DESCRIPTION
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.
3 data sets from before the DTC was stored
1 data set from when the DTC was stored
1 data set from after the DTC was stored
These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
LIST OF FREEZE FRAME DATA
| Tester Display |
|---|
| Total Distance Traveled |
| Total Distance Traveled - Unit |
| Vehicle Speed |
| Target Idle Engine Speed |
| Engine Speed |
| Calculate Load |
| Mass Air Flow Sensor |
| Atmospheric Pressure |
| Intake Manifold Absolute Pressure |
| Intake Manifold Absolute Pressure Supported |
| Coolant Temperature |
| Intake Air Temperature B1S1 (Turbo) |
| Intake Air Temperature B1S1 (Turbo) Supported |
| Intake Air Temperature B1S2 (Turbo) Supported |
| Intake Air Temperature B1S1 |
| Intake Air Temperature B1S2 |
| Intake Air Temperature B1S1 Supported |
| Intake Air Temperature B1S2 Supported |
| Intake Air Temperature B1S3 Supported |
| Intake Air Temperature B2S1 Supported |
| Intake Air Temperature B2S2 Supported |
| Intake Air Temperature B2S3 Supported |
| NOx Corrected Density B1S1 |
| NOx Corrected Density B1S2 |
| NOx Corrected Density B1S1 Supported |
| NOx Corrected Density B1S2 Supported |
| NOx Corrected Density B2S1 Supported |
| NOx Corrected Density B2S2 Supported |
| Ambient Temperature |
| Engine Run Time |
| IG-ON Coolant Temperature |
| Initial Engine Coolant Temperature |
| IG-ON Intake Air Temperature |
| Initial Engine Intake Air Temperature |
| Battery Voltage |
| BATT Voltage |
| Alternate Duty Ratio |
| IG2 / IGP |
| IGR |
| Glow Relay Request Bank 1 |
| Glow Relay Request Bank 2 |
| Glow Control Unit Duty |
| Glow Control Unit 2 Duty |
| Engine Oil Pressure |
| Accel Position |
| Accelerator Position Sensor No.1 Voltage % |
| Accelerator Position Sensor No.2 Voltage % |
| Actual Throttle Position Bank 1 |
| Target Throttle Position Bank 1 |
| Actual Throttle Position Bank 1 Supported |
| Actual Throttle Position Bank 2 Supported |
| Target Throttle Position Bank 1 Supported |
| Target Throttle Position Bank 2 Supported |
| Throttle Position Sensor No.1 Voltage % |
| Diesel Throttle Motor Duty Bank 1 |
| Diesel Throttle Target Angle Bank 1 |
| Throttle Close Learning Value Bank 1 |
| 1st Turbocharger/Supercharger Outlet Pressure (Control Value) |
| 2nd Turbocharger/Supercharger Outlet Pressure |
| 2nd Turbocharger/Supercharger Outlet Pressure (Control Value) |
| Neutral Control |
| N Range Status |
| Electric Duty Feedback Value |
| PS Duty Feedback Value |
| Total Injection Volume |
| Target Injection Volume |
| Injection Feedback Volume for Idle |
| Injection Volume Cylinder #1 |
| Injection Feedback Value #1 |
| Injection Feedback Value #2 |
| Injection Feedback Value #3 |
| Injection Feedback Value #4 |
| Injection Feedback Value #5 |
| Injection Feedback Value #6 |
| Injection Volume #1 |
| Injection Volume #2 |
| Injection Volume #3 |
| Injection Volume #4 |
| Injection Volume #5 |
| Injection Volume #6 |
| Pilot 1 Injection Period |
| Pilot 2 Injection Period |
| Pre Injection Period |
| Pilot 4 Injection Period |
| Main Injection Period |
| After Injection Period |
| After 2 Injection Period |
| After 3 Injection Period |
| After 4 Injection Period |
| Pre Post 1 Injection Period |
| Pre Post 2 Injection Period |
| Pilot 1 Injection Timing |
| Pilot 2 Injection Timing |
| Pre Injection Timing |
| Pilot 4 Injection Timing |
| Main Injection Timing |
| Main Injection Timing |
| After Injection Timing |
| After 2 Injection Timing |
| After 3 Injection Timing |
| After 4 Injection Timing |
| Pre Post 1 Injection Timing |
| i-ART Learning Status #1 |
| i-ART Learning Status #2 |
| i-ART Learning Status #3 |
| i-ART Learning Status #4 |
| i-ART Learning Status #5 |
| i-ART Learning Status #6 |
| i-ART Learning Status History #1 |
