FAIL-SAFE CHART
If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.
| DTC No. | Detection Item | Fail-safe Operation | Fail-safe Deactivation Condition |
|---|---|---|---|
| P003012 | HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery | A/F is fixed at a specified value. | Pass condition detected |
| P003013 | HO2S Heater Control Bank 1 Sensor 1 Circuit Open | A/F is fixed at a specified value. | Pass condition detected |
| P003314 | Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Ground or Open |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P004518 | Turbocharger/Supercharger Boost Control "A" Circuit Short to Battery |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P004519 | Turbocharger/Supercharger Boost Control "A" Circuit Short to Ground or Open |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P004600 | Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P004646 | Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance Calibration / Parameter Memory Failure | VN Turbo Offset Voltage Value is fixed at a specified value. | VN Turbo Offset Voltage Value Compensation performed |
| P006900 | Manifold Absolute Pressure - Barometric Pressure Correlation |
·
The atmospheric pressure is fixed at 60 kPa.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P007A11 | Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground |
·
The intake air temperature (for intercooler outlet) is fixed at 150°C.
·
The intercooler temperature feedback is stopped. |
Pass condition detected |
| P007A15 | Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open |
·
The intake air temperature (for intercooler outlet) is fixed at 150°C.
·
The intercooler temperature feedback is stopped. |
Pass condition detected |
| P008800 | Fuel Rail / System Pressure - Too High | Engine output is limited at 10%. | Ignition switch off |
| P009300 | Fuel System Leak Detected - Large Leak |
·
The engine power is limited.
·
PM forced regeneration is prohibited. |
Pass condition detected |
| P009511 | Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Ground | The intake air temperature (for intercooler inlet) is fixed at 200°C. | Pass condition detected |
| P009515 | Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open | The intake air temperature (for intercooler inlet) is fixed at 200°C. | Pass condition detected |
| P00DE11 | Charge Air Cooler Coolant Temperature Sensor Circuit Low Circuit Short to Ground |
·
The intercooler coolant temperature output is fixed at 120°C.
·
The target intake manifold absolute pressure is limited. |
Pass condition detected |
| P00DE15 | Charge Air Cooler Coolant Temperature Sensor Circuit High Circuit Short to Battery or Open |
·
The intercooler coolant temperature output is fixed at 120°C.
·
The target intake manifold absolute pressure is limited. |
Pass condition detected |
| P010012 | Mass or Volume Air Flow Sensor "A" Circuit Short to Battery |
·
All catalyst controls are stopped.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P010014 | Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open |
·
All catalyst controls are stopped.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P01009B | Mass or Volume Air Flow Sensor "A" High/Excessive Flow | The engine power is limited. | Ignition switch off |
| P01009C | Mass or Volume Air Flow Sensor "A" Low/Insufficient Flow | The engine power is limited. | Ignition switch off |
| P010512 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Battery |
·
The intake manifold absolute pressure is fixed at 101.3 kPa.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P010514 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Ground or Open |
·
The intake manifold absolute pressure is fixed at 101.3 kPa.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P010516 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Below Threshold |
·
The intake manifold absolute pressure is fixed at 101.3 kPa.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P010517 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Voltage Above Threshold |
·
The intake manifold absolute pressure is fixed at 101.3 kPa.
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P011011 | Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground |
·
The intake air temperature value is fixed at 60°C.
·
The target intake manifold absolute pressure is limited. |
Pass condition detected |
| P011015 | Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open |
·
The intake air temperature value is fixed at 60°C.
·
The target intake manifold absolute pressure is limited. |
Pass condition detected |
| P011511 | Engine Coolant Temperature Sensor 1 Circuit Short to Ground |
·
The target intake manifold absolute pressure is limited.
·
The following controls are performed based on conditions:
-
If the intake air temperature sensor is abnormal, the engine coolant temperature value is fixed at 80°C.
