Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) D

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  INITIALIZATION  


PERFORM ROAD TEST TO ALLOW TCM TO LEARN


CAUTION:

Perform the following procedures while strictly observing all traffic laws and speed limits.


NOTICE:
·

Do not accelerate or decelerate rapidly.

·

This test must be performed after checking and adjusting the engine.

·

Perform this test with the ATF (Automatic Transmission Fluid) at the normal operating temperature: 50 to 80°C (122 to 176°F).



HINT:
·

When the TCM is replaced, perform A/T Code Registration after replacement, and then perform drive learning.

·

Perform drive learning after replacing the transmission valve body assembly, solenoid (SL1, SL2, SL3, SL4, SL5 and/or SL6) valves or engine assembly.



a.

The Road Test procedure is as follows:

i.

According to the replaced parts, perform the appropriate road test shown below.

Replaced Parts Road Test
·

TCM

·

Transmission valve body assembly

·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Engine assembly


Perform pattern 1 and pattern 2

Monitor the accelerator opening angle with the GTS.

With the vehicle stopped and the shift lever in P, check the pedal depressed amount to achieve the accelerator opening angle at 15 to 20%.

Perform pattern 1 with the accelerator opening angle at 15 to 20%.

With the vehicle stopped and the shift lever in P, check the pedal depressed amount to achieve the accelerator opening angle at 25 to 35%.

Perform pattern 1 with the accelerator opening angle between 25 to 35%.


Pattern 1:

With the shift lever in D, accelerate to the maximum possible speed, and then gently decelerate to approximately 5 km/h.

If the shift shock is large, repeat this procedure until shift shock no longer occurs.


Pattern 2:

With the shift lever in D, accelerate to the maximum possible speed, move the shift lever to M, then shift down to M2 while gently decelerating.



C377137E01
3.927,3.469 4.073,3.594 4.073,3.594 5.417,3.594 false 4.531,3.594 4.427,3.469 false 5.031,3.594 4.927,3.469 false 3.104,0.802 3.469,1.26 3.469,1.26 3.677,1.26 true 3.479,1.25 3.438,0.833 true 0.073,0.094 1.479,0.323 1.406,0.229 10 false Road Test Pattern 1: 0.083,0.385 0.875,0.635 0.792,0.25 10 false (D position) 0.063,2.073 1.531,2.333 1.469,0.26 10 false Road Test Pattern 2: 0.083,2.354 0.896,2.615 0.813,0.26 10 false (M position) 2.24,0.469 3.271,0.708 1.031,0.24 10 false Accel. Learning 5.177,0.469 6.24,0.74 1.063,0.271 10 false Decel. Learning 1.979,0.375 2.208,0.615 0.229,0.24 10 false *2 0.896,1.01 2.198,1.563 1.302,0.552 10 false 10 km/h (6.22 mph) 2.313,3.51 3.677,3.76 1.365,0.25 10 false Approximately 4 sec. 5.469,3.49 6.833,3.74 1.365,0.25 10 false Approximately 2 sec. 6.073,2.854 6.719,3.083 0.646,0.229 10 false M3→M2 5.563,2.646 6.208,2.875 0.646,0.229 10 false M4→M3 5.052,2.458 5.698,2.688 0.646,0.229 10 false M5→M4 4.563,2.26 5.208,2.49 0.646,0.229 10 false M6→M5 2.479,2.063 3.5,2.281 1.021,0.219 10 false M6 position*5 2.969,1.771 5.458,2.01 2.49,0.24 10 false Accelerator and brake pedals released 2.031,1.792 2.479,2 0.448,0.208 10 false D→M 1.969,2.292 2.198,2.531 0.229,0.24 10 false *4 4.094,0.26 4.323,0.5 0.229,0.24 10 false *1 3.719,1.177 3.948,1.417 0.229,0.24 10 false *3 0.833,2.854 2.417,3.135 1.583,0.281 10 false 30 km/h (18.65 mph)

HINT:

*1: Use the correct timing when transitioning from acceleration learning to deceleration learning.

*2: Acceleration learning accelerates to the maximum possible speed with the accelerator pedal in a fixed position, whereas deceleration learning decelerates with the brake pedal in a fixed position.

*3: Acceleration learning is divided into two patterns: 15 to 20% and 25 to 35% patterns. Deceleration learning is also divided into two patterns: Slow braking with the brake on and off accordingly.

*4: With the shift lever in D, accelerate to the maximum possible speed, move the shift lever to M, then shift down to M2 with the accelerator and brake pedals released.

*5: The M position moves up and down according to the vehicle speed.




b.

Repeat drive learning until gear change shock and engine revving subside.

NOTICE:

When repeating drive learning, always begin a new run with the vehicle stopped.




ATF THERMAL DEGRADATION ESTIMATE RESET


NOTICE:

If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset.

·

The ATF has been replaced.

HINT:

If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.


·

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Utility / ATF Thermal Degradation Estimate Reset.

Powertrain > Transmission > Utility
Tester Display
ATF Thermal Degradation Estimate Reset
50005 373 8004