DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | 1 to 999999 | Same as actual total distance traveled | For the unit, refer to "Total Distance Traveled - Unit" |
| Total Distance Traveled - Unit | Total distance traveled unit | km or mile | km: km mile: mile |
- |
| PKSB (O) Equipped Information | Parking support brake (static objects) installation information | Without, With or Unknown | Without: No parking support brake (static objects) With: Parking support brake (static objects) Unknown: Unknown |
- |
| PKSB (V) Equipped Information | Parking support brake (rear crossing vehicles) installation information | Without, With or Unknown | Without: No parking support brake (rear crossing vehicles) With: Parking support brake (rear crossing vehicles) Unknown: Unknown |
- |
| PKSB (P) Equipped Information | Parking support brake (rear pedestrians) installation information | Without, With or Unknown | Without: No parking support brake (rear pedestrians) With: Parking support brake (rear pedestrians) Unknown: Unknown |
- |
| Ultrasonic Sensor (Front Left Center) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Front Left Center) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Front Right Center) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Front Right Center) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Front Left Corner) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Front Left Corner) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Front Right Corner) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Front Right Corner) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Left Center) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Left Center) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Right Center) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Right Center) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 7.65 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 7.65 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Left Corner) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Left Corner) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Right Corner) Target Distance - First Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| Ultrasonic Sensor (Rear Right Corner) Target Distance - Second Wave | Distance from the ultrasonic sensor to the target | Unknown, Not Detected or 0 to 5.1 m | Unknown: Outside sensor operation conditions Not Detected: Not detected 0 to 5.1 m: Detected distance |
- |
| PKSB Main Switch | Input signal for parking support brake system | OFF or ON | OFF: Parking support brake system OFF ON: Parking support brake system ON |
- |
| Bumper Type | Registered bumper type | Unknown, 1, 2, 3 or 4 | Unknown: Not registered 1: For standard type, w/ garnish (front bumper guard) 2: For aero type, except GR SPORT or for aero type, for GR SPORT |
- |
| Adjustment Mode | Adjustment mode | Normal Mode or Dealer Mode | Normal Mode: Not dealer adjustment mode Dealer Mode: Dealer adjustment mode |
- |
| PKSB (O) Function | Status of parking support brake (static objects) function | ON or OFF | ON: Parking support brake (static objects) function ON OFF: Parking support brake (static objects) function OFF |
- |
| PKSB (O) Target Stopping Distance | Target stop distance setting status of parking support brake (static objects) function | Close or Far | Setting of customized parameter | - |
| PKSB Switch State Stored | Setting of the parking support brake system main switch status memory | Stored or Not stored | Setting of customized parameter | - |
| PCS Cooperate Function | Status of pre-collision system cooperate function | ON or OFF | ON: Pre-collision system cooperate function ON OFF: Pre-collision system cooperate function OFF |
- |
| PKSB (V) Function | Status of parking support brake (rear crossing vehicles) function | ON or OFF | ON: Parking support brake (rear crossing vehicles) function ON OFF: Parking support brake (rear crossing vehicles) function OFF |
- |
| PKSB (V) Operation Timing Setting | Displays the operation timing setting of the parking support brake (rear crossing vehicles) function | Late or Standard | Late: Late timing Standard: Standard timing |
- |
| PKSB (V) Sensitivity | Displays the sensitivity setting of the parking support brake (rear crossing vehicles) function | Standard or Low | Standard: Standard sensitivity Low: Low sensitivity |
- |
| PKSB (P) Function | Setting of the parking support brake (rear pedestrians) function | ON or OFF | ON: Parking support brake (rear pedestrians) function ON OFF: Parking support brake (rear pedestrians) function OFF |
- |
| PKSB (P) Target Stopping Distance | Setting of the activation timing of the parking support brake (rear pedestrians) function | Close or Normal | Close: Near Normal: Normal |
- |
| PKSB (P) Width Adjustment (Y Axis) | Setting of the sensitivity of the parking support brake (rear pedestrians) function | Narrow or Normal | Narrow: Near Normal: Normal |
- |
| Software Inconsistency with ENG/HV/EV Control Module | ENG/HV/EV specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2601 is output if Yes |
| Software Inconsistency with Body Control Module | Main body ECU (multiplex network body ECU) specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2603 is output if Yes |
| Software Inconsistency with Rear Side Rader Sensor | Blind spot monitor sensor specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2623 is output if Yes |
| Software Inconsistency with Rear Camera | Television camera assembly specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2621 is output if Yes |
| Memorizing Vehicle Information Not Programmed | Vehicle specification not programmed | Complete or Incomplete | Complete: Vehicle specification writing complete Incomplete: Vehicle specification writing incomplete |
RoB X2617 is output if Incomplete |
| Ultrasonic Sensor (Front) ID Not Registered | Ultrasonic sensor (front) ID registration status | Registered or Not Registered | Registered: ID registered Not Registered: ID not registered |
RoB X20C0 is output if Not Registered |
| Ultrasonic Sensor (Rear) ID Not Registered | Ultrasonic sensor (rear) ID registration status | Registered or Not Registered | Registered: ID registered Not Registered: ID not registered |
RoB X20C1 is output if Not Registered |
