READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
When reviewing Data List information, try to select only the specific Data List items related to the inspection being performed. If all items are selected when checking the Data List, the update time for each item will be longer, resulting in delayed or incorrect data.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0 Max.: 1677215 |
- | - |
| Total Distance Traveled - Unit | Unit for total distance traveled | km or mile | - | - |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
Actual vehicle speed |
·
This is the current vehicle speed.
·
The vehicle speed is detected using the wheel speed sensors.
-
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm Max.: 16383 rpm |
600 to 800 rpm: Idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0% Max.: 100% |
- |
·
This is the engine load calculated based on the estimated intake pressure.
·
Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%) (For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F) Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Intake Air Temperature B1S1 | Intake air temperature (for bank 1 sensor 1) | Min.: -40°C (-40°F), Max.: 215°C (419°F) | Equivalent to temperature at location of mass air flow meter sub-assembly (bank 1) | This is the engine intake air temperature (bank 1).
|
| Intake Air Temperature B1S1 Supported | Status of the intake air temperature B1S1 supported | Supp or Unsupp | Supp | - |
| Intake Air Temperature B1S2 Supported | Status of the intake air temperature B1S2 supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B1S3 Supported | Status of the intake air temperature B1S3 supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B2S1 Supported | Status of the intake air temperature B2S1 supported | Supp or Unsupp | Supp | - |
| Intake Air Temperature B2S2 Supported | Status of the intake air temperature B2S2 supported | Supp or Unsupp | Unsupp | - |
| Intake Air Temperature B2S3 Supported | Status of the intake air temperature B2S3 supported | Supp or Unsupp | Unsupp | - |
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F) Max.: 215°C (419°F) |
Equivalent to ambient air temperature | - |
| Engine Run Time | Engine run time | Min.: 0 seconds Max.: 65535 seconds |
Time after engine start | This is the time elapsed since the engine started.
|
| Battery Voltage | Battery voltage | Min.: 0 V Max.: 65.5 V |
11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| BATT Voltage | Battery voltage | Min.: 0 V Max.: 79.998 V |
11 to 14 V: Idling | - |
| Glow Indicator Supported | Status of glow indicator supported | Unsupp or Supp | - | - |
| Throttle Position Sensor No.1 Voltage % | Absolute throttle position sensor No. 1 | Min.: 0% Max.: 100% |
·
10 to 22%: Accelerator pedal fully released
·
64 to 96%: Accelerator pedal fully depressed (engine running) |
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Neutral Position SW | Park/neutral position switch assembly status | ON or OFF |
·
ON: Shift lever in P or N
·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (Neutral) Supported | Status of Shift SW Status (Neutral) supported | Unsupp or Supp | - | - |
| Transfer L4 | Transfer status | ON or OFF |
·
ON: Transfer in L4
·
OFF: Transfer not in L4 |
- |
| Stop Light SW | Stop light switch status | ON or OFF |
·
ON: Brake pedal depressed
·
OFF: Brake pedal released |
- |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | - |
| Complete Parts Monitor Result | Comprehensive component monitor | Compl or Incmpl | - | - |
| Ignition Monitor | Ignition monitor | Spark Ignition or Compression Ignition | - | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | - |
| Fuel System Monitor Result | Fuel system monitor | Compl or Incmpl | - | - |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | - |
| Misfire Monitor Result | Misfire monitor | Compl or Incmpl | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor Result | EGR/VVT monitor | Compl or Incmpl | - | - |
| A/F (O2) Sensor Heater Monitor | O2S (A/FS) heater monitor | Not Avl or Avail | - | - |
| A/F (O2) Sensor Heater Monitor Result | O2S (A/FS) heater monitor | Compl or Incmpl | - | - |
| A/F (O2) Sensor Monitor | O2S (A/FS) monitor | Not Avl or Avail | - | - |
| A/F (O2) Sensor Monitor Result | O2S (A/FS) monitor | Compl or Incmpl | - | - |
| Secondary Air Injection System Monitor | Secondary air injection system monitor | Not Avl or Avail | - | - |
| Secondary Air Injection System Monitor Result | Secondary air injection system monitor | Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | - |
| EVAP Monitor Result | EVAP monitor | Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | - |
| Heated Catalyst Monitor Result | Heated catalyst monitor | Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | - |
| Catalyst Monitor Result | Catalyst monitor | Compl or Incmpl | - | - |
| TC Terminal | TC terminal Status | ON or OFF | - | - |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven with MIL on | Min.: 0 km (0 mile) Max.: 65535 km (40723 mile) |
- | This is the distance driven after a DTC is stored. |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 minutes Max.: 65535 minutes |
Running time after MIL turned on | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 minutes Max.: 65535 minutes |
Time after DTCs cleared | This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted. |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile) Max.: 65535 km (40723 mile) |
Distance driven after DTCs cleared | This is the distance driven after DTCs were cleared (or after the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0 Max.: 255 |
- |
·
This is the number of warmup cycles after the DTCs were cleared.