-
If the intake air temperature sensor is 15°C or less, the intake air temperature sensor value is used for the engine coolant temperature value.
-
If the intake air temperature sensor is 15°C or higher, the engine coolant temperature value is fixed at 110°C. |
Pass condition detected |
| P011515 | Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open |
·
The target intake manifold absolute pressure is limited.
·
The following controls are performed based on conditions:
-
If the intake air temperature sensor is abnormal, the engine coolant temperature value is fixed at 80°C.
-
If the intake air temperature sensor is 15°C or less, the intake air temperature sensor value is used for the engine coolant temperature value.
-
If the intake air temperature sensor is 15°C or higher, the engine coolant temperature value is fixed at 110°C. |
Pass condition detected |
| P01152A | Engine Coolant Temperature Sensor 1 Signal Stuck in Range |
·
The target intake manifold absolute pressure is limited.
·
The following controls are performed based on conditions:
-
If the intake air temperature sensor is abnormal, the engine coolant temperature value is fixed at 80°C.
-
If the intake air temperature sensor is 15°C or less, the intake air temperature sensor value is used for the engine coolant temperature value.
-
If the intake air temperature sensor is 15°C or higher, the engine coolant temperature value is fixed at 110°C. |
Pass condition detected |
| P011C62 | Charge Air Cooler Temperature/Intake Air Temperature Bank 1 Signal Compare Failure | The intake air temperature is fixed at a specified value. | Pass condition detected |
| P012012 | Throttle/Pedal Position Sensor/Switch "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off |
| P012014 | Throttle/Pedal Position Sensor/Switch "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P013013 | O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Open |
·
The supply of current to the air fuel ratio sensor is stopped.
·
Air fuel ratio learning is prohibited. |
Pass condition detected |
| P013613 | O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open |
·
The supply of current to the air fuel ratio sensor is stopped.
·
Air fuel ratio learning is prohibited. |
Pass condition detected |
| P018011 | Fuel Temperature Sensor "A" Circuit Short to Ground | The fuel temperature is fixed at 120°C. | Ignition switch off |
| P018015 | Fuel Temperature Sensor "A" Circuit Short to Battery or Open | The fuel temperature is fixed at 120°C. | Ignition switch off |
| P020112 | Cylinder 1 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020114 | Cylinder 1 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P020212 | Cylinder 2 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020214 | Cylinder 2 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P020312 | Cylinder 3 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020314 | Cylinder 3 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P020412 | Cylinder 4 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020414 | Cylinder 4 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P020512 | Cylinder 5 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020514 | Cylinder 5 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P020612 | Cylinder 6 Injector "A" Circuit Short to Battery | The engine power is limited. | Ignition switch off to ON or STA on |
| P020614 | Cylinder 6 Injector "A" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off to ON or STA on |
| P023A11 | Charge Air Cooler Coolant Pump Control Circuit Short to Ground | The intercooler coolant temperature is fixed at 120°C. | Pass condition detected |
| P023A12 | Charge Air Cooler Coolant Pump Control Circuit Short to Battery | Fully discharges the electric water pump assembly. | Pass condition detected |
| P023A14 | Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open | Fully discharges the electric water pump assembly. | Pass condition detected |
| P023A15 | Charge Air Cooler Coolant Pump Control Circuit Short to Battery or Open | The intercooler coolant temperature is fixed at 120°C. | Pass condition detected |
| P029907 | Turbocharger/Supercharger "A" Underboost Condition |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P029D00 | Cylinder 1 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02A100 | Cylinder 2 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02A500 | Cylinder 3 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02A900 | Cylinder 4 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02AD00 | Cylinder 5 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02B100 | Cylinder 6 - Injector Leaking |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P02EE00 | Cylinder 1 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P02EF00 | Cylinder 2 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P02F000 | Cylinder 3 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P02F100 | Cylinder 4 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P02F200 | Cylinder 5 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P02F300 | Cylinder 6 Injector Circuit Range/Performance |
·
Fuel injection stop of abnormal cylinder.
