81985 1.INSPECT TOWING CONVERTER RELAY
Disconnect the towing converter relay connector.
| *a | Front view of wire harness connector (to Towing Converter Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(T17)Location & Routingewd_type=routing;type=c;code=T17 Click Connector(T17)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Towing Converter Relayewd_type=component;type=c;code=T17;pinno=1 |
||
| T17-1 (+B) - Body ground | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(T17)Location & Routingewd_type=routing;type=c;code=T17 Click Connector(T17)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Towing Converter Relayewd_type=component;type=c;code=T17;pinno=6 |
||
| T17-6 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the towing converter relay connector.
Ignition switch to ON.
| *a | Component with harness connected (Towing Converter Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(T17)Location & Routingewd_type=routing;type=c;code=T17 Click Connector(T17)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Towing Converter Relayewd_type=component;type=c;code=T17;pinno=9,3,4,2,8 |
||
| T17-9 (LTIN) - Body ground | Turn signal switch (left turn) off | Below 1 V |
| T17-9 (LTIN) - Body ground | Turn signal switch (left turn) On | 11 to 14 V |
| T17-3 (RTIN) - Body ground | Turn signal switch (right turn) off | Below 1 V |
| T17-3 (RTIN) - Body ground | Turn signal switch (right turn) On | 11 to 14 V |
| T17-4 (LTOT) - Body ground | Turn signal switch (left turn) off | Below 1 V |
| T17-4 (LTOT) - Body ground | Turn signal switch (left turn) On | 11 to 14 V |
| T17-4 (LTOT) - Body ground | Turn signal (left turn) off while depressing brake pedal |
Below 1 V |
| T17-4 (LTOT) - Body ground | Turn signal (left turn) On while depressing brake pedal |
11 to 14 V |
| T17-4 (LTOT) - Body ground | Brake pedal depressed | 11 to 14 V |
| T17-2 (RTOT) - Body ground | Turn signal switch (right turn) off | Below 1 V |
| T17-2 (RTOT) - Body ground | Turn signal switch (right turn) On | 11 to 14 V |
| T17-2 (RTOT) - Body ground | Turn signal (right turn) off while depressing brake pedal |
Below 1 V |
| T17-2 (RTOT) - Body ground | Turn signal (right turn) On while depressing brake pedal |
11 to 14 V |
| T17-2 (RTOT) - Body ground | Brake pedal depressed | 11 to 14 V |
| T17-8 (STIN) - Body ground | Brake pedal depressed | 11 to 14 V |
If the result is not as specified, there is a problem in the towing converter relay or wire harness.
81985A 2.INSPECT TOWING BACK-UP RELAY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the towing back-up relay.
81985B 3.INSPECT TOWING STOP LAMP RELAY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the towing stop lamp relay.
85916Y 4.INSPECT TOWING TAIL RELAY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the towing tail relay.