·
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started. |
| OBD Requirements | OBD requirement | - | - | - |
| Number of Emission DTC | Emissions-related DTCs | - | - | This is the number of emissions-related DTCs. |
| Accel Position from EFI | Absolute accelerator pedal position | - | - | Value calculated by adding an adjustment value to the actual accelerator pedal position. |
| NT Sensor Speed | Input shaft speed | Min.: 0 rpm Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up engine)
·
Nearly equal to engine speed: Lock-up off (idling with shift lever in N) |
The data is displayed in increments of 50 rpm. |
| Speed (SP2) | Output shaft speed | Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
0 km/h (0 mph): Vehicle stopped (Output shaft speed is equal to vehicle speed) | - |
| SP2 Sensor Voltage | Transmission revolution sensor (SP2) sensor voltage | Min.: 0.000 V Max.: 4.999 V |
0.2 to 1.8 V: Engine idling | - |
| Shift SW Status (P Range) | Park/neutral position switch status | ON or OFF |
·
ON: Shift lever in P
·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch status | ON or OFF |
·
ON: Shift lever in R
·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch status | ON or OFF |
·
ON: Shift lever in N
·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (N,P Range) | Park/neutral position switch status | ON or OFF |
·
ON: Shift lever in P or N
·
OFF: Shift lever not in P or N |
- |
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported | Supp or Unsupp | - | - |
| Shift SW Status (D Range) | Park/neutral position switch status | ON or OFF |
·
ON: Shift lever in D, M, "+" or "-"
·
OFF: Shift lever not in D, M, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F) Max.: 150°C (302°F) |
·
Approximately 80°C (176°F): After stall test
·
Equal to ambient temperature when cold soak |
If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of ATF thermal degradation | Min.: 0 Max.: 65535 |
- | If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF. |
| NT Sensor Voltage | Transmission revolution sensor (NT) sensor voltage | Min.: 0.000 V Max.: 4.999 V |
0.1 to 1.9 V: Engine idling | - |
| Lock Up Status | Lock-up | ON or OFF |
·
ON: Lock-up operating
·
OFF: Lock-up not operating |
- |
| Shift Status | TCM gear shift command | 1st, 2nd, 3rd, 4th, 5th, 6th, 7th, 8th, 9th or 10th | Same as actual gear | - |
| Solenoid (SLT) | Solenoid (SLT) valve status | ON or OFF |
·
ON: Solenoid (SLT) valve operating
·
OFF: Solenoid (SLT) valve not operating |
- |
| Solenoid (SLU) | Solenoid (SLU) valve status | ON or OFF |
·
ON: Lock-up permitted
·
OFF: Lock-up not permitted |
- |
| Solenoid (SL1) | Solenoid (SL1) valve status | ON or OFF |
·
ON: Solenoid (SL1) valve operating
·
OFF: Solenoid (SL1) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL2) | Solenoid (SL2) valve status | ON or OFF |
·
ON: Solenoid (SL2) valve operating
·
OFF: Solenoid (SL2) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL3) | Solenoid (SL3) valve status | ON or OFF |
·
ON: Solenoid (SL3) valve operating
·
OFF: Solenoid (SL3) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL4) | Solenoid (SL4) valve status | ON or OFF |
·
ON: Solenoid (SL4) valve operating
·
OFF: Solenoid (SL4) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL5) | Solenoid (SL5) valve status | ON or OFF |
·
ON: Solenoid (SL5) valve operating
·
OFF: Solenoid (SL5) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL6) | Solenoid (SL6) valve status | ON or OFF |
·
ON: Solenoid (SL6) valve operating
·
OFF: Solenoid (SL6) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL) | Solenoid (SL) valve status | ON or OFF |
·
ON: Lock-up not permitted
·
OFF: Lock-up permitted |
- |
| Solenoid (SR) | Solenoid (SR) valve status | ON or OFF |
·
ON: Solenoid (SR) valve operating
·
OFF: Solenoid (SR) valve not operating |
- |
| Solenoid (SC1) | Solenoid (SC1) valve status | ON or OFF |