·
The engine power is limited. |
Ignition switch off |
| P033511 | Crankshaft Position Sensor "A" Circuit Short to Ground |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P033515 | Crankshaft Position Sensor "A" Circuit Short to Battery or Open |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P03351F | Crankshaft Position Sensor "A" Circuit Intermittent |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P03352A | Crankshaft Position Sensor "A" Signal Stuck in Range | The engine power is limited. | Pass condition detected |
| P033531 | Crankshaft Position Sensor "A" No Signal | The engine power is limited. | Pass condition detected |
| P034011 | Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground | The engine power is limited. | Pass condition detected |
| P034015 | Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open | The engine power is limited. | Pass condition detected |
| P03402A | Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range | The engine power is limited. | Pass condition detected |
| P034031 | Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal | The engine power is limited. | Pass condition detected |
| P040000 | Exhaust Gas Recirculation "A" Flow |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P040318 | Exhaust Gas Recirculation "A" Circuit Current Below Threshold |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P040319 | Exhaust Gas Recirculation "A" Circuit Current Above Threshold |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P040371 | Exhaust Gas Recirculation "A" Actuator Stuck |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Ignition switch off |
| P040911 | Exhaust Gas Recirculation Sensor "A" Circuit Short to Ground |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P040915 | Exhaust Gas Recirculation Sensor "A" Circuit Short to Battery or Open |
·
All catalyst controls are stopped.
·
The engine power is limited. |
Pass condition detected |
| P040A11 | Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low Circuit Short to Ground | The EGR gas temperature is switched to the estimated value. | Pass condition detected |
| P040A15 | Exhaust Gas Recirculation Temperature Sensor "A" Circuit High Circuit Short to Battery or Open | The EGR gas temperature is switched to the estimated value. | Pass condition detected |
| P042000 | Catalyst System Efficiency Below Threshold (Bank 1) | PM forced regeneration is prohibited. | Pass condition detected |
| P048014 | Fan 1 Control Circuit Low Circuit Short to Ground or Open |
1.
Electric control coupling fan is at maximum drive.
2.
When the engine coolant temperature reaches 113°C, air conditioning is stopped. |
1.
Pass condition detected
2.
The engine coolant temperature is below 108°C. |
| P04807F | Fan 1 Performance/Stuck Off Actuator Stuck Off |
1.
Electric control coupling fan is at maximum drive.
2.
When the engine coolant temperature reaches 113°C, air conditioning is stopped. |
1.
Pass condition detected
2.
The engine coolant temperature is below 108°C. |
| P048718 | Exhaust Gas Recirculation Throttle Control Circuit "A" Low Circuit Current Below Threshold | The engine power is limited. | Pass condition detected |
| P048719 | Exhaust Gas Recirculation Throttle Control Circuit "A" High Circuit Current Above Threshold | The engine power is limited. | Pass condition detected |
| P048771 | Exhaust Gas Recirculation Throttle Control Circuit "A" Range/Performance Actuator Stuck | The engine power is limited. | Ignition switch off |
| P050031 | Vehicle Speed Sensor "A" No Signal | The vehicle speed is fixed at 0 km/h (0 mph). | Pass condition detected |
| P052631 | Fan Speed Sensor Circuit No Signal No Signal | Electric control coupling fan is at maximum drive. | Pass condition detected |
| P054411 | Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Ground | PM forced regeneration is prohibited. | Pass condition detected |
| P054415 | Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open | PM forced regeneration is prohibited. | Pass condition detected |
| P05442A | Exhaust Gas Temperature Sensor 1 Bank 1 Signal Stuck In Range | PM forced regeneration is prohibited. | Pass condition detected |
| P056014 | System Voltage Circuit Short to Ground or Open | Generator command is maintained. | Pass condition detected and then ignition switch turned off |
| P060647 | Control Module Processor Watchdog/Safety MCU Failure | The engine is stalled. | Pass condition detected |
| P060694 | Control Module Processor Unexpected Operation |
·
The engine power is limited.