| i-ART Learning Status History #2 |
| i-ART Learning Status History #3 |
| i-ART Learning Status History #4 |
| i-ART Learning Status History #5 |
| i-ART Learning Status History #6 |
| Injector Leaking Count #1 |
| Injector Leaking Count #2 |
| Injector Leaking Count #3 |
| Injector Leaking Count #4 |
| Injector Leaking Count #5 |
| Injector Leaking Count #6 |
| Injection Pressure Correction |
| PCV Energization Timing |
| Target Fuel Pressure (High) |
| Target Fuel Pressure (High) Supported |
| Target Fuel Pressure (Low) / Target Fuel Pressure 2 |
| Target Fuel Pressure (Low) / Target Fuel Pressure 2 Supported |
| Fuel Pressure (High) |
| Fuel Pressure (High) Supported |
| Fuel Pressure (Low) / Fuel Pressure 2 |
| Fuel Pressure (Low) / Fuel Pressure 2 Supported |
| Fuel Pressure #1 |
| Fuel Pressure #2 |
| Fuel Pressure #3 |
| Fuel Pressure #4 |
| Fuel Pressure #5 |
| Fuel Pressure #6 |
| Fuel Temperature #1 |
| Fuel Temperature #2 |
| Fuel Temperature #3 |
| Fuel Temperature #4 |
| Fuel Temperature #5 |
| Fuel Temperature #6 |
| Fuel Return Temperature |
| Fuel Filter Heater Temperature |
| Fuel Filter Heater Temperature Sensor |
| Fuel Filter Heater Relay Output Terminal Status |
| Fuel Filter Heater Relay Diagnosis Result |
| Engine Fuel Rate |
| Vehicle Fuel Rate |
| Injection Control Malfunction (Target Injection Volume 1) |
| Injection Control Malfunction (Target Injection Volume 2) |
| Injection Control Malfunction (Target Injection Volume 3) |
| Injection Control Malfunction (Injector Current-Carrying Time 1) |
| Injection Control Malfunction (Injector Current-Carrying Time 2) |
| Injection Control Malfunction (Injector Current-Carrying Time 3) |
| Injection Control Malfunction (Fail Safe Function) |
| Pump Difference Angle Learning Value |
| Intank Fuel Pump |
| Current Fuel Type |
| A/F (O2) Lambda B1S1 |
| A/F (O2) Lambda B1S1 Supported |
| A/F (O2) Lambda B1S2 Supported |
| A/F (O2) Lambda B2S1 Supported |
| A/F (O2) Lambda B2S2 Supported |
| A/F (O2) Density B1S1 Supported |
| A/F (O2) Density B1S2 Supported |
| A/F (O2) Density B2S1 Supported |
| A/F (O2) Density B2S2 Supported |
| Intercooler Coolant Temperature |
| Intercooler Water Pump Speed |
| Intercooler Water Pump |
| Target EGR Valve Position No.1 |
| Target EGR Valve Position No.1 Supported |
| EGR Step Position Bank 1 |
| Actual EGR Valve Position No.1 |
| Actual EGR Valve Position No.1 Supported |
| EGR Rate Differential (Actual-Target) |
| Target EGR Valve Position No.2 Supported |
| Actual EGR Valve Position No.2 Supported |
| EGR Cooler Bypass Position |
| EGR Cooler Bypass Valve Request Position |
| EGR Cooler Bypass Valve Position |
| EGR Cooler Bypass Valve Position Sensor |
| EGR Cooler Bypass Valve Duty Ratio |
| EGR Cooler Bypass Valve Motor Current |
| EGR Cooler Bypass Valve Motor Overcurrent Detection Status |
| EGR Close Learning Value Bank 1 |
| EGR Position Sensor Bank 1 |
| EGR Temperature B1S1 |
| EGR Temperature B1S1 Wide Range Supported |
| Target Boost Pressure |
| Target Boost Pressure Supported |
| Target Boost Pressure2 Supported |
| Boost Pressure Sensor Supported |
| Boost Pressure Sensor2 Supported |
| Target VN Turbo Position Bank 1 |
| Actual VN Turbo Position Bank 1 |
| Target VN Turbo Position Bank 1 Supported |
| Actual VN Turbo Position Bank 1 Supported |
| Target VN Turbo Position Bank 2 Supported |
| Actual VN Turbo Position Bank 2 Supported |
| Target VN Turbo 2 Position |
| Actual VN Turbo 2 Position |
| VN Position Sensor Out Bank 1 |
| VN Turbo 2 Position Sensor Out |
| VN Close Learn Value Bank 1 |
| VN Turbo 2 Close Learn Value |
| VN Turbo Minimum Angle |
| VN Turbo Maximum Angle |
| VN Turbo 2 Maximum Angle |
| VN Turbo 2 Minimum Angle |
| Turbo Charger Step Motor Bank 1 |
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
