This circuit supplies electric power to the variable flow control solenoid valve (vane pump assembly).
The power steering ECU assembly controls the output current to the variable flow control solenoid valve (vane pump assembly) in accordance with the steering angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C15F014 | VFC Solenoid Circuit Circuit Short to Ground or Open | A short or open in the solenoid valve circuit |
·
Harness or connector
·
Vane pump assembly
·
Power steering ECU assembly |
Output ECU: Power steering ECU assembly |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | A short in the solenoid valve circuit | ○ | - |
| An open in the solenoid valve circuit | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Solenoid Actual Current (PPS) | Solenoid Current | Min.: 0 mA Max.: 1000 mA |
200 to 950 mA: Engine running and steering wheel being turned | - |
| Tester Display |
|---|
| Solenoid Actual Current (PPS) |
The normal condition value is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I29 power steering ECU assembly connector.
Disconnect the C49 variable flow control solenoid valve (vane pump assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I29,C49)Location & Routingewd_type=routing;type=c,c;code=I29,C49 |
||
| I29-7 (SOF+) - C49-2 (SOF+) | Always | Below 1 Ω |
| I29-8 (SOF-) - C49-1 (SOF-) | Always | Below 1 Ω |
| I29-7 (SOF+) or C49-2 (SOF+) - Body ground | Always | 10 kΩ or higher |
| I29-8 (SOF-) or C49-1 (SOF-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C49 variable flow control solenoid valve (vane pump assembly) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Variable Flow Control Solenoid Valve (Vane Pump Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C49)Location & Routingewd_type=routing;type=c;code=C49 |
||
| C49-1 (SOF-) - C49-2 (SOF+) | 20°C (68°F) | 6.7 to 7.3 Ω |
Connect the positive (+) lead of the battery with a 21 W bulb to terminal 2 (SOF+) and the negative (-) lead to terminal 1 (SOF-) of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
Valve moves and makes an operating noise.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for V35A-FTS: Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (for V35A-FTS)>REMOVAL
for F33A-FTV: Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (for F33A-FTV)>REMOVAL