Home › Engine / Hybrid System › F33A-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › from 2021.07
RM38G0E _51 Engine / Hybrid System _106332 F33A-FTV EMISSION CONTROL _0491911 EMISSION CONTROL SYSTEM G

F33A-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.


HINT:

When there is a malfunction which causes the EGR system to remain on, black or white smoke may be emitted from the exhaust pipe.


PROCEDURE

Hide 25800 1.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY OPERATION (w/ EGR System)

a.

Perform the active test to operate the EGR valve.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position Bank 1
Data List Display
Target EGR Valve Position No.1
Actual EGR Valve Position No.1
50004 372 70 381,382
Standard:

The actual value follows the target value.


If the result is not as specified, refer to DTC P040371.Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P040371


Hide 2.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, PCV hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the diesel throttle body and cylinder head will cause engine failure or engine malfunctions.




Hide 3.PERFORM DPF FORCIBLE REGENERATION PROCEDURE (w/ DPR)

CAUTION:

While the DPF forcible regeneration, the exhaust gas temperature will be high.

Remove any fusible things around the engine and exhaust tail pipe.


HINT:
·

While the DPF forcible regeneration, the engine speed varies.

·

It takes 15 to 40 minutes.

·

It does not work when the data list: PM Accumulation Ratio is lower than aproximately 12%.

·

It is completed when the PM Accumulation Ratio is lower than aproximately 10%.

·

Do not cancel in the middle. If it is cancelled, perform it again from the beginning.

·

Either of the followings allows it to cancel:

- Push the DPR switch.

- Race the engine with the accelerator pedal.

- Depress the clutch pedal.

- The Particulate Filter Differential Pressure increased.

·

It may not work at low outside temperature or high elevation. Then, perform it indoors and the exhaust tailpipe towards the outside. Or, drive with more than 60 km/h (37 mph) for 15 minutes or more instead of the DPF forcible regeneration.

·

If it takes more than 60 minutes, it is forcibly cancelled and the MIL is on. Disconnect the negative battery cable for 1 minute at least. Confirm the MIL is off, then retry it.



a.

Move the shift lever to P or neutral and apply the parking brake.


b.

Clear DTCs if thay are present. The DPF forcible regeneration will not work if the DPF related DTC is set.


c.

Warm up the engine until the engine coolant temperature stable.


d.

Use GTS and perform DPF forcible regeneration.

Powertrain > Engine > Utility
Tester Display
PM Regenerate Mode
50005 372 4576

e.

Allow the engine to idle for 5 minutes or more.


f.

Fully depress the brake pedal and fully depress the accelerator pedal for 5 seconds, then read the data list.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138
Standard:
Cental value of the data:

15 kPa or less


If the result is not as specified, replace the exhaust manifold converter sub-assembly.