·
If the malfunction continues even after the engine power is limited, the engine stops. |
Ignition switch off |
| P060747 | Control Module Performance Bank 1 Watchdog/Safety MCU Failure | The engine is stalled. | Pass condition detected |
| P060787 | Control Module Performance Bank 1 Missing Message | The engine power is limited. | Pass condition detected |
| P060D49 | Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure | The engine power is limited. | Pass condition detected |
| P062712 | Fuel Pump "A" Control Circuit Short to Battery | The engine power is limited. | Ignition switch off |
| P062714 | Fuel Pump "A" Control Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P062D00 | Fuel Injector Driver Circuit Performance Bank 1 | The engine power is limited until the next trip. | Ignition switch off |
| P062D96 | Fuel Injector Driver Circuit Performance Bank 1 Component Internal Failure | The engine power is limited. | Ignition switch off |
| P062E96 | Fuel Injector Driver Circuit Performance Bank 2 Component Internal Failure | The engine power is limited. | Ignition switch off |
| P101A9E | A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On | A/F is fixed at a specified value. | Pass condition detected |
| P10C512 | 2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Battery |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P10C514 | 2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Ground or Open |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P122900 | Fuel Pump Valve Malfunction | The engine power is limited. | Ignition switch off |
| P125100 | Turbocharger Boost Control Malfunction |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P127112 | Pressure Discharge Valve Circuit Short to Battery | The engine power is limited. | Ignition switch off |
| P127114 | Pressure Discharge Valve Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P127273 | Fuel Regulator (EDU Drive) Actuator Stuck Closed | The engine power is limited. | Ignition switch off |
| P160700 | Cruise Control Input Processor | The engine is stalled. | Pass condition detected |
| P12A000 | Turbocharger/Supercharger Boost Control "C" Circuit Range/Performance |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P12A018 | Turbocharger/Supercharger Boost Control "C" Circuit Current Below Threshold |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P12A019 | Turbocharger/Supercharger Boost Control "C" Circuit Current Above Threshold |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P12A512 | Turbocharger/Supercharger Boost Control Position Sensor "C" Circuit Short to Battery |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P12A514 | Turbocharger/Supercharger Boost Control Position Sensor "C" Circuit Short to Ground or Open |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P12AC12 | Exhaust Control Valve Circuit Short to Battery |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to single turbo. |
Pass condition detected |
| P12AC14 | Exhaust Control Valve Circuit Short to Ground or Open |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P12B073 | Exhaust Control Valve Actuator Stuck Closed |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to single turbo. |
Ignition switch off |
| P12B100 | 2nd Turbocharger/Supercharger Overboost Condition |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P13A011 | Fuel Pressure Sensor #1(Sub CPU) Circuit Short to Ground |
·
The target injection pressure is limited when sensor #1 is malfunctioning.
·
The target injection pressure is limited when sensor #4 is malfunctioning.
·
The engine output is limited when sensor #1 and #4 are both malfunctioning (pending).
·
The engine output is limited to 10% when sensor #1 and #4 are both malfunctioning (confirmed).
·
The target injection pressure and engine output are limited if sensor #1, #2 and #6 are malfunctioning.
