Home › Engine / Hybrid System › F33A-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.07
RM38G0E _51 Engine / Hybrid System _106330 F33A-FTV ENGINE MECHANICAL _0485592 ENGINE UNIT G

F33A-FTV ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

a.
A184036C02
0.823,1.625 1.135,1.823 0.313,0.198 10 false *a
*a Measuring Area


Using a vernier caliper, measure the outside thread diameter of the cylinder head set bolt.

Standard Diameter:
for bolt A:

13.5 to 14.0 mm (0.531 to 0.551 in.)

for bolt B:

11.8 to 12.0 mm (0.465 to 0.472 in.)


Minimum Diameter:
for bolt A:

13.4 mm (0.528 in.)

for bolt B:

11.5 mm (0.453 in.)


HINT:

If a visual check reveals no excessively thin areas, check the center of the cylinder head set bolt (see illustration) and find the area that has the smallest diameter.


If the diameter is less than the minimum, replace the cylinder head set bolt.


Hide 13501B 2.INSPECT CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the camshaft. Check the oil clearance after replacing the camshaft.



b.
A475760

Inspect the cam lobe height.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake camshaft 38.75 to 38.85 mm (1.526 to 1.530 in.)
Exhaust camshaft 37.26 to 37.36 mm (1.467 to 1.471 in.)

Minimum Cam Lobe Height:
Item Specified Condition
Intake camshaft 38.55 mm (1.518 in.)
Exhaust camshaft 37.06 mm (1.459 in.)

HINT:

If the cam lobe height is less than the minimum, replace the camshaft.




c.
A492134C03
0.833,3.781 0.833,2.969 false 0.781,3.844 1.094,4 0.313,0.156 10 false *a 2.031,3.542 2.344,3.698 0.313,0.156 10 false *b
*a No. 1 Journal
*b Other journal


Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 Journal 29.969 to 29.985 mm (1.180 to 1.181 in.)
Other journal 23.959 to 23.975 mm (0.943 to 0.944 in.)

HINT:

If the journal diameter is not as specified, check the camshaft oil clearance.



Hide 3.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft bearing caps and camshaft journals.


b.

Place the camshafts on the cylinder head sub-assembly.


c.
A492135

Lay a strip of Plastigage across each of the camshaft journals.


d.
A492136C01
0.135,0.292 0.448,0.49 0.313,0.198 10 false *A 0.125,2.51 0.438,2.708 0.313,0.198 10 false *B
*A for Bank 1
*B for Bank 2


Temporarily install the No. 1 and No. 4 camshaft bearing cap with the 4 bolts by hand.

NOTICE:

Do not turn the camshafts.



e.

Install the No. 3 camshaft bearing caps with the 12 bolts.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 12 bolts.

A492137C01
0.542,0.438 0.854,0.594 0.313,0.156 10 false *A 3.958,0.406 4.271,0.563 0.313,0.156 10 false *B
*A for Bank 1 *B for Bank 2




f.
A492138C01
0.083,0.396 0.396,0.552 0.313,0.156 10 false *A 0.073,2.625 0.385,2.781 0.313,0.156 10 false *B 0.167,0.125 0.354,0.281 0.188,0.156 10 true 14 0.104,0.656 0.323,0.813 0.219,0.156 10 true 13 0.156,1.625 0.344,1.792 0.188,0.167 10 true 15 0.156,2.167 0.333,2.323 0.177,0.156 10 true 16 1.042,0.125 1.26,0.281 0.219,0.156 10 true 6 1.542,0.917 1.76,1.073 0.219,0.156 10 true 5 1.552,1.375 1.771,1.531 0.219,0.156 10 true 7 1.063,2.135 1.26,2.292 0.198,0.156 10 true 8 1.833,2.146 2.031,2.302 0.198,0.156 10 true 4 2.271,1.385 2.469,1.542 0.198,0.156 10 true 3 2.271,0.917 2.469,1.073 0.198,0.156 10 true 1 1.823,0.125 2.021,0.281 0.198,0.156 10 true 2 3.063,0.615 3.26,0.771 0.198,0.156 10 true 10 3.063,0.917 3.26,1.073 0.198,0.156 10 true 9 3.052,1.365 3.25,1.521 0.198,0.156 10 true 11 3.063,1.667 3.26,1.823 0.198,0.156 10 true 12 0.083,2.417 0.26,2.573 0.177,0.156 10 true 16 0.104,2.938 0.281,3.094 0.177,0.156 10 true 15 0.073,3.813 0.25,3.969 0.177,0.156 10 true 13 0.094,4.313 0.271,4.469 0.177,0.156 10 true 14 1.115,4.344 1.292,4.5 0.177,0.156 10 true 6 1.604,3.563 1.781,3.719 0.177,0.156 10 true 5 1.615,3.104 1.792,3.26 0.177,0.156 10 true 7 1.135,2.333 1.313,2.49 0.177,0.156 10 true 8 1.885,2.344 2.063,2.5 0.177,0.156 10 true 4 2.344,3.094 2.521,3.25 0.177,0.156 10 true 3 2.344,3.542 2.521,3.698 0.177,0.156 10 true 1 1.875,4.344 2.052,4.5 0.177,0.156 10 true 2 3.115,3.875 3.313,4.031 0.198,0.156 10 true 10 3.104,3.563 3.281,3.719 0.177,0.156 10 true 9 3.125,3.135 3.354,3.292 0.229,0.156 10 true 11 3.125,2.823 3.333,2.979 0.208,0.156 10 true 12
*A for Bank 1
*B for Bank 2


Uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)

for 10 mm head bolt of No. 3 camshaft bearing cap

10 N*m (102 kgf*cm, 7 ft.*lbf)


g.
A492138C02
0.052,2.594 0.365,2.792 0.313,0.198 10 false *B 0.073,0.375 0.385,0.573 0.313,0.198 10 false *A 0.115,0.104 0.323,0.26 0.208,0.156 10 false 3 0.146,2.167 0.365,2.323 0.219,0.156 10 false 1 1.042,0.156 1.26,0.313 0.219,0.156 10 false 11 1.083,2.135 1.302,2.292 0.219,0.156 10 false 9 1.802,0.135 2.021,0.292 0.219,0.156 10 false 15 1.823,2.146 2.042,2.302 0.219,0.156 10 false 13 3.073,0.906 3.229,1.104 0.156,0.198 10 true 8 3.073,0.656 3.229,0.854 0.156,0.198 10 true 7 3.094,1.365 3.25,1.563 0.156,0.198 10 true 6 3.073,1.656 3.229,1.854 0.156,0.198 10 true 5 0.188,1.615 0.344,1.813 0.156,0.198 10 true 2 0.177,0.646 0.333,0.844 0.156,0.198 10 true 4 2.26,1.365 2.469,1.563 0.208,0.198 10 true 14 2.26,0.927 2.458,1.125 0.198,0.198 10 true 16 1.563,1.375 1.802,1.573 0.24,0.198 10 true 10 1.563,0.917 1.76,1.115 0.198,0.198 10 true 12 0.125,2.385 0.292,2.542 0.167,0.156 10 false 1 0.083,2.927 0.24,3.125 0.156,0.198 10 true 2 0.083,3.76 0.24,3.958 0.156,0.198 10 true 4 0.104,4.323 0.26,4.521 0.156,0.198 10 true 3 1.125,2.344 1.281,2.542 0.156,0.198 10 true 9 1.865,2.333 2.021,2.531 0.156,0.198 10 true 13 1.604,3.094 1.813,3.292 0.208,0.198 10 true 10 1.604,3.531 1.813,3.719 0.208,0.188 10 true 12 1.146,4.333 1.354,4.51 0.208,0.177 10 true 11 1.885,4.344 2.094,4.51 0.208,0.167 10 true 15 2.344,3.552 2.542,3.729 0.198,0.177 10 true 16 2.354,3.094 2.531,3.292 0.177,0.198 10 true 14 3.104,2.792 3.26,2.99 0.156,0.198 10 true 5 3.125,3.094 3.281,3.292 0.156,0.198 10 true 6 3.104,3.542 3.26,3.74 0.156,0.198 10 true 8 3.104,3.844 3.26,4.042 0.156,0.198 10 true 7
*A for Bank 1
*B for Bank 2


Uniformly loosen and remove the 16 bolts in the sequence shown in the illustration.


h.
A492139

Measure the Plastigage at its widest point.

Standard oil clearance:

0.025 to 0.062 mm (0.000984 to 0.00244 in. )


Maximum oil clearance:

0.072 mm (0.00283 in. )


NOTICE:
·

If the oil clearance is more than the maximum, replace the camshaft.


·

If necessary, replace the cylinder head sub-assembly.




i.

Remove the Plastigage completely.


j.

Remove the camshafts.


Hide 13801 4.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A366101

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 5.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign objects.

·

Use only clean engine oil.



a.