| Exhaust Temperature B1S4 |
| Exhaust Temperature B1S1 Supported |
| Exhaust Temperature B1S2 Supported |
| Exhaust Temperature B1S3 Supported |
| Exhaust Temperature B1S4 Supported |
| Particulate Filter Differential Pressure Bank 1 |
| Particulate Filter Differential Pressure Bank 1 Supported |
| Catalyst Differential Pressure Bank 1 |
| Differential Pressure Sensor Correction Bank 1 |
| Catalyst Regeneration Switch |
| DPNR/DPF Status Regeneration (PM) |
| Exhaust Fuel Addition F/B Bank 1 |
| Exhaust Aftertreatment Fuel Injection Valve Current-Carrying Request |
| PM Accumulation Ratio Bank 1 |
| Starter SW |
| Neutral Position SW |
| Stop Light SW |
| Immobiliser Communication |
| Clogged Fuel Filter Switch |
| Cruise Main SW |
| TC Terminal |
| MIL ON Run Distance |
| Running Time from MIL ON |
| Time after DTC Cleared |
| Distance from DTC Cleared |
| Warmup Cycle Cleared DTC |
| Distance Traveled from Last Battery Cable Disconnect |
| IG OFF Elapsed Time |
| Soak IC Current Timer Value |
| Engine Speed (Starter Off) |
| Starter Count |
| Run Distance of Previous Trip |
| Engine Starting Time |
| IG ON Time |
| Glow Request Lighting Time |
| Engine Coolant Temperature High |
| Common Rail Pressure Low |
| Boost Pressure Low |
| MAF Low |
| MAF/Estimate MAF Ratio |
| Minimum Engine Speed |
| Compression Leakage Count |
| Plural Cylinders Rough Idle |
| Rough Idle Cylinder #1 |
| Rough Idle Cylinder #2 |
| Rough Idle Cylinder #3 |
| Rough Idle Cylinder #4 |
| Rough Idle Cylinder #5 |
| Rough Idle Cylinder #6 |
| Voltage of Alternator |
| Electronic Control Coupling Fan Speed |
| Brake Override System |
| Immobiliser Fuel Cut Status |
| Immobiliser Fuel Cut History |
| Engine Speed Cylinder #1 |
| Engine Speed Cylinder #2 |
| Engine Speed Cylinder #3 |
| Engine Speed Cylinder #4 |
| Engine Speed Cylinder #5 |
| Engine Speed Cylinder #6 |
| Average Engine Speed of All Cylinder |
| Output Axis Speed |
| Sport Shift Up SW |
| Sport Shift Down SW |
| Shift SW Status (S Range) |
| Snow Mode SW |
| A/T Oil Temperature No.1 |
| Drive Mode Status |
| Endless Rotary Switch (Phase A) |
| Endless Rotary Switch (Phase B) |
| Multi Terrain Select Mode Switching Switch |
| Drive Mode Select Switching Switch |
| Lock Up Status |
| Shift Status |
| Snow or 2nd Start Mode Status |
| Air Bypass Valve Current-Carrying Request |
| Air Control Valve Current-Carrying Request |
| Exhaust Control Valve Current-Carrying Request |
| Reductant Temperature |
| Reductant Pressure |
| Reductant Pump Speed |
| Reductant Injection Mode |
| Reductant Injection Value |
| Reductant Replenishment Possible Value |
| SCR Temperature |
| Reductant Injection Value Restraint Control |
| SCR NOx Purge High Efficiency Temperature |
| NOx Sensor Carrying Request |
| Fr-NOx Sensor Carrying Request |
| NOx Sensor Cooling Time |
| Fr-NOx Sensor Cooling Time |
| Engine Exhaust NOx Density |
| Catalyst Thermal Degradation Count |
| Reductant Injection Valve |
| Reductant Pipe Heater |
| Reductant Tank Heater |
| Reductant Discharge |
| Reductant Filling (Pressure Keep) |
| Reductant Pump Check (Backward) |
| Reductant Purge |
| SCR Caution Level |
| Status of Fr-NOx Sensor Lambda Detection Unit |
| Status of Fr-NOx Sensor NOx Detection Unit |
| Status of Fr-NOx Sensor |
| Status of Fr-NOx Sensor Heater |
| Fr-NOx Sensor NOx Active Status (SCU) |
| Fr-NOx Sensor A/F Active Status (SCU) |
| Fr-NOx Sensor Status Information |
| Status of Fr-NOx Sensor Power Supply Voltage |
| Status of NOx Sensor Lambda Detection Unit |
| Status of NOx Sensor NOx Detection Unit |
| Status of NOx Sensor |
| Status of NOx Sensor Heater |
| NOx Sensor NOx Active Status (SCU) |
| NOx Sensor A/F Active Status (SCU) |
| NOx Sensor Status Information |
| Status of NOx Sensor Power Supply Voltage |