·
The target injection pressure and engine output are limited if sensor #4, #3 and #5 are malfunctioning. |
Ignition switch off |
| P13A015 | Fuel Pressure Sensor #1 (Sub CPU) Circuit Short to Battery or Open | ||
| P13A511 | Fuel Pressure Sensor #2 (Sub CPU) Circuit Short to Ground | ||
| P13A515 | Fuel Pressure Sensor #2 (Sub CPU) Circuit Short to Battery or Open | ||
| P13AA11 | Fuel Pressure Sensor #3 (Sub CPU) Circuit Short to Ground | ||
| P13AA15 | Fuel Pressure Sensor #3 (Sub CPU) Circuit Short to Battery or Open | ||
| P13B011 | Fuel Pressure Sensor #4 (Sub CPU) Circuit Short to Ground | ||
| P13B015 | Fuel Pressure Sensor #4 (Sub CPU) Circuit Short to Battery or Open | ||
| P13B511 | Fuel Pressure Sensor #5 (Sub CPU) Circuit Short to Ground | ||
| P13B515 | Fuel Pressure Sensor #5 (Sub CPU) Circuit Short to Battery or Open | ||
| P13BA11 | Fuel Pressure Sensor #6 (Sub CPU) Circuit Short to Ground | ||
| P13BA15 | Fuel Pressure Sensor #6 (Sub CPU) Circuit Short to Battery or Open | ||
| P13A02A | Fuel Pressure Sensor #1 (Sub CPU) Signal Stuck in Range |
·
The target injection pressure is limited when sensor #1 is malfunctioning.
·
The target injection pressure is limited when sensor #4 is malfunctioning.
·
The engine output is limited when sensor #1 and #4 are both malfunctioning (pending).
·
The engine output is limited to 10% when sensor #1 and #4 are both malfunctioning (confirmed).
·
The target injection pressure and engine output are limited if sensor #1, #2 and #6 are malfunctioning.
·
The target injection pressure and engine output are limited if sensor #4, #3 and #5 are malfunctioning. |
Battery cable disconnected or DTCs cleared |
| P13A52A | Fuel Pressure Sensor #2 (Sub CPU) Signal Stuck in Range | ||
| P13AA2A | Fuel Pressure Sensor #3 (Sub CPU) Signal Stuck in Range | ||
| P13B02A | Fuel Pressure Sensor #4 (Sub CPU) Signal Stuck in Range | ||
| P13B52A | Fuel Pressure Sensor #5 (Sub CPU) Signal Stuck in Range | ||
| P13BA2A | Fuel Pressure Sensor #6 (Sub CPU) Signal Stuck in Range | ||
| P13C013 | Fuel Temperature Sensor #1 Circuit Open | Fuel temperature is fixed to 40°C if sensors for 2 or more cylinders in the same bank are malfunctioning. | Ignition switch off |
| P13C513 | Fuel Temperature Sensor #2 Circuit Open | ||
| P13CA13 | Fuel Temperature Sensor #3 Circuit Open | ||
| P13D013 | Fuel Temperature Sensor #4 Circuit Open | ||
| P13D513 | Fuel Temperature Sensor #5 Circuit Open | ||
| P13DA13 | Fuel Temperature Sensor #6 Circuit Open | ||
| P13E011 | Fuel Pressure Sensor #1 (Main CPU) Circuit Short to Ground |
·
The target injection pressure is limited when sensor #1 is malfunctioning.
·
The target injection pressure is limited when sensor #4 is malfunctioning.
·
The engine output is limited when sensor #1 and #4 are both malfunctioning (pending).
·
The engine output is limited to 10% when sensor #1 and #4 are both malfunctioning (confirmed). |
Ignition switch off |
| P13E015 | Fuel Pressure Sensor #1 (Main CPU) Circuit Short to Battery or Open | ||
| P13E511 | Fuel Pressure Sensor #4 (Main CPU) Circuit Short to Ground | ||
| P13E515 | Fuel Pressure Sensor #4 (Main CPU) Circuit Short to Battery or Open | ||
| P167A87 | Injector #1 Missing Message | Fuel temperature is fixed to 40°C if sensors for 2 or more cylinders in the same bank are malfunctioning. | Ignition switch off |
| P167B87 | Injector #2 Missing Message | ||
| P167C87 | Injector #3 Missing Message | ||
| P167D87 | Injector #4 Missing Message | ||
| P167E87 | Injector #5 Missing Message | ||
| P167F87 | Injector #6 Missing Message | ||
| P168A00 | Injector #1 Internal EEPROM Malfunction |
·
The target injection pressure is limited when sensor #1 is malfunctioning.
