Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  U010087  Lost Communication With ECM/PCM "A" Missing Message  U010187  Lost Communication with TCM Missing Message  U011487  Lost Communication with Four-Wheel Drive Clutch Control Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U012987  Lost Communication With Brake System Control Module Missing Message  U014087  Lost Communication with Body Control Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  U015587  Lost Communication with Instrument Panel Cluster (IPC) Control Module  U016487  Lost Communication with HVAC Control Module Missing Message  U111087  Lost Communication with Intuitive Parking Assist Module Missing Message  U114C87  Lost Communication with Air Suspension Control Module "A" Missing Message  U117087  Lost Communication With Brake System Control Module(ch2) Missing Message  


DESCRIPTION

The engine stop and start ECU communicates with the engine control system, automatic transmission system, transfer system, electronically control brake system, power steering system, air conditioning system, airbag system, adaptive variable suspension system, combination meter assembly, main body ECU (multiplex network body ECU), parking support brake system and integration control and panel sub-assembly via CAN communication.

If there is a communication error between the engine stop and start ECU and any of the systems, the engine stop and start ECU stores DTCs and illuminates the stop and start cancel indicator except when there is a communication error with the meter/gauge system.

HINT:
·

When there is an open in the output side of the backup boost converter (built into the engine stop and start ECU), power to the system with the open is cut off. The engine stop and start ECU stores CAN communication DTCs for the system with the open and stop and start system DTC P323A16.

·

When the backup boost converter (built into the engine stop and start ECU) detects overcurrent in any of the circuits it supplies power to, it shuts off the circuit. The engine stop and start ECU stores CAN communication DTCs for the system which circuit was shut off and stores stop and start system DTC P323A19.

e.g.: When the backup boost converter (built into the engine stop and start ECU) detects overcurrent in the power source circuit of the steering sensor and cuts off power supply, the engine stop and start ECU stores DTCs U012687 and P323A19.



DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
U010087 Lost Communication With ECM/PCM "A" Missing Message No communication between the engine stop and start ECU and ECM for 1 second.
·

Wire harness or connector

·

Engine stop and start ECU

·

ECM


Blinks SAE Code: U0100
U010187 Lost Communication with TCM Missing Message No communication between the engine stop and start ECU and TCM for 1 second.
·

Wire harness or connector

·

Engine stop and start ECU

·

TCM


Blinks SAE Code: U0101
U011487 Lost Communication with Four-Wheel Drive Clutch Control Module Missing Message No communication between the engine stop and start ECU and ECM for 1 second.
·

Wire harness or connector

·

Engine stop and start ECU

·

4 wheel drive control ECU


Blinks SAE Code: U0114
U012687 Lost Communication with Steering Angle Sensor Module Missing Message No communication between the engine stop and start ECU and steering sensor for 1 second.
·

Wire harness or connector

·

Engine stop and start ECU

·

Steering sensor


Blinks SAE Code: U0126
U012987 Lost Communication With Brake System Control Module Missing Message No communication between the engine stop and start ECU and skid control ECU (brake actuator assembly) for 2.22 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Skid control ECU (Brake actuator assembly)


Blinks SAE Code: U0129
U014087 Lost Communication with Body Control Module Missing Message No communication between the engine stop and start ECU and the main body ECU (multiplex network body ECU) for 3.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Main body ECU (multiplex network body ECU)


Blinks SAE Code: U0140
U015187 Lost Communication with Restraints Control Module Missing Message No communication between the engine stop and start ECU and airbag ECU assembly for 10.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Airbag ECU assembly


Blinks SAE Code: U0151
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module No communication between the engine stop and start ECU and the combination meter assembly for 3.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Combination meter assembly


Blinks SAE Code: U0155
U016487 Lost Communication with HVAC Control Module Missing Message No communication between the engine stop and start ECU and air conditioning amplifier assembly for 10.6 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Air conditioning amplifier assembly


Blinks SAE Code: U0164
U111087 Lost Communication with Intuitive Parking Assist Module Missing Message No communication between the engine stop and start ECU and the clearance warning ECU assembly for 1 second.
·

Wire harness or connector

·

Engine stop and start ECU

·

Clearance warning ECU assembly


Blinks SAE Code: U1110
U114C87 Lost Communication with Air Suspension Control Module "A" Missing Message No communication between the engine stop and start ECU and suspension control ECU for 1.1 seconds.
·

Wire harness or connector

·

Engine stop and start ECU

·

Suspension control ECU


Blinks SAE Code: U114C
U117087 Lost Communication With Brake System Control Module(ch2) Missing Message No communication between the engine stop and start ECU and the skid control ECU (brake actuator assembly) for 3 second
·

Wire harness or connector

·

Engine stop and start ECU

·

Skid control ECU (brake actuator assembly)


Blinks SAE Code: U1170

CAUTION / NOTICE / HINT

HINT:

If any of CAN communication system DTCs and sensor malfunction DTCs related to the CAN communication system are output simultaneously, perform troubleshooting for the CAN communication system DTCs first, then for the sensor malfunction DTCs.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the ignition switch off and wait for 30 seconds or more.


b.

Turn the ignition switch to ON.


c.

Start the engine.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


f.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTC U010087, U010187, U011487, U012687, U012987, U014087, U015187, U015587, U016487, U111087, U114C87 or U117087 is output A
DTC U010087, U010187, U011487, U012687, U012987, U014087, U015187, U015587, U016487, U111087, U114C87 or U117087 is not output B




A

B