Home › Engine / Hybrid System › F33A-FTV (STARTING) › ENGINE SWITCH › from 2021.07
RM38G0E _51 Engine / Hybrid System _106336 F33A-FTV STARTING _0489155 ENGINE SWITCH G

F33A-FTV STARTING  ENGINE SWITCH  INSPECTION  


PROCEDURE

Hide 89611 1.INSPECT ENGINE SWITCH

a.
A463220C04
1.417,0.083 1.917,0.333 0.5,0.25 1.885,0.969 2.583,0.167 2.583,0.167 2.75,0.167 true 1.167,1.333 0.833,1.833 0.833,1.833 0.667,1.833 true 1.917,1.833 1.75,1.833 1.75,1.833 1.438,1.344 true 1.167,0.969 0.917,0.333 0.917,0.333 0.75,0.333 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.833,0.083 3.167,0.25 0.333,0.167 10 false GND 0.333,1.75 0.667,1.917 0.333,0.167 10 false SS1 0.417,0.25 0.75,0.417 0.333,0.167 10 false SS2 2,1.75 2.333,1.917 0.333,0.167 10 false SS3 1.573,0.125 1.906,0.292 0.333,0.167 10 false I75
*a Component without harness connected
(Engine Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-12 (SS1) - I75-3 (GND)
I75-6 (SS2) - I75-3 (GND)
I75-11 (SS3) - I75-3 (GND)
Not pushed 10 kΩ or higher
Pushed Below 1 Ω


If the result is not as specified, replace the engine switch.


b.
A463220C05
1.5,0.167 2,0.417 0.5,0.25 1.885,0.969 2.5,0.25 2.5,0.25 2.667,0.25 true 1.375,0.969 0.917,0.5 0.917,0.5 0.75,0.5 true 2.75,0.167 3.167,0.333 0.417,0.167 10 false GND 0.333,0.417 0.75,0.583 0.417,0.167 10 false SWIL 0.104,0.073 0.719,0.271 0.615,0.198 10 false *a 1.656,0.208 1.906,0.375 0.25,0.167 10 false I75
*a Component without harness connected
(Engine Switch)


Apply battery voltage between the terminals of the engine switch, and check the illumination condition of the engine switch indicator light.

OK:
Condition Specified Condition
Battery positive (+) - I75-5 (SWIL)
Battery negative (-) - I75-3 (GND)
Illuminates


HINT:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator light will not illuminate.

·

If the voltage is too low, the engine switch indicator light will not illuminate.



If the result is not as specified, replace the engine switch.