·
The target injection pressure is limited when sensor #4 is malfunctioning.
·
The engine output is limited when sensor #1 and #4 are both malfunctioning (pending).
·
The engine output is limited to 10% when sensor #1 and #4 are both malfunctioning (confirmed).
·
The target injection pressure and engine output are limited if sensor #1, #2 and #6 are malfunctioning.
·
The target injection pressure and engine output are limited if sensor #4, #3 and #5 are malfunctioning. |
Ignition switch off |
| P168A44 | Injector #1 Internal EEPROM Data Memory Failure | ||
| P168A46 | Injector #1 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P168B00 | Injector #2 Internal EEPROM Malfunction | ||
| P168B44 | Injector #2 Internal EEPROM Data Memory Failure | ||
| P168B46 | Injector #2 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P168C00 | Injector #3 Internal EEPROM Malfunction | ||
| P168C44 | Injector #3 Internal EEPROM Data Memory Failure | ||
| P168C46 | Injector #3 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P168D00 | Injector #4 Internal EEPROM Malfunction | ||
| P168D44 | Injector #4 Internal EEPROM Data Memory Failure | ||
| P168D46 | Injector #4 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P168E00 | Injector #5 Internal EEPROM Malfunction | ||
| P168E44 | Injector #5 Internal EEPROM Data Memory Failure | ||
| P168E46 | Injector #5 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P168F00 | Injector #6 Internal EEPROM Malfunction | ||
| P168F44 | Injector #6 Internal EEPROM Data Memory Failure | ||
| P168F46 | Injector #6 Internal EEPROM Calibration / Parameter Memory Failure | ||
| P16B09F | Actuator Cut Circuit Stuck Off | The engine power is limited until the next trip. | Ignition switch off |
| P200C4B | Particulate Filter Over Temperature Bank 1 Over Temperature | PM forced regeneration is prohibited. | Pass condition detected |
| P200E4B | Catalyst System Over Temperature Bank 1 Over Temperature | PM forced regeneration is prohibited. | Ignition switch off |
| P203111 | Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Ground | PM forced regeneration is prohibited. | Pass condition detected |
| P203115 | Exhaust Gas Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open | PM forced regeneration is prohibited. | Pass condition detected |
| P20312A | Exhaust Gas Temperature Sensor 2 Bank 1 Signal Stuck In Range | PM forced regeneration is prohibited. | Pass condition detected |
| P20CB14 | Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open |
·
Engine output is limited at 10%.
·
PM forced regeneration is prohibited. |
Pass condition detected |
| P20CF00 | Exhaust Aftertreatment Fuel Injector "A" Stuck Open | Engine output is limited at 10%. | Pass condition detected |
| P212012 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery | The engine power is limited. | Ignition switch off |
| P212014 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P21201C | Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range | The engine power is limited. | Ignition switch off |
| P21201F | Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent | The engine power is limited. | Ignition switch off |
| P212099 | Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit | The engine power is limited. | Ignition switch off |
| P212512 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery | The engine power is limited. | Ignition switch off |
| P212514 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P21251F | Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent | The engine power is limited. | Ignition switch off |
| P21382B | Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled | The engine power is limited. | Ignition switch off |
| P219519 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Voltage Above Threshold |
w/ Urea SCR System:
The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped.
w/o Urea SCR System:
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Ignition switch off |
| P219618 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Voltage Below Threshold |
w/ Urea SCR System:
The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped.
w/o Urea SCR System:
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Ignition switch off |
| P220011 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Short to Ground | The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P220012 | NOx Sensor Circuit High Bank 1 Sensor 1 Circuit Short to Battery | The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P220013 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Open | The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P220512 | NOx Sensor Heater Control Circuit High Bank 1 Sensor 1 Circuit Short to Battery | The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P220514 | NOx Sensor Heater Control Circuit Low Bank 1 Sensor 1 Circuit Short to Ground or Open | The power to the No. 1 nitrogen oxides sensor and No. 1 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P222611 | Barometric Pressure Sensor "A" Circuit Short to Ground |
·
The atmospheric pressure is fixed at 60 kPa.