| Ultrasonic Sensor (Front Side) ID Not Registered | Ultrasonic sensor (front side) ID registration status | Registered or Not Registered | Registered: ID registered Not Registered: ID not registered |
RoB X20C2 is output if Not Registered |
| Ultrasonic Sensor (Rear Side) ID Not Registered | Ultrasonic sensor (rear side) ID registration status | Registered or Not Registered | Registered: ID registered Not Registered: ID not registered |
RoB X20C3 is output if Not Registered |
| PKSB Detection Area Adjustment Incomplete | Adjustment status of ultrasonic sensor | Complete or Incomplete | Complete: Ultrasonic sensor adjustment complete Incomplete: Ultrasonic sensor adjustment not complete |
- |
| Memorizing the Steering Angle Zero Point Incomplete | Steering neutral point storage status | Complete or Incomplete | Complete: Steering neutral point storage complete Incomplete: Steering neutral point storage incomplete |
- |
| Rear Side Radar Sensor Optical Axis Not Adjusted | Beam axis adjustment registration status of the blind spot monitor | Complete or Incomplete | Complete: Beam axis adjusted Incomplete: Beam axis adjustment not registered |
RoB X203B is output if Incomplete |
| Software Inconsistency with Brake Control Module | Skid control ECU specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2605 is output if Yes |
| Software Inconsistency with Image Processing Module "B" | Parking assist ECU specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X262B is output if Yes |
| Software Inconsistency with Steering Angle Sensor Module | Steering sensor specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X260D is output if Yes |
| Software Inconsistency with VGRS Control Module | Front steering control ECU specification information mismatch | No or Yes | No: Specification information match Yes: Specification information mismatch |
RoB X2609 is output if Yes |
| Clearance Warning ECU Low Voltage | Low voltage for clearance warning ECU assembly | Normal or Low Voltage | Normal: Clearance warning ECU assembly voltage normal Low Voltage: Clearance warning ECU assembly voltage malfunction |
RoB X20DE is output if Low Voltage |
| Zero Point Calibration of Steering Angle Sensor Undone | Steering angle sensor zero point not calibrated | Normal or Not calibration | Normal: Steering angle sensor zero point calibration complete Not calibration: Steering angle sensor zero point calibration not complete |
- |
| Steering Angle Sensor Malfunction | Steering sensor internal malfunction | No or Yes | No: Steering sensor normal Yes: Steering sensor malfunction |
RoB X2001 is output if Yes |
| Engine Control Module Malfunction | Powertrain system malfunction | No or Yes | No: SFI system or ECD system normal Yes: SFI system or ECD system malfunction |
RoB X2087 is output if Yes |
| Hybrid/EV Powertrain Control System Malfunction | HV/EV system malfunction | No or Yes | No: Hybrid control system normal Yes: Hybrid control system malfunction |
RoB X2005 is output if Yes |
| Brake Control System Malfunction | Brake system malfunction | No or Yes | No: Electronically controlled brake system normal Yes: Electronically controlled brake system malfunction |
RoB X2003 is output if Yes |
| Electric Parking Brake Control Module Malfunction | Electric parking brake system malfunction | No or Yes | No: Electric parking brake system normal Yes: Electric parking brake system malfunction |
- |
| Power Steering Control Module Malfunction | Power steering system malfunction | No or Yes | No: Power steering system normal Yes: Power steering system malfunction |
RoB X208E is output if Yes |
| Acceleration Sensor Malfunction | Yaw rate sensor malfunction | No or Yes | No: Electronically controlled brake system normal Yes: Electronically controlled brake system malfunction |
RoB X204A is output if Yes |
| Circumference Monitoring Camera Control Module Malfunction | Panoramic view monitor control system malfunction | No or Yes | No: Panoramic view monitor system normal Yes: Panoramic view monitor system malfunction |
RoB X20B0 is output if Yes |
| Rear Side Radar Sensor Malfunction | Blind spot monitor system malfunction | No or Yes | No: Blind spot monitor system normal Yes: Blind spot monitor system malfunction |
RoB X2038 is output if Yes |
| Rear Side Radar Sensor Temporarily Unavailable | Blind spot monitor system malfunction | No or Yes | No: Blind spot monitor system normal Yes: Blind spot monitor system temporarily unavailable |
RoB X203A is output if Yes |
| Ambient Temperature Sensor Circuit | Ambient temperature sensor malfunction | No or Yes | No: Air conditioning system normal Yes: Air conditioning system malfunction |
RoB X2077 is output if Yes |
| Rear Camera Malfunction | Television camera assembly malfunction | No or Yes | No: Panoramic view monitor system normal Yes: Panoramic view monitor system malfunction |
RoB X20B1 is output if Yes |
| Rear Camera Temporarily Unavailable | Television camera assembly malfunction | No or Yes | No: Panoramic view monitor system normal Yes: Panoramic view monitor system malfunction |
RoB X20B2 is output if Yes |
| Communication Error from Clearance Warning Control Module to Power Steering Control Module | Power steering system communication malfunction | No or Yes | No: Power steering system normal Yes: Power steering system malfunction |
RoB X20D6 is output if Yes |
| Communication Error from Clearance Warning Control Module to Brake Control Module | Brake system communication malfunction | No or Yes | No: Electronically controlled brake system normal Yes: Electronically controlled brake system malfunction |
RoB X20D5 is output if Yes |
| Communication Error from Clearance Warning Control Module to Image Processing Module "B" | Panoramic view monitor system communication malfunction | No or Yes | No: Panoramic view monitor system normal Yes: Panoramic view monitor system malfunction |
RoB X20B0 is output if Yes |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Lamp Relay | Stop lights | OFF / ON | Test possible at vehicle speed of 0 km/h (0 mph) |
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Buzzer | No. 1 clearance warning buzzer | OFF / ON | Confirm that the vehicle is stopped and the ignition switch is ON |
| Rear Buzzer | No. 2 clearance warning buzzer | OFF / ON | Confirm that the vehicle is stopped and the ignition switch is ON |