Place the valve lash adjuster assembly into a container full of new engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  

A377673C01
2.188,0.594 2.635,0.594 false 2.104,1.271 2.677,1.271 false 2.125,2.344 2.313,2.344 2.313,2.344 2.875,2.083 true 5.25,1.344 5.438,0.719 5.438,0.719 5.625,0.719 true 1.083,2.49 1.083,2.271 true 2.135,1.771 2.771,1.771 true 2.885,2.5 2.885,2.281 true 1.24,1.771 1.875,1.771 true 1.865,2.344 1.688,2.344 1.688,2.344 1.146,2.115 true 2.698,1 2.219,0.854 2.219,0.854 2.083,0.854 false 1.302,1.073 1.719,0.854 1.719,0.854 1.844,0.854 false 1.427,0.604 1.781,0.604 false 1.354,1.271 1.875,1.271 false 1.063,0.083 1.375,0.281 0.313,0.198 10 false *a 2.854,0.083 3.167,0.281 0.313,0.198 10 false *b 1.906,0.781 2.208,0.979 0.302,0.198 10 false *c 1.927,1.188 2.104,1.365 0.177,0.177 10 false *d 1.938,1.688 2.125,1.875 0.188,0.188 10 false *e 1.927,2.271 2.24,2.469 0.313,0.198 10 false *f 1,2.49 1.313,2.688 0.313,0.198 10 false *g 2.813,2.49 3.125,2.688 0.313,0.198 10 false *g 1.865,0.51 2.156,0.688 0.292,0.177 10 false SST 5.677,0.635 5.979,0.833 0.302,0.198 10 false SST
*a CORRECT *b INCORRECT
*c Tapered Path *d Plunger
*e Low Pressure Chamber *f Check Ball
*g High Pressure Chamber - -



c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


HINT:

If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster assembly with a new one.



Hide 13506A 6.INSPECT NO. 1 CHAIN SUB-ASSEMBLY

a.
A382970C03
1.625,0.927 1.938,1.125 0.313,0.198 10 false *a
*a Measurement Area


Using a spring scale, pull the No. 1 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

137.38 mm (5.409 in.)


HINT:

Perform the measurement at 3 random places. If a measurement is more than the maximum, replace the No. 1 chain sub-assembly.



Hide 13507 7.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A382970C06
1.625,0.927 1.938,1.125 0.313,0.198 10 false *a
*a Measurement Area


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

137.38 mm (5.409 in.)


HINT:

Perform the measurement at 3 random places. If a measurement is more than the maximum, replace the No. 2 chain sub-assembly.



Hide 15100K 8.INSPECT OIL PUMP CHAIN

a.
A382970C01
1.625,0.906 1.938,1.104 0.313,0.198 10 false *a
*a Measurement Area


Using a spring scale, pull the oil pump chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

115.72 mm (4.556 in.)


HINT:

Perform the measurement at 3 random places. If a measurement is more than the maximum, replace the oil pump chain.



Hide 15163C 9.INSPECT OIL PUMP DRIVE SHAFT SPROCKET

a.
A493175

Place the oil pump drive shaft sprocket around the oil pump drive shaft sprocket.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft sprocket with the oil pump chain.

Minimum Gear Diameter (with Oil Pump Chain):

85.63 mm (3.371 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the oil pump chain and oil pump drive shaft sprocket.



Hide 13616A 10.INSPECT SUPPLY PUMP SHAFT SPROCKET

a.
A493178

Wrap the No. 1 chain sub-assembly around the supply pump shaft sprocket place for the No. 1 chain sub-assembly.


b.

Using a vernier caliper, measure the supply pump shaft sprocket with the No. 1 chain sub-assembly.

Minimum gear diameter (with No. 1 chain sub-assembly):

114.63 mm (4.513 in.)


HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and supply pump shaft sprocket.


c.
A497854

Wrap the No. 2 chain sub-assembly around the supply pump shaft sprocket place for the No. 2 chain sub-assembly.


d.

Using a vernier caliper, measure the supply pump shaft sprocket with the No. 2 chain sub-assembly.

Minimum gear diameter (with No. 2 chain sub-assembly):

59.77 mm (2.353 in.)


HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and supply pump shaft sprocket.


Hide 13411 11.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A497855

Wrap the No. 1 chain sub-assembly around the crankshaft timing sprocket place for the No. 1 chain sub-assembly.


b.

Using a vernier caliper, measure the crankshaft timing sprocket with the No. 1 chain sub-assembly.

Minimum gear diameter (with No. 1 chain sub-assembly):

87.52 mm (3.446 in.)


HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and crankshaft timing sprocket.


Hide 13523G 12.INSPECT CAMSHAFT TIMING SPROCKET

a.
A493176

Wrap the No. 2 chain sub-assembly around the camshaft timing sprocket.


b.