·
PM forced regeneration is prohibited. |
Pass condition detected |
| P222615 | Barometric Pressure Sensor "A" Circuit Short to Battery or Open |
·
The atmospheric pressure is fixed at 60 kPa.
·
PM forced regeneration is prohibited. |
Pass condition detected |
| P223711 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P223712 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P223713 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P223716 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P223717 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P225111 | O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P225112 | O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery | The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. | Pass condition detected |
| P229E11 | NOx Sensor Circuit Low Bank 1 Sensor 2 Circuit Short to Ground | The power to the No. 2 nitrogen oxides sensor and No. 2 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P229E12 | NOx Sensor Circuit High Bank 1 Sensor 2 Circuit Short to Battery | The power to the No. 2 nitrogen oxides sensor and No. 2 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P229E13 | NOx Sensor Circuit Low Bank 1 Sensor 2 Circuit Open | The power to the No. 2 nitrogen oxides sensor and No. 2 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P22A312 | NOx Sensor Heater Control Circuit High Bank 1 Sensor 2 Circuit Short to Battery | The power to the No. 2 nitrogen oxides sensor and No. 2 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P22A314 | NOx Sensor Heater Control Circuit Low Bank 1 Sensor 2 Circuit Short to Ground or Open | The power to the No. 2 nitrogen oxides sensor and No. 2 nitrogen oxides sensor heater is stopped. | Pass condition detected |
| P23AA72 | Turbocharger/Supercharger Bypass Valve "A" Actuator Stuck Open |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Ignition switch off |
| P24284B | Exhaust Gas Temperature Too High Bank 1 Over Temperature | PM forced regeneration is prohibited. | Ignition switch off |
| P242A11 | Exhaust Gas Temperature Sensor 3 Bank 1 Circuit Short to Ground | PM forced regeneration is prohibited. | Pass condition detected |
| P242A15 | Exhaust Gas Temperature Sensor 3 Bank 1 Circuit Short to Battery or Open | PM forced regeneration is prohibited. | Pass condition detected |
| P242A2A | Exhaust Gas Temperature Sensor 3 Bank 1 Signal Stuck In Range | PM forced regeneration is prohibited. | Pass condition detected |
| P244A00 | Particulate Filter Differential Pressure Too Low Bank 1 | PM forced regeneration is prohibited. | Ignition switch off |
| P244B00 | Particulate Filter Differential Pressure Too High Bank 1 |
·
The engine power is limited.
·
PM forced regeneration is prohibited. |
Ignition switch off |
| P245211 | Particulate Filter Pressure Sensor "A" Circuit Short to Ground | The particulate filter differential pressure is fixed at 0 kPa. | Pass condition detected |
| P245215 | Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open | The particulate filter differential pressure is fixed at 0 kPa. | Pass condition detected |
| P245800 | Particulate Filter Regeneration Duration Bank 1 | PM forced regeneration is prohibited. | Ignition switch off |
| P245A18 | Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Bank 1 Circuit Current Below Threshold | No. 2 EGR valve assembly (EGR bypass valve) energization is stopped. | Pass condition detected |
| P245A19 | Exhaust Gas Recirculation Cooler Bypass Control Circuit High Bank 1 Circuit Current Above Threshold | No. 2 EGR valve assembly (EGR bypass valve) energization is stopped. | Pass condition detected |
| P246300 | Particulate Filter Restriction - Soot Accumulation Bank 1 |
·
The engine power is limited.
