Home › Engine / Hybrid System › F33A-FTV (STARTING) › STARTER (for 2.7 kW Type) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106336 F33A-FTV STARTING _0489154 STARTER(for 2.7 kW Type) G

F33A-FTV STARTING  STARTER(for 2.7 kW Type)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

When replacing the starter assembly, it is necessary to replace the ST NO. 1 relay as well.


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:
A359265

·

Do not use a thin cable to perform the inspection.

·

If a thin cable is used, the large electric current passing through the cable could cause it to overheat and catch fire, possibly resulting in injuries.



NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a no-load performance test.

i.
A493801C01
2.021,1.469 2.313,1.781 2.313,1.781 2.427,1.781 false 2.521,0.49 2.771,0.302 2.771,0.302 2.917,0.302 false 2.969,0.24 3.281,0.396 0.313,0.156 10 false *a 2.479,1.708 2.792,1.865 0.313,0.156 10 false *b
*a Terminal 50
*b Starter Body
V100135

Moves Outward


Connect the positive (+) lead to terminal 50.


ii.

Connect the negative (-) lead to the starter body and check that the clutch pinion gear moves outward.

NOTICE:

If the positive (+) and negative (-) leads are connected incorrectly, the IC inside of the starter inrush current reduction relay will be damaged. Be sure to connect them correctly.


If the result is not as specified, replace the starter assembly.


iii.
A493802C01
1.948,1.469 2.125,1.906 2.125,1.906 2.25,1.906 false 2.521,0.469 2.729,0.26 2.729,0.26 2.865,0.26 false 2.958,0.208 3.271,0.365 0.313,0.156 10 false *a 2.313,1.833 2.625,1.99 0.313,0.156 10 false *b
*a Terminal 50
*b Starter Body
V113147

Disconnect
V100135

Moves Inward


With the clutch pinion gear in the outward position, disconnect the negative (-) lead and check that the clutch pinion gear returns inward.

If the result is not as specified, replace the starter assembly.


iv.

Hold the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



v.

Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.

A493803C01
3.656,0.188 3.875,0.188 false 2.719,0.875 3.042,0.677 3.042,0.677 3.188,0.677 false 2.115,1.813 2.26,2.156 2.26,2.156 2.396,2.156 false 2.688,1.135 3.042,1.958 3.042,1.958 3.177,1.958 true 3.948,0.125 4.26,0.323 0.313,0.198 10 false *d 3.24,0.604 3.552,0.802 0.313,0.198 10 false *b 2.438,2.063 2.75,2.26 0.313,0.198 10 false *c 3.219,1.865 3.531,2.063 0.313,0.198 10 false *a
*a Terminal 30 *b Terminal 50
*c Starter Body *d AC/DC 400 A Probe



vi.

Connect terminal SL2 and measure the current after the ammeter (AC/DC 400A probe) reading has stabilized.

Standard current:

90 A or less at 11.0 V


If the result is not as specified, repair or replace the starter assembly.