Using a vernier caliper, measure the camshaft timing sprocket diameter with the No. 2 chain sub-assembly.

Minimum gear diameter (with No. 2 chain sub-assembly):

87.52 mm (3.446 in. )


HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing sprocket.


Hide 13529G 13.INSPECT NO. 2 CAMSHAFT TIMING SPROCKET

a.
A493177

Wrap the No. 2 chain sub-assembly around the sprocket.


b.

Using a vernier caliper, measure the No. 2 camshaft timing sprocket diameter with the No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

87.52 mm (3.446 in. )


HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket.


Hide 13540 14.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A492140C01
2.719,1.552 3.063,1.094 false 1.479,0.396 1.969,0.51 false 3.063,0.958 3.375,1.115 0.313,0.156 10 false *a 1.281,0.302 1.594,0.458 0.313,0.156 10 false *b
*a Plunger
*b Stopper Pin


Move the stopper pin to release the lock. Push the plunger and check that it moves smoothly. If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 15.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A492140C02
2.75,1.563 3.021,1.094 false 1.375,0.323 1.969,0.448 false 3.042,0.958 3.354,1.115 0.313,0.156 10 false *a 1.219,0.229 1.531,0.385 0.313,0.156 10 false *b
*a Plunger
*b Stopper Pin


Move the stopper pin to release the lock. Push the plunger and check that it moves smoothly. If necessary, replace the No. 2 chain tensioner assembly.


Hide 13560A 16.INSPECT NO.3 CHAIN TENSIONER ASSEMBLY

a.
A497856C02
1.188,0.26 1.854,0.49 true 2.719,1.708 3.031,1.427 true 3,1.229 3.313,1.385 0.313,0.156 10 false *a 1.031,0.156 1.344,0.313 0.313,0.156 10 false *b
*a Plunger
*b Stopper Pin


Move the stopper pin to release the lock. Push the plunger and check that it moves smoothly. If necessary, replace the No. 3 chain tensioner assembly.


Hide 13559 17.INSPECT CHAIN TENSIONER SLIPPER

a.
A492141C01
0.448,0.052 0.76,0.208 0.313,0.156 10 false A 1.354,0.458 1.542,0.625 0.188,0.167 10 true A 3.021,0.99 3.333,1.146 0.313,0.156 10 false *a 2.229,1.958 2.688,2.115 0.458,0.156 10 false A-A
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13559F 18.INSPECT CHAIN TENSIONER SLIPPER LH

a.
A492141C02
0.458,0.021 0.771,0.177 0.313,0.156 10 true A 1.344,0.479 1.521,0.635 0.177,0.156 10 true A 3.031,0.99 3.323,1.146 0.292,0.156 10 true *a 2.24,1.969 2.76,2.125 0.521,0.156 10 true A-A
*a Depth


Measure the wear depth of the chain tensioner slipper LH.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper LH.



Hide 13559E 19.INSPECT CHAIN TENSIONER SLIPPER RH

a.
A492141C03
0.458,0.01 0.615,0.208 0.156,0.198 10 true A 1.375,0.448 1.531,0.646 0.156,0.198 10 true A 2.229,1.938 2.677,2.135 0.448,0.198 10 true A-A 3.042,1 3.375,1.198 0.333,0.198 10 true *a
*a Depth


Measure the wear depth of the chain tensioner slipper RH.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper RH.



Hide 13561 20.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A492142C01
3.104,1.115 3.417,1.271 0.313,0.156 10 false *a 2.302,1.938 2.74,2.104 0.438,0.167 10 false A-A 0.594,0.063 0.75,0.26 0.156,0.198 10 true A 1.49,0.479 1.646,0.677 0.156,0.198 10 true A
*a Depth


Measure the wear depth of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13562 21.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A492142C02
3.115,1.083 3.292,1.344 0.177,0.26 10 false *a 0.583,0.094 0.844,0.25 0.26,0.156 10 true A 1.479,0.531 1.74,0.688 0.26,0.156 10 true A 2.26,1.875 2.646,2.031 0.385,0.156 10 true A-A
*a Depth


Measure the wear depth of the No. 2 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 2 chain vibration damper.



Hide 13563 22.INSPECT NO. 3 CHAIN VIBRATION DAMPER

a.
A492142C03
0.563,0.063 0.719,0.26 0.156,0.198 10 true A 1.479,0.5 1.635,0.698 0.156,0.198 10 true A 2.271,1.875 2.74,2.073 0.469,0.198 10 true A-A 3.083,1.104 3.427,1.271 0.344,0.167 10 true *a
*a Depth


Measure the wear depth of the No. 3 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 3 chain vibration damper.