·
PM forced regeneration is prohibited. |
Repair is complete |
| P249211 | Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit Low Bank 1 Circuit Short to Ground | No. 2 EGR valve assembly (EGR bypass valve) energization is stopped. | Pass condition detected |
| P249215 | Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit High Bank 1 Circuit Short to Battery or Open | No. 2 EGR valve assembly (EGR bypass valve) energization is stopped. | Pass condition detected |
| P24A571 | Exhaust Gas Recirculation Cooler Bypass Control Stuck/Open Bank 1 Actuator Stuck | No. 2 EGR valve assembly (EGR bypass valve) energization is stopped. | Pass condition detected |
| P256212 | Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High Circuit Short to Battery |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P256214 | Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low Circuit Short to Ground or Open |
·
The engine power is limited.
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P25F812 | Turbocharger/Supercharger Bypass Valve "C" Control Circuit High Circuit Short to Battery |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to single turbo. |
Pass condition detected |
| P25F814 | Turbocharger/Supercharger Bypass Valve "C" Control Circuit Low Circuit Short to Ground or Open |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to twin turbo. |
Pass condition detected |
| P263212 | Fuel Pump "B" Control Circuit High Circuit Short to Battery | The engine power is limited. | Ignition switch off |
| P263214 | Fuel Pump "B" Control Circuit Low Circuit Short to Ground or Open | The engine power is limited. | Ignition switch off |
| P2CD573 | Turbocharger/Supercharger Bypass Valve "C" Stuck Actuator Stuck Closed |
·
The engine power is limited (injection volume is restricted).
·
Turbo mode is fixed to single turbo. |
Ignition switch off |
| DTC No. | Detection Item | Fail-safe Operation | Fail-safe Deactivation Condition |
|---|---|---|---|
| P203A96 | Reductant Level Sensor "A" Circuit Component Internal Failure | Urea SCR system is stopped when urea level drops. | Pass condition detected |
| P204712 | Reductant Injection Valve Circuit High Bank 1 Unit 1 Circuit Short to Battery | Urea SCR system is stopped. | Pass condition detected |
| P204714 | Reductant Injection Valve Circuit Low Bank 1 Unit 1 Circuit Short to Ground or Open | Urea SCR system is stopped. | Pass condition detected |
| P204A12 | Reductant Pressure Sensor Circuit High Circuit Short to Battery | Urea SCR system is stopped. | Pass condition detected |
| P204A14 | Reductant Pressure Sensor Circuit Low Circuit Short to Ground or Open | Urea SCR system is stopped. | Pass condition detected |
| P206A87 | Reductant Quality Sensor Circuit Missing Message | Urea SCR system is stopped when urea level drops. | Pass condition detected |
| P208A14 | Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open | Urea SCR system is stopped. | Pass condition detected |
| P208A19 | Reductant Pump "A" Control Circuit High Circuit Current Above Threshold | Urea SCR system is stopped. | Pass condition detected |
| P208A96 | Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure | Urea SCR system is stopped. | Pass condition detected |
| P20B912 | Reductant Heater "A" Control Circuit High Circuit Short to Battery | Urea SCR system is stopped. | Pass condition detected |
| P20B914 | Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open | Urea SCR system is stopped. | Pass condition detected |
| P20B919 | Reductant Heater "A" Control Circuit Performance Circuit Current Above Threshold | Urea SCR system is stopped. | Pass condition detected |
| P20E900 | Reductant Pressure Too High | Urea SCR system is stopped. | Pass condition detected |
| P246E11 | Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Ground | Exhaust gas temperature after SCR is fixed at a specified value. | Pass condition detected |
| P246E15 | Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Battery or Open | Exhaust gas temperature after SCR is fixed at a specified value. | Pass condition detected |
| U010E87 | Lost Communication with Reductant Control Module Missing Message | Urea SCR system is stopped. | Pass condition detected |