·
ON: Solenoid (SC1) valve operating
·
OFF: Solenoid (SC1) valve not operating |
- |
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Accelerator Position | Accelerator pedal position | Min.: 0% Max.: 399.9% |
Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%. |
| Sport Shift Up SW | Sport shift up switch status | ON or OFF |
·
ON: Shift lever held in "+" (up-shift)
·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sport Shift Down SW | Sport shift down switch status | ON or OFF |
·
ON: Shift lever held in "-" (down-shift)
·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Shift SW Status (S Range) | Transmission control switch status | ON or OFF |
·
ON: Shift lever in M, "+" or "-"
·
OFF: Shift lever not in M, "+" or "-" |
- |
| Snow Mode SW | 2nd switch status | ON or OFF |
·
ON: 2ND switch pushed
·
OFF: 2ND switch not pushed |
- |
| Drive Mode Status | Drive mode status | Normal, Power, Sport, Sport+, Comfort or ECO | - | - |
| Endless Rotary Switch (Phase A) | MODE SELECT switch status | ON or OFF | Repeatedly switched ON → OFF → OFF → ON: MODE SELECT switch turned to the right | - |
| Endless Rotary Switch (Phase B) | MODE SELECT switch status | ON or OFF | Repeatedly switched ON → ON → OFF → OFF: MODE SELECT switch turned to the right | - |
| Multi Terrain Select Mode Switching Switch | Multi terrain select mode switch status | ON or OFF |
·
ON: MTS switch pushed
·
OFF: MTS switch not pushed |
- |
| Drive Mode Select Switching Switch | Drive mode select switch status | ON or OFF |
·
ON: DRIVE MODE switch pushed
·
OFF: DRIVE MODE switch not pushed |
- |
| Snow or 2nd Start Mode Status | 2nd start mode status | ON or OFF |
·
ON: 2ND start mode on
·
OFF: 2ND start mode off |
- |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | Transitions into the fluid temperature detection mode. | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Vehicle stopped |
| Control the Shift Position | Operates the solenoid valves to allow gears to selected manually. | 1st/2nd/3rd/4th/5th/6th/7th/8th/9th/10th Start/Stop |
Possible to check operation of the solenoid valves. [Vehicle Condition] Vehicle speed: 50 km/h (30 mph) or less |
| Activate the Solenoid (SLU) | Operates the solenoid (SLU) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SLT) | Operates the solenoid (SLT) valve and raise line pressure | ON/OFF
|
[Vehicle Condition]
·
Ignition switch ON
·
Engine running |
| Activate the Lock Up Solenoid | Controls solenoid (SLU and SL) valves to set automatic transmission to lock-up condition | ON/OFF Start/Stop |
Possible to check solenoid (SLU and SL) valves operation. [Vehicle Condition]
·
Vehicle speed: 90 km/h (56 mph) or more
·
Gear: 9th gear or higher
·
Throttle valve opening angle: Less than 20% |
| Activate the Solenoid (SL) | Operates the solenoid (SL) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SR) | Operates the solenoid (SR) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SC1) | Operates the solenoid (SC1) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL1) | Operates the solenoid (SL1) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL2) | Operates the solenoid (SL2) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL3) | Operates the solenoid (SL3) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL4) | Operates the solenoid (SL4) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL5) | Operates the solenoid (SL5) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
| Activate the Solenoid (SL6) | Operates the solenoid (SL6) valve | ON/OFF | [Vehicle Condition]
·
Ignition switch ON
·
Engine stopped
·
Shift lever in P or N
|
Performing the Active Test "Activate the solenoid (SLT)" allows the change in line pressure to be checked.
The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.
Note that the pressure readings for the Active Test and Hydraulic Test are different.