel ratio sensor (w/o Urea SCR System), replace the sensor and then perform "A/F Sensor Learning Value Clear".

·

When replacing the No. 1 nitrogen oxides sensor (w/ Urea SCR System), replace the sensor and then perform "A/F Sensor Learning Value Clear".

HINT:

The No. 1 nitrogen oxides sensor has an air fuel ratio sensor function. Therefore, perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.



HINT:
·

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / A/F Sensor Learning Value Clear.

Powertrain > Engine > Utility
Tester Display
A/F Sensor Learning Value Clear
50005 372 4572

d.

When the first screen is displayed, check the vehicle condition and press "Next".


e.

When the screen indicating reset completion is displayed, press "Exit".



i-ART Learning Value Reset


NOTICE:
·

When the engine is started after the i-ART learned value is reset with the ignition switch ON, the value for "Injection Feedback Value" may indicate a malfunction momentarily. However, this is not a malfunction and is due to the i-ART learned value being reset. The value returns to normal once learning is begun.

·

When the battery cable is disconnected, reconnect the battery cable, turn the ignition switch to ON and wait 3 minutes or more before performing this procedure.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / i-ART Learning Value Reset.

Powertrain > Engine > Utility
Tester Display
i-ART Learning Value Reset
50005 372 4610
·

3 minutes or more has elapsed after turning the ignition switch to ON and connecting the battery cable.

·

The engine is stopped.

·

The battery voltage is 8 V or more.



d.

Select the cylinder to be reset.


e.

Press "Next".

HINT:

The reset is performed automatically after "Next" is selected.



f.

If the reset fails, confirm the following conditions and perform the reset again.

i.

Turn the ignition switch to ON.


ii.

Turn the ignition switch off and wait for 30 seconds or more.


iii.

Turn the ignition switch to ON and wait 3 minutes or more.


iv.

The battery voltage is 8 V or more.



g.

When the screen indicating reset completion is displayed, push "Exit".



SWITCH SPECIFICATION INFORMATION


HINT:
·

Perform Switch Specification Information after replacing the ECM.

·

Perform Switch Specification Information using Utility of the GTS.

·

Perform the Health Check using the GTS and check that no DTC is output.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Switch Specification Information.

Powertrain > Engine > Utility
Tester Display
Switch Specification Information
50005 372 4551

e.

According to the prompts on the GTS screen, perform Switch Specification Information.


f.

Enter the following menus: Powertrain / Engine / Data List / Suspension Control Module Specification Information.

Powertrain > Engine > Data List
Tester Display
Suspension Control Module Specification Information
50003 372 1371

g.

Check that the Suspension Control Module Specification Information of the Data List displays a result other than Incomplete.

NOTICE:

If Incomplete is displayed, perform Switch Specification Information using Utility again.